DWL@DWL10000344431
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
|---|---|---|---|---|---|---|
| 1.11.0.0 | * | 20.07.2023 | 3 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20CP3586 Version 1.11.0.0: ID: 772740 / Support ID: 400400350, 400406359, 400407650 Wrong power consumption data corrected: calculated values in AS did notmatch to correct documentation Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(142) Version 1.10.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration description changed: yes Firmware changed: no Version 1.9.0.1: ID: 709895 Test Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(142) Version 1.9.0.0: ID: 691740 / Support ID: 400325418 POWERLINK: Operating mode "Ethernet" If a POWERLINK interface was operated in operating mode "Ethernet" andconnected to a POWERLINK network in this mode, the interface could fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(142) Version 1.8.1.0: ID: 664845 Support data point StorageWear, wear level of storage medium starting fromAR A4.90 Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 694590 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(141) Version 1.8.0.0: ID: 652280 POWERLINK: Possible failure of already configured CNs if new "chained stations" added during operation Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 652445 Error correction: DNA tree topologies not always started up correctly Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(141) Version 1.6.0.0: ID: 635430 Module documentation revised Data sheet V1.52 Channel description changed: No Configuration description changed:No Firmware changed: No ID: 635555 POWERLINK-Manager: Withfrequent failure of CN's, which are operated with the optimization "Chained station" it can be happen that failed CN's were not longer adressed by the manager. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(138) Version 1.5.0.0: ID: 542445 Changing the position of "Temperature data type configuration" in the CPU configuration Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 590110 X20CPx58x: I/O Datapoints "SupplyVoltage" and "SupplyCurrent" for onboard PS module Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 590125 Module documentation revised Data sheet V1.39 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 603380 / Support ID: 400250890 POWERLINK CNs with configuration "Optimization: Minimal latency": No input data received POWERLINK CNs with configuration "Optimization: Minimal latency"and "Chained station: On" that are not physically present in the network can cause no input data to be received from all CNs with setting "Optimization: Minimal latency". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17),1\48939a0.epl(136) Version 1.4.2.0: ID: 536520 / Support ID: 400204420 POWERLINK V2: no asynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(131) Version1.4.0.0: ID: 497865 Configurable negative temperature display range Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters when replacing the CPU Channeldescription changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.3.0.0: ID: 462610 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462710 Update online help Channel descriptionchanged: No Configuration description changed: No Firmware changed:No ID: 462800 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462875 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.2.0.0: ID: 443705 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445135 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(15), 1\48939a0.epl(128) Version 1.1.1.0: ID: 434150 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(15), 1\48939a0.epl(127) Version 1.1.0.0: ID: 380887 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 386680 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413270 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping outof an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417160 EnhancementECAD data Channel description changed: No Configuration descriptionchanged: Yes Firmware changed: No ID: 417235 Support of Poll Response Chaining on iCN Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417430 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423325 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\48939_0.pci(15), 1\48939a0.epl(127) Version 1.0.4.0: ID: 344995 / Support ID: - POWERLINK V1 MN mode: "Nettime SoC" is not increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 345645 POWERLINK V1 MN mode Error correction: Cyclic input data and net time togglebetween the last tworeceived values when CNs drop out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 359040 POWERLINK MN mode: If "Multiplexing prescale" >= 9, then the input data of the multiplexed stations that were configured in the last "network cycle" were not transferred in certain configurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 359285 / Support ID: 400113446 POWERLINK V2 MN mode: Asynchronous connection losses may occur as a result of high asynchronous loads on the POWERLINK network and high loads on the CPU. This could maintain you to an error 32205 Timeout while writing par.via acyclic channel. Channel description changed: No Configuration description changed: No Firmware changed: Yes Version 1.0.3.0: ID: 338595 / Support ID: 400113132 Half-duplex Ethernet connectionsare not detected when using "Ethernet" operating mode with baud rate "100 MBit auto". This reduces total data throughput. Channel description changed:No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(123) Version 1.0.2.0: ID: 332415 / Support ID: 400092134 POWERLINK V1: If the "Activate Ethernet communication off" option is enabled, asynchronous POWERLINK communication fails in some circumstances. The following configuration may cause asynchronous communication to fail: - POWERLINK V1 - "Activate Ethernetcommunication off" - POWERLINK CNs on the network that also support POWERLINK V2 This upgrade can be installed to resolve this problem. It is also possible toset "Activate Ethernet communication" to "On". Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 336755 POWERLINK V2 MN mode: It was possible that an undefined state occurred during booting that causedthe interface tofail. