DWL@DWL10000114103
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
|---|---|---|---|---|---|---|
| 1.5.0.0 | * | 08/02/2022 | 1 MB | EXE | AS3.0_HW_80PS080X3.10-01.exe | |
| Description |
V3.0 HW Upgrade (80PS080X3.10-01) Revision information 80PS080X3.10-01.10-01 Version 1.5.0.0: ID: 746015 / Support ID: 400351320 Optimization of the control behavior with regenerative power supply in parallel operation Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_3.fw(103), 1\42921_4.fw(103), 1\42921_5.fw(103), 1\42921_6.fw(103), 1\42921_7.fw(103) Version 1.4.0.0: ID: 669195 Short circuit detection configurable Voltage threshold for undervoltage/short-circuit detection at power output Configurable Channel description changed: No Configuration description changed: Yes Firmware changed: Yes ID: 679200 Limitation of voltage at output X2 in case of HW defect Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_3.fw(102), 1\42921_4.fw(102), 1\42921_5.fw(102), 1\42921_6.fw(102), 1\42921_7.fw(102) Version 1.3.0.0: ID: 559755 / Support ID: 400212534 Configured voltage is not output Wrongdoing: It occurs sporadically that the configured output voltage is not output afterstarting the device. The device must be restarted so that the correct voltage is output again. Troubleshooting: Error correction by new firmware. Workaround: Workaround is not possible. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(6), 1\42921_2.fw(7), 1\42921_3.fw(101), 1\42921_4.fw(101), 1\42921_5.fw(101), 1\42921_6.fw(101) Version 1.2.4.0: ID: 421985 Optimization of current controller on Output OUT1 Minimization of ripple currents and voltage ripple for highest load range (about 1000 W) when Uout = 80VDC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(6), 1\42921_2.fw(7), 1\42921_3.fw(100), 1\42921_4.fw(100) Version 1.2.3.0: ID: 332635 / Support ID: 400101160 Optimized control for load alternation and when operated in parallel-mode Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(6), 1\42921_2.fw(7), 1\42921_3.fw(7) Version 1.2.1.1: ID: 312075 Support for the module 80PS080X3.10-01 HW-Variant 3 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 312085 Module bootup timeout configured Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\42921_1.fw(6), 1\42921_2.fw(6), 1\42921_3.fw(6) Version 1.1.1.0: ID: 303185 / Support ID: 400081526 Set overload limit to 120% of nominalpower to be conform with data sheet (for HW-Variant 2) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(4), 1\42921_2.fw(5) Version 1.1.0.0: ID: 280120 Support for the module 80PS080X3.10-01 HW-Variant 2 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 280125 LED blink code for error conditions of OUT1 and OUT2 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 280130 Errors in power calculation for Bleeder temperature model Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 280135 Function model "CANIOBusController" Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\42921_1.fw(3), 1\42921_2.fw(3) Version 1.0.1.0: ID: 250855 / Support ID: 400060553 80PS080X3 - Additional 24 VDC output problems Output Voltage of 24 VDC not constant. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(2) Version1.0.0.0: ID: 235255 Support for the module 80PS080X3.10-01 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\42921_1.fw(1) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 1.3.0.0 | * | 10/11/2017 | 3 MB | EXE | AS3.0_HW_80PS080X3.10-01.exe | |
| Description |
V3.0 HW Upgrade (80PS080X3.10-01) Revision information 80PS080X3.10-01 Version 1.3.0.0: ID: 559755 / Support ID: 400212534 Configured voltage is not output Wrongdoing: It occurs sporadically that the configured output voltage is not output afterstarting the device. The device must be restarted so that the correct voltage is output again. Troubleshooting: Error correction by new firmware. Workaround: Workaround is not possible. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(6), 1\42921_2.fw(7), 1\42921_3.fw(101), 1\42921_4.fw(101), 1\42921_5.fw(101), 1\42921_6.fw(101) Version 1.2.4.0: ID: 421985 Optimization of current controller on Output OUT1 Minimization of ripple currentsand voltage ripple for highest load range (about 1000 W) when Uout = 80VDC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(6), 1\42921_2.fw(7), 1\42921_3.fw(100), 1\42921_4.fw(100) Version 1.2.3.0: ID: 332635 / Support ID: 400101160 Optimized control for load alternation and whenoperated in parallel-mode Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(6), 1\42921_2.fw(7), 1\42921_3.fw(7) Version 1.2.1.1: ID: 312075 Support for the module 80PS080X3.10-01 HW-Variant 3 Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 312085 Module bootup timeout configured Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\42921_1.fw(6), 1\42921_2.fw(6), 1\42921_3.fw(6) Version 1.1.1.0: ID: 303185 / Support ID: 400081526 Set overload limit to 120% of nominal power to be conform with data sheet (for HW-Variant 2) Channel description changed: No Configurationdescription changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(4), 1\42921_2.fw(5) Version 1.1.0.0: ID: 280120 Supportfor the module 80PS080X3.10-01 HW-Variant 2 Channel description changed:No Configuration description changed: No Firmware changed: No ID: 280125 LED blink code for error conditions of OUT1 and OUT2 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 280130 Errors in power calculation for Bleeder temperature model Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 280135 Function model "CANIOBusController" Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\42921_1.fw(3), 1\42921_2.fw(3) Version 1.0.1.0: ID:250855 / Support ID: 400060553 80PS080X3 - Additional 24 VDC output problems Output Voltage of 24 VDC not constant. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(2) Version 1.0.0.0: ID: 235255 Support for the module 80PS080X3.10-01 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\42921_1.fw(1) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 1.2.3.0 | * | 28/03/2013 | 12 MB | EXE | AS3.0_HW_80PS080X3.10-01.exe | |
| Description |
V3.0 HW Upgrade (80PS080X3.10-01) Revision information 80PS080X3.10-01 Version 1.2.3.0: ID: 332635 / Support ID: 400101160 Optimized control for load alternation and when operated in parallel-mode Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(6), 1\42921_2.fw(7), 1\42921_3.fw(7) Version 1.2.1.1: ID: 312075 Support for the module 80PS080X3.10-01 HW-Variant 3 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 312085 Module bootup timeout configured Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\42921_1.fw(6), 1\42921_2.fw(6), 1\42921_3.fw(6) Version 1.1.1.0: ID: 303185 / Support ID: 400081526 Set overload limit to 120% of nominal power to be conform with data sheet (for HW-Variant 2) Channeldescription changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(4), 1\42921_2.fw(5) Version 1.1.0.0: ID: 280120 Support for the module 80PS080X3.10-01 HW-Variant 2 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 280125 LED blink code for error conditions of OUT1 and OUT2 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 280130 Errors in power calculation for Bleeder temperature model Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 280135 Function model "CANIOBusController" Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\42921_1.fw(3), 1\42921_2.fw(3) Version 1.0.1.0: ID: 250855 / Support ID: 400060553 80PS080X3 - Additional 24 VDC output problems Output Voltage of 24 VDC not constant. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42921_1.fw(2) Version 1.0.0.0: ID: 235255 Support for the module 80PS080X3.10-01 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\42921_1.fw(1) |
|||||
