DWL@DWL10000303945
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
|---|---|---|---|---|---|---|
| 2.11.0.0 | * | 20/02/2020 | 3 Mo | EXE | AS3.0_HW_X67BC8321.L12.exe | |
| Description |
V3.0 HW Upgrade (X67BC8321.L12) Revision information X67BC8321.L12 Version 2.11.0.0: ID: 664430 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664460 DNA: Hub of PLK BCactive until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665785 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665875 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 666155 Module documentation revised Data sheet V2.08 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\43278_1.fw(430), 1\43278_2.fw(430), 1\43278_3.fw(430), 1\43278_4.fw(430) Version 2.9.3.0: ID: 639725 / Support ID: 400268096 Alignment of AS output according to the FieldBusDesigner Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(427), 1\43278_2.fw(427),1\43278_3.fw(427), 1\43278_4.fw(427) Version 2.9.0.0: ID: 624525 L/A IF LED permanently green although Ethernet activity is taking place on the bus Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 625035 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629045 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629120 DNA: BC as head-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629195 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(427), 1\43278_2.fw(427), 1\43278_3.fw(427), 1\43278_4.fw(427) Version 2.8.0.0: ID: 619235 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 619265 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 621710 Display of further diagnostic data points in the I / O mapping of the X2X interface from the X67 bus controller Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 624315 Firmwareupdate of X2XLink module at POWERLINK Stations does not work since H4.34 Since H4.34 the firmware update of X2XLink modules connected to X67BC8321-1did not work, if they are connected to POWERLINK-Buscontrollers that have no explicit enable for streaming. Problem occurs on BC and SL: X20BC0083 X20cBC0083 < HW-Upgrade 2.2.0.0 X20BC1083 X20cBC1083 < HW-Upgrade 2.5.0.0 X20BC8083 X20cBC8083 < HW-Upgrade 2.5.0.0 X20BC8084 X20cBC8084 < HW-Upgrade 2.5.0.0 X20SL8101 X20cSL8101 X67BC81RT.L12 < HW-Upgrade 2.5.0.0 X67BC8321-1 X67BC8331 X67BC8513.L12 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(426), 1\43278_2.fw(426), 1\43278_3.fw(426), 1\43278_4.fw(426) Version 2.5.5.0: ID: 551150 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(421), 1\43278_2.fw(421),1\43278_3.fw(421), 1\43278_4.fw(421) Version 2.5.4.0: ID: 540350 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(419), 1\43278_2.fw(419), 1\43278_3.fw(419), 1\43278_4.fw(419) Version 2.5.3.0: ID: 523585 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDPis not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(417), 1\43278_2.fw(417), 1\43278_3.fw(417), 1\43278_4.fw(417) Version 2.5.2.0: ID: 493935 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(415), 1\43278_2.fw(415), 1\43278_3.fw(415), 1\43278_4.fw(415) Version 2.5.0.0: ID: 468190 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468195 / SupportID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468200 / Support ID: 400178654 Safetymodules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468575 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(413), 1\43278_2.fw(413), 1\43278_3.fw(413), 1\43278_4.fw(413) Version 2.2.1.0: ID:460140 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460260 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(412), 1\43278_2.fw(412), 1\43278_3.fw(412), 1\43278_4.fw(412) Version 2.1.0.0: ID: 385270 / Support ID: 400132264 hwc, hwx adaption Channel address adapted for fieldbusdesigner Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 439135 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439240 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(400), 1\43278_2.fw(400), 1\43278_3.fw(400), 1\43278_4.fw(400) Version 2.0.0.1: ID: 390305 / Support ID: 400129274 Uncommon X2X settingscause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 392930 / Support ID: 400138511 X2X communication revised A new firmware for hardware variant 3 (BC-Part) was released. