General information
B&R ID code 0xDD94
Support
Dynamic node allocation (DNA) Yes
Cooling and mounting type Cold plate or pass-through mounting
Certifications
CE Yes
UKCA Yes
UL cULus E225616
Power conversion equipment
EAC Yes
Mains connection
Network configurations TT, TN-S, TN-C-S
Mains input voltage 3x 208 to 3x 480 VAC ±10%
Frequency 50 / 60 Hz ±4%
Installed load Max. 6.7 kVA
Power dissipation with continuous power [2.8 * P² + 0.5 * P + 10] W
Inrush current at 400 VAC 2 A
Switch-on interval >120 s
Max. DC bus capacitance depending on mains voltage
230 VAC 9 mF
400 VAC 3 mF
480 VAC 2 mF
Integrated line filter per EN 61800-3, category C3 Yes
Integrated regeneration choke No
Regenerative No
Power factor correction (PFC) No
Variant
L1, L2, L3, PE Connector
PE M5 threaded bolt
Shield connection No
Terminal connection cross section
Flexible and fine-stranded wires
With wire end sleeves 0.5 to 6 mm²
Approbation data
UL/C-UL-US 20 to 6 AWG
CSA 20 to 6 AWG
Terminal cable cross section dimension of shield connection 23 to 35 mm
DC bus connection
Voltage
Nominal 294 to 679 VDC
Continuous power 4 kW
Reduction of continuous power depending on mains input voltage
Mains input voltage <3x 400 VAC 10 W/V * (400 V - Mains input voltage)
Reduction of continuous power depending on installation elevation
Starting at 500 m above sea level 0.4 kW per 1000 m
Reduction of continuous power depending on cooling method No reduction
Peak power output (supply) 12 kW
DC bus capacitance 330 µF
Protective measures
Overload protection Yes
Short-circuit and ground fault protection No
Variant ACOPOSmulti backplane
24 VDC power supply
Input voltage 25 VDC ±1.6%
Input capacitance 23.5 µF
Max. power consumption 12 W
Variant ACOPOSmulti backplane
24 VDC In
Input voltage
Minimum 18 VDC
Nominal 24 VDC
Maximum 30 VDC
24 VDC internal system power supply 25 VDC ±1.6% (regulated)
Switch-on threshold 16 V
Max. continuous current 4.0 A
Status indicators 24 V LED
Undervoltage detection Yes
Overvoltage detection Yes
Protective measures
No-load proof Yes
Overload-proof Yes
Short-circuit proof Yes
Overtemperature protection Yes
Variant
24 VDC In, COM Connector
Terminal connection cross section of input "24 VDC In"
Flexible and fine-stranded wires
With wire end sleeves 0.2 to 2.5 mm²
Approbation data
UL/C-UL-US 30 to 12 AWG
CSA 22 to 12 AWG
Braking resistor
Peak power int./ext. 2 kW / 24 kW (max. 1 s)
Continuous power int./ext. 150 W / 8 kW
Min. braking resistance 25 Ω
Rated current of built-in fuse 15 A (fast-acting)
Variant
RB+, RB-, PE Connector
Shield connection Yes
Terminal connection cross section
Flexible and fine-stranded wires
With wire end sleeves 0.5 to 6 mm²
Approbation data
UL/C-UL-US 20 to 6 AWG
CSA 20 to 6 AWG
Terminal cable cross section dimension of shield connection 23 to 35 mm
Protective measures
Overload protection Yes
Short-circuit and ground fault protection Yes (with RB+ by externally replaceable melting fuse)
Electrical properties
Discharge capacitance 0.4 µF
Operating conditions
Permissible mounting orientations
Hanging vertically Yes
Horizontal, face up Yes
Standing horizontally No
Installation elevation above sea level
Nominal 0 to 500 m
Maximum 4000 m
Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
Overvoltage category per EN 61800-5-1 III
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Nominal 5 to 40°C
Maximum 55°C
Storage -25 to 55°C
Transport -25 to 70°C
Relative humidity
Operation 5 to 85%
Storage 5 to 95%
Transport Max. 95% at 40°C
Mechanical properties
Dimensions
Width 53.5 mm
Height 317 mm
Depth
Cold plate 212 mm
Pass-through mounting 209 mm
Weight 3.5 kg
Module width 1
Номер модель:
8B0P0110HC00.000-1
Описание:

Passive power supply modules act as the central power supply for ACOPOSmulti drives and feed the DC bus. They are not subjected to a control loop and therefore cannot provide regeneration.

The 8B0P0110HC00.000-1 passive power supply module has an integrated line filter and internal braking resistor. It is also possible to connect an optional external braking resistor. In addition, an interface for connecting 24 VDC is also available. This allows the internal 24 VDC supply to provide an ACOPOSmulti drive system with up to 90 watts of nominal power. This eliminates the need for an 8B0C auxiliary supply module in many applications. The system can start either from external 24 VDC or mains power.

