DWL@DWL10000777839
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
|---|---|---|---|---|---|---|
| 2.6.0.0 | * | 05.03.2024 | 1 MB | EXE | AS6_HW_X20SC2432.exe | |
| Popis |
V6.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 2.6.0.0: ID: 780145 Correction of the input filter with set "Filter off". Correction of the input filter, if a "Filter off" is set and a channel error is detected. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 780265 New data sheet V2.20 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 780390 / Support ID: 400412437 Configuration for Power Calculation available The Configuration for Power Calculation is now available in Automation Studio Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 10\42916_1.fw(580) Version 2.5.0.0: ID: 715240 Failsafe at every boot It could happen under rare conditions that the module is stuck in failsafe state at every boot, generating logger messages: -1073565951/-1073561855 "internal cross communication error EPS" or -1073565945/-1073561849 "Received crc data is not equal to sent crc data" Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 726660 The power calculation of the modules is supported The data for the power calculation of the data sheet is included in the HWX. Channel description changed: No Configuration description changed: No Firmware changed: No ID:727185 New data sheet V2.10 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\42916_1.fw(575) Version 2.4.1.0: ID: 692350 Support of the DYNlink interface The DYNlink interface is supported by the safe inputs. Channel description changed: No Configuration description changed: Yes Firmware changed: Yes ID: 692390 The OSDD signal at the pulse output is corrected. The OSDD signal at the pulse output is output correctly even when not in use. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 696560 New data sheet V2.08 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 706320 Limit values forthe module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 10\42916_1.fw(574) Version 2.3.0.0: ID: 668550 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688720 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration"is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689740 Propagation delay statistics The Propagation delay statisticscan now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689975 Improvement of the internal voltage monitoring. Improvement of the internalvoltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690130 Newdata sheet V2.06 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\42916_1.fw(572) Version 2.1.0.0: ID: 644190 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\42916_1.fw(570) Version 1.10.10.1: ID: 643305 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has beenupdated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.0: ID: 621345 /Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 622110 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065,110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Logger entry 112174, 108078could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in the OSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed:No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Addedcoated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel descriptionchanged: No Configuration description changed: No Firmware changed:No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configurationdescription changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed:No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supportsSafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of moduleconfiguration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2safety processors to reduce the numberof messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
