8BVI0055HWSA.000-1

General information
Support
Dynamic node allocation (DNA) Yes
Certifications
CE Yes
UKCA Yes
CRA (Cyber Resilience Act) In preparation
Functional safety Yes (openSAFETY)
UL cULus E225616
Power conversion equipment
B&R ID code 0xE0B3
Cooling and mounting type Wall mounting
Slots for plug-in modules 2
DC bus connection
Voltage
Nominal 750 VDC
Power dissipation depending on switching frequency
Switching frequency 5 kHz [0.6 * IM² + 1.3 * IM + 60] W
Switching frequency 10 kHz [0.97 * IM² + 0.5 * IM + 110] W
Switching frequency 20 kHz [1.7 * IM² - 0.7 * IM + 225] W
Continuous power consumption 5.6 kW
DC bus capacitance 165 µF
Variant ACOPOSmulti backplane
24 VDC power supply
Input voltage 25 VDC ±1.6%
Input capacitance 23.5 µF
Max. power consumption 25 W + PSMC1 + PSLOT2 + P24 V Out + PHoldingBrake
Variant ACOPOSmulti backplane
24 VDC output
Output voltage
DC bus voltage (UDC): 260 to 315 VDC 25 VDC * (UDC/315)
DC bus voltage (UDC): 315 to 800 VDC 24 VDC ±6%
Quantity 2
Fuse protection 250 mA (slow-blow) electronic, automatic reset
Motor connection
Reduction of continuous current depending on switching frequency
Switching frequency 5 kHz No reduction
Switching frequency 10 kHz 0.2 A/K (starting at 49°C)
Switching frequency 20 kHz 0.13 A/K (starting at 4°C)
Reduction of continuous current depending on installation elevation
Starting at 500 m above sea level 0.76 Aeff per 1000 m
Protective measures
Overload protection Yes
Short-circuit and ground fault protection Yes
Variant
U, V, W, PE Connector
Shield connection Yes
Terminal connection cross section
Flexible and fine-stranded wires
With wire end sleeve 0.25 to 4 mm²
Approbation data
UL/C-UL-US 30 to 10
CSA 28 to 10
Max. motor line length depending on switching frequency
Switching frequency 5 kHz 25 m
Switching frequency 10 kHz 25 m
Switching frequency 20 kHz 10 m
Quantity 1
Continuous power per motor connection 5.5 kW
Continuous current per motor connection 7.6 Aeff
Peak current 18.9 Aeff
Nominal switching frequency 5 kHz
Possible switching frequencies 5 / 10 / 20 kHz
Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
Max. output frequency 598 Hz
Terminal cable cross section dimension of shield connection 12 to 22 mm
Motor holding brake connection
Protective measures
Overload and short-circuit protection Yes
Open-circuit monitoring Yes
Undervoltage monitoring Yes
Quantity 1
Output voltage 24 VDC +5.8% / -0%
Continuous current per connection 1.1 A
Max. internal resistance 0.5 Ω
Extinction potential Approx. 30 V
Max. extinction energy per switching operation 1.5 Ws
Max. switching frequency 0.5 Hz
Response threshold for open-circuit monitoring Approx. 0.25 A
Response threshold for undervoltage monitoring 24 VDC -2% / -4%
Encoder interfaces
Electrical isolation
Encoder - ACOPOSmulti No
Encoder power supply
Protective measures
Short-circuit proof Yes
Overload-proof Yes
Output voltage 5 V ±5%
Load capacity 300 mA
Sense lines 2, compensation of max. 2 x 0.7 V
Synchronous serial interface
Signal transmission RS485
Data transfer rate 781.25 kbit/s
Sine/Cosine inputs
Differential voltage
In motion 0.5 to 1.35 V
At standstill 0.8 to 1.35 V
Signal transmission Differential signals, symmetrical
Differential voltage deviation per signal period ±10%
Common-mode voltage Max. ±7 V
Terminating resistor 120 Ω
Max. input frequency 200 kHz
Signal frequency (-5 dB) <300 kHz
Signal frequency (-3 dB) DC up to 200 kHz
ADC resolution 12-bit
Reference input
Signal transmission Differential signal, symmetrical
Differential voltage for low ≤-0.2 V
Differential voltage for high ≥0.2 V
Common-mode voltage Max. -5 V to +9 V
Terminating resistor 120 Ω
Position
Resolution @ 1 VSS Number of encoder lines * 5700
Accuracy ---
Noise ---
Quantity 1
Type SinCos
Connections 15-pin female DSUB connector
Status indicators UP/DN LEDs
Encoder monitoring Yes
Max. encoder cable length 50 m
Max. power consumption per encoder interface PSMC[W] = 25 V * (0.376 A + 0.35 * IEncoder[A])
Trigger inputs
Electrical isolation
Input - Inverter module Yes
Input - Input Yes
Input voltage
Nominal 24 VDC
Maximum 30 VDC
Switching threshold
Low <5 V
High >15 V
Switching delay
Rising edge 52 µs ±0.5 µs (digitally filtered)
Falling edge 53 µs ±0.5 µs (digitally filtered)
Quantity 2
Circuit Sink
Input current at nominal voltage Approx. 10 mA
Modulation compared to ground potential Max. ±38 V
Temperature sensor connection
Quantity 1
Resistance range 500 Ω to 5 kΩ
Electrical properties
Energy efficiency (IE classification)
Power dissipation relative to continuous apparent power IE2 (10,25) 2.7%
