DWL@DWL10000878263
| 仕様版 | 言語 | オペレーティングシステム | 日付 | サイズ | タイプ | ダウンロード |
|---|---|---|---|---|---|---|
| 1.4.1.1 | * | 2026/10/07 | 2 MB | EXE | AS6_HW_X20IF1041-1.exe | |
| 説明 |
V6.0 HW Upgrade (X20IF1041-1) Revision information X20IF1041-1 Version 1.4.1.1: ID: Firmware signature enables automatic verification of the authenticity on the target system The firmware package contains a digital signature that is automatically validated by Automation Runtime versions, which are supporting this feature. Thisensures that the installedfirmware is unchanged and comes from a trusted source. Channel description changed: no Configuration description changed: yes Firmware changed: no Version 1.4.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration descriptionchanged: yes Firmware changed: no Version 1.3.0.0: ID: 482990 Module documentation revised Data sheet V2.03 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 627865 Replacement of the interfacecard in AS "Replace HW Modul" works correktly Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 717095 New FW V2.14.0.3_29 SDO and PDO transfer possible immediately after ModulOK = TRUE Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42761a1.fw(29), 1\42761_1.fw(13) Version 1.2.1.0: ID: 466580 FDT/DTM Cycle Time change Change parameter name "Cycle time [µs]" to "Data exchange time (CPU-netX) [µs]" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 466585 Add ModulOK in I/O Mapping Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12) Version 1.2.0.0: ID: 459055 X20IF1061-1: NetX: Cyclic statusbits wrong when cable is disconnected Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\42761a1.fw(27), 1\42761_1.fw(12) Version 1.1.3.0: ID: 422290 Wrong SDO handling causes in rarecases stop of the Interface card. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\42761a1.fw(25), 1\42761_1.fw(12) Version 1.1.2.0: ID: 263655 Incorrect error message when writing SDOs If an SDO write request on the CAN bus returns error message 0x08000024 (noaccess to flash memory), then this is not received in this form in the nxcomSdoWrite() function block. The nxcomSdoWrite() function incorrectly returns error message 0xC0420028 (general fault during SDO transfer). Channel description changed: No Configuration description changed: No Firmware changed: No ID: 376165 Frequent transmission of Start command by nxcomNmt function block causing aproblem in mailbox or master Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42761a1.fw(24), 1\42761_1.fw(12) Version 1.1.1.1: ID: 366170 EPLAN-datas got conformed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\42761a1.fw(22), 1\42761_1.fw(12) Version 1.1.0.3: ID: 263645 CANopen master doesn't write output data to all slaves When using a special configuration with several CANopen slaves the output data is only written to the first slave. Channel description changed: No Configurationdescription changed: No Firmware changed: Yes Firmware: 1\42761a1.fw(21), 1\42761_1.fw(12) Version 1.1.0.1: ID: 259320 Vendor ID changed Module identifies with B+R Vendor ID now Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42761a1.fw(20), 1\42761_1.fw(12) Version 1.0.3.0: ID: 240405 X20 Interface CANopen Master, Configuration of netX cycle time X20 Interface CANopen Master, Configuration of netX cycletime. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12) Version 1.0.2.0: ID: 239395 Interface module CANopen master: Output data not written by all CANopen slaves Interface module CANopen master: Output data not written by all CANopen slaves Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42761a1.fw(18), 1\42761_1.fw(12) Version 1.0.1.0: ID: 235825 Interface module CANopen master, first version Interface module CANopen master, first version Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\42761a1.fw(17), 1\42761_1.fw(12) |
|||||