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(211), 1\43278_2.fw(211), 1\43278_3.fw(211), 1\43278_4.fw(211) Version 2.0.0.0: ID: 390305 / Support ID: 400129274 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(210), 1\43278_2.fw(210), 1\43278_3.fw(210), 1\43278_4.fw(210) Version 1.3.4.0: ID: 310815 / Support ID: 400097674 POWERLINK V1: Bug-fix for Up/Downgrade POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 311035 / Support ID: 400051206 Expansion: Link- selector flag New datapoints:<br/>- RedundancyFirstLinkState<br/>- RedundancySecondLinkState Channel description changed: Yes Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(168), 1\43278_2.fw(168), 1\43278_3.fw(168), 1\43278_4.fw(168) Version 1.3.3.0: ID: 305175 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 305180 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When therewas a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(167), 1\43278_2.fw(167), 1\43278_3.fw(167),1\43278_4.fw(167) Version 1.3.2.0: ID: 299000 / Support ID: 400090781 Problem with FW-Update of IO modules on Powerlink buscontrollers The firmware update of IO modules does not work in certain configurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(165), 1\43278_2.fw(165), 1\43278_3.fw(165), 1\43278_4.fw(165) Version 1.3.1.0: ID: 289030 Certain X2X configurations don't work In very rare I/O constellations, the X2X modules don't start Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(163), 1\43278_2.fw(163), 1\43278_3.fw(163), 1\43278_4.fw(163) Version 1.3.0.0: ID: 277190 Support of 'Multiple Asynchronous Send' Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 277760 New X2X datapoints - NettimeOffsetX2X and NettimeX2X Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(160), 1\43278_2.fw(160), 1\43278_3.fw(160), 1\43278_4.fw(160) Version 1.2.3.0: ID: 268080 / Support ID: 400072663 Error in FPGA cause a problem in the MAC effect: causes a losingconnection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 268580 New hardwarevariant New hardware variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(154), 1\43278_2.fw(154), 1\43278_3.fw(154), 1\43278_4.fw(154) Version 1.2.2.0: ID: 246365 DNA support; Update behavior on X2X bus of the BC improved - DNA support (Dynamic Node Allocation) - faster updating of modules with big FW files on the X2X bus of the BC - new objects: 20A3h and 2000h/9 - support for Simulation device added Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(152), 1\43278_2.fw(152), 1\43278_3.fw(152) Version 1.0.3.0: ID: 240470 / Support ID: . Correction of X67BCOnboard Compatible Code Channel description changed: No Configuration description changed: Yes Firmware changed:No Firmware: 1\43278_1.fw(144) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.9.0.0 | * | 13/03/2019 | 3 Mo | EXE | AS3.0_HW_X67BC8321.L12.exe | |
| Description |
V3.0 HW Upgrade (X67BC8321.L12) Revision information X67BC8321.L12 Version 2.9.0.0: ID: 624525 L/A IF LED permanently green although Ethernet activity is taking place on the bus Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 625035 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629045 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629120 DNA: BC ashead-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629195 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(427), 1\43278_2.fw(427), 1\43278_3.fw(427), 1\43278_4.fw(427) Version 2.8.0.0: ID: 619235 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619265 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 621710 Display of further diagnostic data points in the I / O mapping of the X2X interface from the X67 bus controller Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 624315 Firmwareupdate of X2XLink module at POWERLINK Stations does not work since H4.34 Since H4.34 the firmware update of X2XLink modules connected to X67BC8321-1did not work, if they are connected to POWERLINK-Buscontrollers that have no explicit enable for streaming. Problem occurs on BC andSL: X20BC0083 X20cBC0083 < HW-Upgrade 2.2.0.0 X20BC1083 X20cBC1083 < HW-Upgrade 2.5.0.0 X20BC8083 X20cBC8083 < HW-Upgrade 2.5.0.0 X20BC8084 X20cBC8084 < HW-Upgrade 2.5.0.0 X20SL8101 X20cSL8101 X67BC81RT.L12 < HW-Upgrade 2.5.0.0 X67BC8321-1 X67BC8331 X67BC8513.L12 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(426), 1\43278_2.fw(426), 1\43278_3.fw(426), 1\43278_4.fw(426) Version 2.5.5.0: ID: 551150 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(421), 1\43278_2.fw(421), 1\43278_3.fw(421), 1\43278_4.fw(421) Version 2.5.4.0: ID: 540350 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(419), 1\43278_2.fw(419), 1\43278_3.fw(419), 1\43278_4.fw(419) Version 2.5.3.0: ID: 523585 /Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(417), 1\43278_2.fw(417), 1\43278_3.fw(417), 1\43278_4.fw(417) Version 2.5.2.0: ID: 493935 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(415), 1\43278_2.fw(415), 1\43278_3.fw(415), 1\43278_4.fw(415) Version 2.5.0.0: ID: 468190 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468195 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468200 / Support ID: 400178654 Safety modules in connection with PLK BCs, withonly input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468575 