DWL@DWL10000300344
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
|---|---|---|---|---|---|---|
| 1.10.13.0 | * | 20.03.2024 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.13.0: ID: 780195 Correction of the input filter with set "Filter off". Correction of the input filter, if a "Filter off" is set and a channel error is detected. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42916_1.fw(340) Version 1.10.12.0: ID: 710630 Timing of module internal communication updated The timing of the module internal communication was updated. Sporadic errors 98818, 119317, 99348, 102914, 99350 no longer occur. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 710795 Limit values for the module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42916_1.fw(333) Version 1.10.11.0: ID: 692690 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692590 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42916_1.fw(332) Version 1.10.10.2: ID: 669890 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.1: ID: 643305 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.0: ID: 621345 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 622110 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in the OSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2 safety processors to reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.12.0 | * | 16.04.2021 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.12.0: ID: 710630 Timing of module internal communication updated The timing of the module internal communication was updated. Sporadic errors 98818, 119317, 99348, 102914, 99350 no longer occur. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 710795 Limit values for the module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42916_1.fw(333) Version 1.10.11.0: ID: 692690 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692590 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42916_1.fw(332) Version 1.10.10.2: ID: 669890 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.1: ID: 643305 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.0: ID: 621345 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 622110 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in the OSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2 safety processors to reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.11.0 | * | 17.09.2020 | 2 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.11.0: ID: 692690 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692590 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42916_1.fw(332) Version 1.10.10.2: ID: 669890 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.1: ID: 643305 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.0: ID: 621345 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 622110 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in the OSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2 safety processors to reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.10.2 | * | 31.01.2020 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.10.2: ID: 669890 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.1: ID: 643305 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.0: ID: 621345 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 622110 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in the OSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2 safety processors to reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.10.1 | * | 16.05.2019 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.10.1: ID: 643305 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response timehas been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.10.0: ID:621345 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 622110 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in the OSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is notmapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration descriptionchanged: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmwarechanged: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel descriptionchanged: No Configuration description changed: No Firmware changed:No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module alsosupports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Supportof AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level"Info" or "Warning" are sent by only 1 of the 2 safety processors to reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy timeerror message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.10.0 | * | 06.12.2018 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.10.0: ID: 621345 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configurationdescription changed: No Firmware changed: Yes ID: 622110 / Support ID: 400269002 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(331) Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the descriptionsection in the OSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "DiscrepancyTime" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed:No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible toset SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModuleIDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration filerelease 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID:290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameterfor backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release forSafety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2safety processors to reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration descriptionchanged: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.9.0 | * | 08.11.2018 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.9.0: ID: 618220 logger entry 112174, 108078 Loggerentry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(330) Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in theOSDD files Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration descriptionchanged: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configurationdescription changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channeldescription changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, themodule also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed:No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2safety processorsto reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration descriptionchanged: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.1.0 | * | 19.03.2018 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.1.0: ID: 541505 Improve the description section in the OSDD files Improve the description section in the OSDD files Channeldescription changed: No Configuration description changed: Yes Firmware changed: No ID: 541665 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549940 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 570615 / Support ID: 400236267 set SafeOutputOKs even when channel is not mapped SafeOutputOKs are set now even when channel is not mapped Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(325) Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrizationof timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425465 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2safety processors to reduce the number ofmessages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.0.6 | * | 04.10.2017 | 3 MB | EXE | AS4_HW_X20SC2432.exe | |
| Popis |
V4.0 HW Upgrade (X20SC2432) Revision information X20SC2432 Version 1.10.0.6: ID: 486445 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 533005 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533090 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmwarechanged: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.2: ID: 483055 Added coated type of module in help Added coated type of module in help Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.10.0.1: ID: 470510 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470515 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301), 7\42916_1.fw(320) Version 1.9.1.0: ID: 425445 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425460 Update Online Help Update Online Help V1.91 Channel description changed: No Configurationdescription changed: No Firmware changed: No ID: 425465 fwvalid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 6\42916_1.fw(301) Version 1.9.0.0: ID: 243055 / Support ID: 400054331 DXF-File ready to be downloaded DXF-File ready to be downloaded Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413815 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described inthe AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 413920 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414320 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290), 5\42916_1.fw(300) Version 1.6.0.8: ID: 388340 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed:No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.7: ID: 339225 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.5: ID: 335320 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335325 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.6.0.0: ID: 314295 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.4: ID: 303355 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.5.0.3: ID: 287440 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290260 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282), 4\42916_1.fw(290) Version 1.4.1.3: ID: 284650 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.1.1: ID: 272230 Release for Safety Release 1.5 Release for Safety Release 1.5 Channel description changed:No Configuration description changed: No Firmware changed: No Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.4.0.1: ID: 225435 Safety Release 1.4 - SI: one can configure the channel that shall be used as pulse source for testpulse with mode "internal" (see manual) - different levels for logger entires: "Info", "Warning" or "Error" (AR B3.05 required) - logger entries with level "Info" or "Warning" are sent by only 1 of the 2safety processors to reduce the number of messages - X2X diagnostics data points (AR 3.08 required) Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 2\42916_1.fw(272), 3\42916_1.fw(282) Version 1.2.1.0: ID: 219630 erroneous discrepancy time error message An erroneous discrepancy time error message could be generated at startup by the 2 channel evaluation if external devices are used that generate test pulses. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42916_1.fw(272) Version 1.2.0.3: ID: 213430 changes in HWC fixed typos of safety parameters enabled for AR B2.96 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42916_1.fw(271) Version 1.2.0.0: ID: 212845 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware:2\42916_1.fw(272), 3\42916_1.fw(282) |
|||||