IE2 (50,25) 2.7%
IE2 (10,50) 3%
IE2 (50,50) 2.9%
IE2 (90,50) 2.9%
IE2 (10,100) 3.5%
IE2 (50,100) 3.5%
IE2 (90,100) 3.5%
Nominal losses in standby mode 8.5 W
Discharge capacitance 0.14 µF
Operating conditions
Permissible mounting orientations
Hanging vertically Yes
Horizontal, face up Yes
Standing horizontally No
Installation elevation above sea level
Nominal 0 to 500 m
Maximum 4000 m
Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
Overvoltage category per EN 61800-5-1 III
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Nominal 5 to 40°C
Maximum 55°C
Storage -25 to 55°C
Transport -25 to 70°C
Relative humidity
Operation 5 to 85%
Storage 5 to 95%
Transport Max. 95% at 40°C
Mechanical properties
Dimensions
Depth
Wall mounting 263 mm
Width 53 mm
Height 317 mm
Weight Approx. 2.7 kg
Module width 1
Référence produit:
8BVI0055HWSA.000-1
Description:
ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
Accessoires obligatoires
Terminal block sets
8BZVI0055SS.000-1A ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
Accessoires optionnels
Accessory sets
8BXB000.0000-00 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
Fan modules
8BXF001.0000-00 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
POWERLINK/Ethernet cables
X20CA0E61.00020 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
X20CA0E61.00025 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
X20CA0E61.00030 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
X20CA0E61.00035 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
X20CA0E61.00050 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
X20CA0E61.00100 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
Plug-in modules
8BAC0120.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0120.001-2 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0121.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0122.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0123.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0123.001-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0123.002-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0124.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0125.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0130.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0130.001-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0132.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8BAC0133.000-1 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
Shield component sets
8SCS000.0000-00 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8SCS002.0000-00 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8SCS009.0000-00 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
Terminal blocks
8TB2104.203L-00 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8TB2108.2010-00 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
8TB3104.204G-11 ACOPOSmulti SafeMOTION SinCos inverter module, 7.6 A, AS, wall mounting
Automation Studio HW Upgrades Version (date) Téléchargement
V3.0 HW Upgrade (8BVIxxxxxxSA.xxx-x) EXE / 397 Ko
V3.0 HW Upgrade (8BVSV2S_21ENC1-1) EXE / 750 Ko
V4.0 HW Upgrade (8BVI0055HWSA.000-1) EXE / 248 Ko
V4.0 HW Upgrade (8BVIxxxxxxSA.xxx-1) EXE / 573 Ko
V4.0 HW Upgrade (8BVIxxxxxxSA.xxx-x) EXE / 249 Ko
V4.0 HW Upgrade (8BVSV2S_21ENC1-1) EXE / 944 Ko
V4.6 HW Upgrade (8BVSV2S_21ENC1-1) EXE / 901 Ko
V6.0 HW Upgrade (8BVI0055HWSA.000-1) EXE / 297 Ko
V6.0 HW Upgrade (8BVIxxxxxxSA.xxx-1) EXE / 297 Ko
V6.0 HW Upgrade (8BVIxxxxxxSA.xxx-x) EXE / 297 Ko
V6.0 HW Upgrade (8BVSV2S_21ENC1-1) EXE / 624 Ko
Certifications Version (date) Téléchargement
E225616 UL Certificate of Compliance ACOPOSmulti (UL 508C) PDF / 282 Ko
E225616 UL Certificate of Compliance ACOPOSmulti (UL 61800-5-1) PDF / 183 Ko
EU Declaration FS Servos ACOPOSmulti PDF / 986 Ko
EU Declaration Servos ACOPOSmulti PDF / 963 Ko
TÜV-Certificate - Functional Safety ACOPOSmulti SafeMOTION SinCos ZIP / 832 Ko
UK Declaration FS Servos ACOPOSmulti PDF / 341 Ko
UK Declaration Servos ACOPOSmulti PDF / 337 Ko
Documentation Version (date) Téléchargement
Datasheet 8BVI0055HWSA.000-1 PDF / 4 Mo
Integrated safety technology user's manual PDF / 59 Mo
SafeMOTION User´s Manual PDF / 34 Mo
E-CAD (modèles Electro ou EPLAN) Version (date) Téléchargement
ACOPOSmulti EPLAN P8 from V2.4 EXE / 81 Mo
Généralités Version (date) Téléchargement
Verification of the requirements placed on non-certified measuring instr PDF / 1 Mo
M-CAD (modèles mécaniques) Version (date) Téléchargement
3D file STEP 8BVI0055HWSx.000-x ZIP / 150 Ko

Veuillez sélectionner un pays et une langue

B&R Logo