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(413), 1\43278_2.fw(413), 1\43278_3.fw(413), 1\43278_4.fw(413) Version 2.2.1.0: ID: 460140 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460260 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(412), 1\43278_2.fw(412), 1\43278_3.fw(412), 1\43278_4.fw(412) Version 2.1.0.0: ID: 385270 / Support ID: 400132264 hwc, hwx adaption Channel address adapted for fieldbusdesigner Channeldescription changed: Yes Configuration description changed: No Firmware changed: No ID: 439135 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configurationdescription changed: No Firmware changed: Yes ID: 439240 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(400), 1\43278_2.fw(400), 1\43278_3.fw(400), 1\43278_4.fw(400) Version 2.0.0.1: ID: 390305 / Support ID:400129274 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 392930 / Support ID: 400138511 X2X communication revised A new firmware for hardware variant 3 (BC-Part) was released. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(211), 1\43278_2.fw(211), 1\43278_3.fw(211), 1\43278_4.fw(211) Version 2.0.0.0: ID: 390305 / Support ID: 400129274 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(210), 1\43278_2.fw(210), 1\43278_3.fw(210), 1\43278_4.fw(210) Version 1.3.4.0: ID: 310815 / Support ID: 400097674 POWERLINKV1: Bug-fix for Up/Downgrade POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0 Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 311035 / Support ID: 400051206 Expansion: Link- selector flag New datapoints:<br/>- RedundancyFirstLinkState<br/>- RedundancySecondLinkState Channel description changed: Yes Configuration description changed: Yes Firmware changed: No Firmware:1\43278_1.fw(168), 1\43278_2.fw(168), 1\43278_3.fw(168), 1\43278_4.fw(168) Version 1.3.3.0: ID: 305175 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 305180 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronouscommunication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(167), 1\43278_2.fw(167), 1\43278_3.fw(167), 1\43278_4.fw(167) Version 1.3.2.0: ID: 299000 / Support ID: 400090781 Problem with FW-Update of IO modules on Powerlink buscontrollers The firmware update of IO modules does not work in certain configurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(165), 1\43278_2.fw(165), 1\43278_3.fw(165), 1\43278_4.fw(165) Version 1.3.1.0: ID: 289030 Certain X2X configurationsdon't work In very rare I/O constellations, the X2X modules don't start Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(163), 1\43278_2.fw(163), 1\43278_3.fw(163), 1\43278_4.fw(163) Version 1.3.0.0: ID: 277190 Support of 'Multiple Asynchronous Send' Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 277760 New X2X datapoints - NettimeOffsetX2X and NettimeX2X Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(160), 1\43278_2.fw(160), 1\43278_3.fw(160), 1\43278_4.fw(160) Version 1.2.3.0: ID: 268080 / Support ID: 400072663 Error in FPGA cause a problem inthe MAC effect: causes a losing connection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 268580 New hardware variant New hardware variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(154), 1\43278_2.fw(154), 1\43278_3.fw(154), 1\43278_4.fw(154) Version 1.2.2.0: ID: 246365 DNA support; Update behavior on X2X bus of the BC improved - DNA support (Dynamic Node Allocation) - faster updating of modules with big FW files on the X2X bus of the BC - new objects: 20A3h and 2000h/9 - support for Simulation device added Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(152), 1\43278_2.fw(152), 1\43278_3.fw(152) Version 1.0.3.0: ID: 240470 / Support ID: . Correction of X67BCOnboard Compatible Code Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(144) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.8.0.0 | * | 12/12/2018 | 3 Mo | EXE | AS3.0_HW_X67BC8321.L12.exe | |
| Description |
V3.0 HW Upgrade (X67BC8321.L12) Revision information X67BC8321.L12 Version 2.8.0.0: ID: 619235 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619265 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 621710 Display of further diagnostic data points in the I / O mapping of the X2X interface from the X67 bus controller Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 624315 Firmwareupdate of X2XLink module at POWERLINK Stations does not work since H4.34 Since H4.34 the firmware update of X2XLink modules connected to X67BC8321-1did not work, if they are connected to POWERLINK-Buscontrollers that have no explicit enable for streaming. Problem occurs on BC and SL: X20BC0083 X20cBC0083 < HW-Upgrade 2.2.0.0 X20BC1083 X20cBC1083 < HW-Upgrade 2.5.0.0 X20BC8083 X20cBC8083 < HW-Upgrade 2.5.0.0 X20BC8084 X20cBC8084 < HW-Upgrade 2.5.0.0 X20SL8101 X20cSL8101 X67BC81RT.L12 < HW-Upgrade 