General information
Note | Integrated passive motor short circuit brake |
B&R ID code | 0xA988 |
Support | |
Dynamic node allocation (DNA) | Yes |
Cooling and mounting type | Wall mounting |
Certifications | |
CE | Yes |
UKCA | Yes |
UL |
cULus E225616 Power conversion equipment |
EAC | Yes |
KC | Yes |
Mains connection
DC bus connection
24 VDC power supply
Input voltage | 25 VDC ±1.6% |
Input capacitance | 23.5 µF |
Max. power consumption | 12 W |
Variant | ACOPOSmulti backplane |
Braking resistor
Electrical properties
Discharge capacitance | 0.9 µF |
Operating conditions
Ambient conditions
Temperature | |
Operation | |
Nominal | 5 to 40°C |
Maximum | 55°C |
Storage | -25 to 55°C |
Transport | -25 to 70°C |
Relative humidity | |
Operation | 5 to 85% |
Storage | 5 to 95% |
Transport | Max. 95% at 40°C |
Materiálové číslo:
8B0P0220HW00.001-1Popis:
- Wide input voltage range
- Integrated connection for external braking resistor
- Passive motor short circuit brake
A motor with a hanging load is connected to an ACOPOSmulti drive system with passive power supply module 8B0P with passive motor short circuit brake. If the power supply to the drive system is disconnected and the hanging load begins sinking (due to failure of the motor holding brake, for example), then the motor axis rotates and the DC bus voltage increases. If the DC bus voltage overshoots a value of 15 VDC, then the DC bus is shorted via a thyristor. This limits the speed at which the hanging load sinks.
The passive motor short circuit brake is designed for up to 25 kW of power. One fault event is permitted to occur maximum once every 15 minutes for this amount of power.
The passive motor short circuit brake is always active and cannot be influenced by the user!
The passive motor short circuit brake works without current limiting. As a result, irreparable damage to drive system components (passive power supply module 8B0P, motor, etc.) is possible at excessively high power values.
The passive motor short circuit brake is not monitored. It therefore has no effect in the event of component failure!
Povinné příslušenství
Terminal block sets
8BZ0P044000.000-1A | Screw clamp terminal block set for ACOPOSmulti 8B0P0220Hx00.00x-1 and 8B0P0440Hx00.00x-1 modules: 1x 8TB4104.202L-10, 1x 8TB4103.202A-00, 1x 8TB2106.2010-00 |
Volitelné příslušenství
Braking resistors
8B0W0045H000.000-1 | Braking resistor, 450 W, 50 R, IP20, terminals |
8B0W0045H000.001-1 | Braking resistor, 450 W, 50 R, IP65, terminals |
8B0W0079H000.000-1 | Braking resistor, 790 W, 33 R, IP20, terminals |
8B0W0079H000.001-1 | Braking resistor, 790 W, 33 R, IP65, terminals |
Fan modules
8BXF001.0000-00 | ACOPOSmulti fan module, replacement fan for ACOPOSmulti modules (8BxP/8B0C/8BVI/8BVE/8B0K) |
Fuse sets
8BXS003.0000-00 | ACOPOSmulti fuse set: 1x fuse 10 x 38 mm, 30 A, fast-acting |
POWERLINK/Ethernet cables
X20CA0E61.00020 | POWERLINK/Ethernet connection cable, RJ45 to RJ45, 0.2 m |
X20CA0E61.00025 | POWERLINK/Ethernet connection cable, RJ45 to RJ45, 0.25 m |
X20CA0E61.00030 | POWERLINK/Ethernet connection cable, RJ45 to RJ45, 0.3 m |
X20CA0E61.00035 | POWERLINK/Ethernet connection cable, RJ45 to RJ45, 0.35 m |
X20CA0E61.00050 | POWERLINK/Ethernet connection cable, RJ45 to RJ45, 0.5 m |
X20CA0E61.00100 | POWERLINK/Ethernet connection cable, RJ45 to RJ45, 1 m |
Shield component sets
8SCS000.0000-00 | ACOPOSmulti shield component set: 1x shield plate 1x type 0, 1x hose clamp, B 9 mm, D 12-22 mm |
8SCS002.0000-00 | ACOPOSmulti shield component set: 1x clamping plate, 2x clamp D 4-13.5 mm, 2x screws |
8SCS009.0000-00 | ACOPOSmulti shield component set: 1x ACOPOSmulti holding plate SK8-14, 1x shield connection clamp SK14 |
8SCS010.0000-00 | ACOPOSmulti shield component set: 1x ACOPOSmulti holding plate SK14-20, 1x shield connection clamp SK20 |
Terminal blocks
8TB2106.2010-00 | 6-pin screw clamp terminal block, 1-row, pitch: 5.08 mm, label 1: Numbered consecutively |
8TB4103.202A-00 | 3-pin screw clamp terminal block, one-row, pitch: 10.16 mm, label 2: PE RB- RB+, coding A: 000 |
8TB4104.202L-10 | Screw clamp terminal block 4-pin, one-row, pitch: 10.16 mm, label 2: PE L3 L2 L1, coding L: 1010 |
Automation Studio HW Upgrades | Verze (datum) | Ke stažení |
---|---|---|
V3.0 HW Upgrade (8B0PXXXXXXXX.XXX-X) | EXE / 399 KB | |
V4.0 HW Upgrade (8B0P0220HW00.001-1) | EXE / 312 KB | |
V4.0 HW Upgrade (8B0Pxxxxxxxx.xxx-1) | EXE / 676 KB | |
V4.0 HW Upgrade (8B0Pxxxxxxxx.xxx-x) | EXE / 517 KB |
Dokumentace | Verze (datum) | Ke stažení |
---|---|---|
ACOPOSmulti User´s Manual | PDF / 302 MB | |
Datasheet 8B0P0220HW00.001-1 | PDF / 4 MB |
E-CAD (Electro or EPLAN Templates) | Verze (datum) | Ke stažení |
---|---|---|
ACOPOSmulti EPLAN P8 from V2.4 | EXE / 81 MB |
M-CAD (Mechan. Templates) | Verze (datum) | Ke stažení |
---|---|---|
3D file STEP 8B0P0xx0HW00.00x-1 | ZIP / 156 KB |