80MPD1.300S014-01

Short description

Stepper motor	Stepper motor flange size 56.4 mm, length 66 mm, incremental encoder

General information

Certifications
CE	Yes
UKCA	Yes
CRA (Cyber Resilience Act)	Not applicable

Specific motor data

Wiring	Serial
Current	3 A
Resistance/Phase	1.2 Ω
Inductance/Phase	3.6 mH
Stall torque	0.8 Nm
Holding torque	1.1 Nm
Detent torque	<30 mNm
Rotor inertia	Approx. 145 gcm²

General motor data

Stepping angle	1.8°
Max. surface temperature	95°C
Average period of operation between failures	21,000 hours
Shaft type	Flat-sided shaft (D-cut)
Insulation class	B (130°C)
Insulation resistance	100 MΩ min. 500 VDC
Dielectric resistance	500 VAC for 1 minute
Driver supply voltage	Max. 80 VDC

Operating conditions

Degree of protection per EN 60529	IP20

Ambient conditions

Temperature
Operation	-20 to 40°C
Storage	-30 to 85°C
Transport	-30 to 85°C
Relative humidity
Operation	5 to 95%, non-condensing
Storage	5 to 95%, non-condensing
Transport	5 to 95%, non-condensing

Electrical properties - Encoder

Number of outputs	3 A / B / R
Resolution	1024 increments / 256 positions per rotation
Output circuit	Push/Pull level, asymmetrical
Output protection	Protection against short circuit
Current consumption	Max. 12 mA + Output load
Supply voltage	18 to 30 VDC
Max. output current	±10 mA per output

Mechanical properties

Max. radial load	73.5 N
Max. axial load	The permissible axial load is not permitted to be greater than the motor mass.
Weight	550 g
Length	66 mm

Número do material:

80MPD1.300S014-01

Descrição:

2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque

Acessórios opcionais

Accessories

80XMPXAC0.00-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque

Hybrid cables

80CM01013.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM02013.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM03013.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM05013.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM10013.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM15013.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM25013.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque

Incremental encoder cables

80CM00703.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM01003.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM01703.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM02003.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM03003.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM05003.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM07503.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM10003.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM15003.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM20003.25-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque

Motor cables

80CM01001.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM01501.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM02001.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM03001.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM05001.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM10001.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM15001.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque
80CM20001.21-01	2-phase hybrid stepper motor, 56.4 mm flange, length 66 mm, ABR 24 VDC, 3 A series, 1.1 Nm holding torque, 0.8 Nm stall torque

Certificados	Version (Data)	Download
EU Declaration Motors Hybrid		PDF / 166 KB Login for download
UK Declaration Motors Hybrid		PDF / 135 KB Login for download

Documentação	Version (Data)	Download
Stepper motors user's manual		PDF / 49 MB Login for download