2.5.0.0 X67BC8321-1 X67BC8331 X67BC8513.L12 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(426), 1\43278_2.fw(426), 1\43278_3.fw(426), 1\43278_4.fw(426) Version 2.5.5.0: ID: 551150 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(421), 1\43278_2.fw(421), 1\43278_3.fw(421), 1\43278_4.fw(421) Version 2.5.4.0: ID: 540350 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(419), 1\43278_2.fw(419), 1\43278_3.fw(419), 1\43278_4.fw(419) Version 2.5.3.0: ID: 523585 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(417), 1\43278_2.fw(417), 1\43278_3.fw(417), 1\43278_4.fw(417) Version 2.5.2.0: ID: 493935 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(415), 1\43278_2.fw(415), 1\43278_3.fw(415), 1\43278_4.fw(415) Version 2.5.0.0: ID: 468190 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468195 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed:No Configuration description changed: No Firmware changed: Yes ID: 468200 / Support ID: 400178654 Safety modules in connection withPLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468575 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(413), 1\43278_2.fw(413), 1\43278_3.fw(413), 1\43278_4.fw(413) Version 2.2.1.0: ID: 460140 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed:No Configuration description changed: No Firmware changed: Yes ID: 460260 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\43278_1.fw(412), 1\43278_2.fw(412), 1\43278_3.fw(412), 1\43278_4.fw(412) Version 2.1.0.0: ID: 385270 / Support ID: 400132264 hwc, hwx adaption Channel address adapted for fieldbusdesigner Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 439135 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operationalmode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID:439240 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(400), 1\43278_2.fw(400), 1\43278_3.fw(400), 1\43278_4.fw(400) Version 2.0.0.1: ID: 390305/ Support ID: 400129274 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 392930 / Support ID: 400138511 X2X communication revised A new firmware for hardware variant 3 (BC-Part) was released. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(211), 1\43278_2.fw(211), 1\43278_3.fw(211), 1\43278_4.fw(211) Version 2.0.0.0: ID: 390305 / Support ID: 400129274 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(210), 1\43278_2.fw(210), 1\43278_3.fw(210), 1\43278_4.fw(210) Version 1.3.4.0: ID: 310815 / Support ID: 400097674 POWERLINK V1: Bug-fix for Up/Downgrade POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 311035 / Support ID: 400051206 Expansion: Link- selector flag New datapoints:<br/>- RedundancyFirstLinkState<br/>- RedundancySecondLinkState Channel description changed: Yes Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(168), 1\43278_2.fw(168), 1\43278_3.fw(168), 1\43278_4.fw(168) Version 1.3.3.0: ID: 305175 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 305180 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(167), 1\43278_2.fw(167), 1\43278_3.fw(167), 1\43278_4.fw(167) Version 1.3.2.0: ID: 299000 / Support ID: 400090781 Problem with FW-Update of IO modules on Powerlink buscontrollers The firmware update of IO modules does not work in certain configurations. Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\43278_1.fw(165), 1\43278_2.fw(165), 1\43278_3.fw(165), 1\43278_4.fw(165) Version 1.3.1.0: ID: 289030 Certain X2X configurations don't work In very rare I/O constellations, the X2X modules don't start Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(163), 1\43278_2.fw(163), 1\43278_3.fw(163), 1\43278_4.fw(163) Version 1.3.0.0: ID: 277190 Support of 'Multiple Asynchronous Send' Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 277760 New X2X datapoints - NettimeOffsetX2X and NettimeX2X Channel description changed: Yes Configurationdescription changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(160), 1\43278_2.fw(160), 1\43278_3.fw(160), 1\43278_4.fw(160) Version 1.2.3.0: ID: 268080 / Support ID: 400072663 Error in FPGA cause a problem in the MAC effect: causes a losing connection Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 268580 New hardware variant New hardware variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(154), 1\43278_2.fw(154), 1\43278_3.fw(154), 1\43278_4.fw(154) Version 1.2.2.0: ID: 246365 DNA support; Update behavior on X2X bus of the BC improved - DNA support (Dynamic Node Allocation) - faster updating of modules with big FW files on the X2X bus of the BC - new objects: 20A3h and 2000h/9 - support for Simulation device added Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(152), 1\43278_2.fw(152), 1\43278_3.fw(152) Version 1.0.3.0: ID: 240470 / Support ID: . Correction of X67BCOnboard Compatible Code Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(144) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.5.5.0 | * | 08/09/2017 | 3 Mo | EXE | AS3.0_HW_X67BC8321.L12.exe | |