ACOPOSmulti power supply module, passive, 11 A, AS, cold plate or pass-through mounting, 24 V In 1x, integrated line filter
Обязательные аксессуары
Terminal block sets
8BZ0P011000.000-1A Screw clamp terminal block set for ACOPOSmulti 8B0P0110Hx00.00x-1 modules: 1x 8TB3104.206F-10, 1x 8TB3103.202A-10, 1x 8TB2106.2010-00
Дополнительные аксессуары
Braking resistors
8B0W0045H000.000-1 Braking resistor, 450 W, 50 R, IP20, terminals
8B0W0045H000.001-1 Braking resistor, 450 W, 50 R, IP65, terminals
8B0W0079H000.000-1 Braking resistor, 790 W, 33 R, IP20, terminals
8B0W0079H000.001-1 Braking resistor, 790 W, 33 R, IP65, terminals
Fan modules
8BXF001.0000-00 Модуль вентилятора для ACOPOSmulti, сменный вентилятор для модулей ACOPOSmulti (8BxP/8B0C/8BVI/8BVE/8B0K)
POWERLINK/Ethernet cables
X20CA0E61.00020 Соединительный кабель POWERLINK/Ethernet, RJ45 – RJ45, длина 0,2 м
X20CA0E61.00025 Соединительный кабель POWERLINK, RJ45 – RJ45, 0,25 м
X20CA0E61.00030 Соединительный кабель POWERLINK, RJ45 – RJ45, 0,3 м
X20CA0E61.00035 Соединительный кабель POWERLINK, RJ45 – RJ45, 0,35 м
X20CA0E61.00050 Соединительный кабель POWERLINK/Ethernet, RJ45 – RJ45, длина 0,5 м
X20CA0E61.00100 Соединительный кабель POWERLINK/Ethernet, RJ45 – RJ45, длина 1 м
Shield component sets
8SCS000.0000-00 Набор компонентов для экранирования ACOPOSmulti: 1 пластина для крепления экрана 1x тип 0, 1 хомут для кабеля, B 9 мм, D 12-22 мм
8SCS002.0000-00 Набор компонентов для экранирования ACOPOSmulti: 1 зажимная планка, 2 хомута D 4-13,5 мм, 2 винта
8SCS009.0000-00 Набор компонентов для экранирования ACOPOSmulti: 1 пластина для крепления экрана ACOPOSmulti SK8-14, 1 зажим для крепления экрана SK14
8SCS010.0000-00 Набор компонентов для экранирования ACOPOSmulti: 1 пластина для крепления экрана ACOPOSmulti SK14-20, 1 зажим для крепления экрана SK20
Terminal blocks
8TB2106.2010-00 6-pin screw clamp terminal block, 1-row, pitch: 5.08 mm, label 1: Numbered consecutively
8TB3103.202A-10 3-pin screw clamp terminal block, 1-row, pitch: 7.62 mm, label 2: PE RB- RB+, coding A: 000
8TB3104.206F-10 4-pin screw clamp terminal block, 1-row, pitch: 7.62 mm, label 6: PE L3 L2 L1, coding L: 0101
E-CAD (Electro или EPLAN шаблоны) Версия (Дата) Загрузка
ACOPOSmulti EPLAN P8 from V2.4 EXE / 81 МБ
M-CAD (Механические Шаблоны Версия (Дата) Загрузка
3D file STEP 8B0P0110HC00.000-1 ZIP / 115 кБ
Документация Версия (Дата) Загрузка
ACOPOSmulti User´s Manual PDF / 302 МБ
Datasheet 8B0P0110HC00.000-1 PDF / 2 МБ
Обновление Automation Studio HW Версия (Дата) Загрузка
V4.0 HW Upgrade (8B0P0110HC00.000-1) EXE / 254 кБ
V4.0 HW Upgrade (8B0Pxxxxxxxx.xxx-1) EXE / 676 кБ
V4.0 HW Upgrade (8B0Pxxxxxxxx.xxx-x) EXE / 517 кБ
Сертификаты Версия (Дата) Загрузка
E225616 UL Certificate of Compliance ACOPOSmulti (UL 508C) PDF / 282 кБ
E225616 UL Certificate of Compliance ACOPOSmulti (UL 61800-5-1) PDF / 183 кБ
EAC Conformity declaration 8B power sources PDF / 1 МБ
EU Declaration Servos ACOPOSmulti PDF / 219 кБ
UK Declaration Servos ACOPOSmulti PDF / 109 кБ

Укажите страну и язык

B&R Logo