| Description |
V3.0 HW Upgrade (X67BC8321.L12) Revision information X67BC8321.L12 Version 2.5.5.0: ID: 551150 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(421), 1\43278_2.fw(421), 1\43278_3.fw(421), 1\43278_4.fw(421) Version 2.5.4.0: ID: 540350 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(419), 1\43278_2.fw(419), 1\43278_3.fw(419), 1\43278_4.fw(419) Version 2.5.3.0: ID: 523585 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(417), 1\43278_2.fw(417), 1\43278_3.fw(417), 1\43278_4.fw(417) Version 2.5.2.0: ID: 493935 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(415), 1\43278_2.fw(415), 1\43278_3.fw(415), 1\43278_4.fw(415) Version 2.5.0.0: ID: 468190 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468195 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468200 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration descriptionchanged: No Firmware changed: Yes ID: 468575 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(413), 1\43278_2.fw(413), 1\43278_3.fw(413), 1\43278_4.fw(413) Version 2.2.1.0: ID: 460140 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460260 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(412), 1\43278_2.fw(412), 1\43278_3.fw(412), 1\43278_4.fw(412) Version 2.1.0.0: ID:385270 / Support ID: 400132264 hwc, hwx adaption Channel address adapted for fieldbusdesigner Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 439135 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439240 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(400), 1\43278_2.fw(400), 1\43278_3.fw(400), 1\43278_4.fw(400) Version 2.0.0.1: ID: 390305 / Support ID: 400129274 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 392930 / Support ID: 400138511 X2X communication revised A new firmware for hardware variant 3 (BC-Part) was released. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(211), 1\43278_2.fw(211), 1\43278_3.fw(211), 1\43278_4.fw(211) Version 2.0.0.0: ID: 390305 / Support ID: 400129274 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(210), 1\43278_2.fw(210), 1\43278_3.fw(210), 1\43278_4.fw(210) Version 1.3.4.0: ID: 310815/ Support ID: 400097674 POWERLINK V1: Bug-fix for Up/Downgrade POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 311035 / Support ID: 400051206 Expansion: Link- selector flag New datapoints:<br/>- RedundancyFirstLinkState<br/>- RedundancySecondLinkState Channel description changed: Yes Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(168), 1\43278_2.fw(168), 1\43278_3.fw(168), 1\43278_4.fw(168) Version 1.3.3.0: ID: 305175 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 305180 / Support ID: 400094368 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronous communication to the buscontroller wasinterrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\43278_1.fw(167), 1\43278_2.fw(167), 1\43278_3.fw(167), 1\43278_4.fw(167) Version 1.3.2.0: ID: 299000 / Support ID: 400090781 Problem with FW-Update of IO modules on Powerlink buscontrollers The firmware update of IO modules does not work in certain configurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(165), 1\43278_2.fw(165), 1\43278_3.fw(165), 1\43278_4.fw(165) Version 1.3.1.0: ID:289030 Certain X2X configurations don't work In very rare I/O constellations, the X2X modules don't start Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43278_1.fw(163), 1\43278_2.fw(163), 1\43278_3.fw(163), 1\43278_4.fw(163) Version 1.3.0.0: ID: 277190 Support of 'Multiple Asynchronous Send' Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 277760 New X2X datapoints - NettimeOffsetX2X and NettimeX2X Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(160), 1\43278_2.fw(160), 1\43278_3.fw(160), 1\43278_4.fw(160) Version 1.2.3.0: ID: 268080 / Support ID: 400072663 Error in FPGA cause a problem in the MAC effect: causes a losing connection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 268580 New hardware variant New hardware variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\43278_1.fw(154), 1\43278_2.fw(154), 1\43278_3.fw(154), 1\43278_4.fw(154) Version 1.2.2.0: ID: 246365 DNA support; Update behavior onX2X bus of the BC improved - DNA support (Dynamic Node Allocation) - faster updating of modules with big FW files on the X2X bus of the BC -new objects: 20A3h and 2000h/9 - support for Simulation device added Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\43278_1.fw(152), 1\43278_2.fw(152), 1\43278_3.fw(152) Version 1.0.3.0: ID: 240470 / Support ID:. Correction of X67BCOnboard Compatible Code Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\43278_1.fw(144) |
|||||