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 337480 / Support ID: 400108118 POWERLINK V2 CN mode It was possible that an undefined state occurred during booting that causedthe interface to fail. Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(120) Version 1.0.1.4: ID: 307295 Enhancement English online-help and error corrections Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(11), 1\48939a0.epl(117) Version 1.0.1.3: ID: 285165 Support X20CP3586 First Version Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(117) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.0.0 | * | 23.07.2021 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20CP3586 Version 1.10.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration description changed: yes Firmware changed: no Version 1.9.0.1: ID: 709895 Test Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(142) Version 1.9.0.0: ID: 691740 / Support ID: 400325418 POWERLINK: Operating mode "Ethernet" If a POWERLINK interface was operated in operating mode "Ethernet" and connected to a POWERLINK network in this mode,the interface could fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(142) Version 1.8.1.0: ID: 664845 Support data point StorageWear, wear level of storage medium starting fromAR A4.90 Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 694590 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(141) Version 1.8.0.0: ID: 652280 POWERLINK: Possible failure of already configured CNs if new "chained stations" added during operation Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 652445 Error correction: DNA tree topologies not always started up correctly Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(141) Version 1.6.0.0: ID: 635430 Module documentation revised Data sheet V1.52 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 635555 POWERLINK-Manager: With frequent failure of CN's, which are operated with the optimization "Chained station" it can be happen that failed CN's were not longer adressed by the manager. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(138) Version 1.5.0.0: ID: 542445 Changing the position of "Temperature data type configuration" in the CPU configuration Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 590110 X20CPx58x: I/O Datapoints "SupplyVoltage" and "SupplyCurrent" for onboard PS module Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 590125 Module documentation revised Data sheet V1.39 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 603380 / Support ID: 400250890 POWERLINK CNs with configuration "Optimization: Minimal latency": No input data received POWERLINK CNs with configuration "Optimization: Minimal latency" and "Chained station: On" that are not physically present in the network can cause no input data to be received from all CNswith setting "Optimization: Minimal latency". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(136) Version 1.4.2.0: ID: 536520 / Support ID: 400204420 POWERLINK V2: no asynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(131) Version 1.4.0.0: ID: 497865 Configurablenegative temperature display range Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID:520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters whenreplacing the CPU Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.3.0.0: ID: 462610 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462710 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 462800 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462875 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.2.0.0: ID: 443705 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445135 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(15), 1\48939a0.epl(128) Version 1.1.1.0: ID: 434150 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(15), 1\48939a0.epl(127) Version 1.1.0.0: ID: 380887 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 386680 Documentation: enhancementsand corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413270 / Support ID:400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417160 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417235 Support of Poll Response Chaining on iCN Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417430 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423325 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(15), 1\48939a0.epl(127) Version 1.0.4.0: ID: 344995 / Support ID: - POWERLINK V1 MN mode: "Nettime SoC" is not increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 345645 POWERLINK V1 MN mode Error correction: Cyclicinput data and net time toggle between the last tworeceived values when CNs drop out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 359040 POWERLINK MN mode: If "Multiplexing prescale" >= 9, then the input data of the multiplexed stations that were configured in the last "network cycle" were not transferred in certain configurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 359285 / Support ID: 400113446 POWERLINK V2 MN mode: Asynchronous connection losses may occur as a result of high asynchronous loads on the POWERLINK network and high loads on the CPU. This could maintain you to an error 32205 Timeout while writing par. via acyclic channel. Channel description changed: No Configuration description changed: No Firmware changed: Yes Version 1.0.3.0: ID: 338595 / Support ID: 400113132 Half-duplex Ethernet connections are not detected when using "Ethernet" operating mode with baud rate "100 MBit auto". This reduces total data throughput. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(123) Version 1.0.2.0: ID: 332415 / Support ID: 400092134 POWERLINK V1: If the "Activate Ethernet communication off" option is enabled, asynchronous POWERLINK communication fails in some circumstances. The following configuration may cause asynchronous communication to fail: - POWERLINK V1 - "Activate Ethernet communication off" - POWERLINK CNs on the network that also support POWERLINK V2 This upgrade can be installed to resolve this problem. It is also possible toset "Activate Ethernet communication" to "On". Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 336755 POWERLINK V2 MN mode: It was possible that an undefined state occurred during booting that causedthe interface to fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 337480 / Support ID: 400108118 POWERLINK V2 CN mode It was possible that an undefined state occurred during booting that causedthe interface tofail. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(120) Version 1.0.1.4: ID: 307295 Enhancement English online-help and error corrections Channel description changed: No Configuration description changed: No Firmware changed: No Firmware:1\48939_0.pci(11), 1\48939a0.epl(117) Version 1.0.1.3: ID: 285165 Support X20CP3586 First Version Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(117) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.9.0.0 | * | 04.11.2020 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20cCP1584 Version 1.9.0.0: ID: 691740 / Support ID: 400325418 POWERLINK: Operating mode "Ethernet" If a POWERLINK interface was operated in operating mode "Ethernet" and connected to a POWERLINK network in this mode, the interface could fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(142) Version 1.8.1.0: ID: 664845 Support data point StorageWear, wear level of storage medium starting fromAR A4.90 Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 694590 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(141) Version 1.8.0.0: ID: 652280 POWERLINK: Possible failure of already configured CNs if new "chained stations" added during operation Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 652445 Error correction: DNA tree topologies not always started up correctly Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(141) Version 1.6.0.0: ID: 635430 Module documentation revised Data sheet V1.52 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 635555 POWERLINK-Manager: With frequent failure of CN's, which are operated with the optimization "Chained station" it can be happen that failed CN's were not longer adressed by the manager. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(138) Version 1.5.0.0: ID: 542445 Changing the position of "Temperature data type configuration" in the CPU configuration Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 590110 X20CPx58x: I/O Datapoints "SupplyVoltage" and "SupplyCurrent" for onboard PS module Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 590125 Module documentation revised Data sheet V1.39 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 603380 / Support ID: 400250890 POWERLINK CNs with configuration "Optimization: Minimal latency": No input data received POWERLINK CNs with configuration "Optimization: Minimal latency" and "Chained station: On" that are not physically present in the network can cause no input data to be received from all CNs with setting "Optimization: Minimal latency". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\57883_0.pci(17), 1\57883a0.epl(136) Version 1.4.2.0: ID: 537770 / Support ID: 400204420 POWERLINK V2: no asynchronous frames in modeNMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(131) Version 1.4.0.0: ID: 497865 Configurable negative temperature display range Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters when replacing the CPU Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.0.0: ID: 462620 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462640 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 462725 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID:462805 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.2.0.0: ID: 443655 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445140 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(15), 1\57883a0.epl(128) Version 1.1.0.0: ID: 417225 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417310 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417365 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 417495 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423920 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424035 / Support ID: 400150240 POWERLINK V2: "Controlled node"mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(15), 1\57883a0.epl(127) Version1.0.1.1: ID: 391690 / Support ID: 400137793 Correction terminalmode Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.1.0: ID: 388285 / Support ID: 0 Sporadic error when starting the onboard POWERLINK interface corrected Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.0.1: ID: 311570 Support X20cCP1584 Enhancementonline-help Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(12), 1\57883a0.epl(123) Version 1.0.0.0: ID: 311570 Support X20cCP1584 First version Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(11), 1\57883a0.epl(121) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.8.1.0 | * | 20.08.2020 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20cCP1584 Version 1.8.1.0: ID: 664845 Support data point StorageWear, wear level of storage medium starting fromAR A4.90 Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 694590 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(141) Version 1.8.0.0: ID: 652280 POWERLINK: Possible failureof already configured CNs if new "chained stations" added during operation Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 652445 Error correction: DNA treetopologies not always started up correctly Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(141) Version 1.6.0.0: ID: 635430 Module documentation revised Data sheet V1.52 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 635555 POWERLINK-Manager: With frequent failure of CN's, which are operated with the optimization "Chained station" itcan be happen that failed CN's were not longer adressed by the manager. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(138) Version 1.5.0.0: ID: 542445 Changing the position of "Temperature data type configuration" in the CPU configuration Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 590110 X20CPx58x: I/O Datapoints "SupplyVoltage" and "SupplyCurrent" for onboard PS module Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 590125 Module documentation revised Data sheet V1.39 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 603380 / Support ID: 400250890 POWERLINK CNs with configuration "Optimization: Minimal latency": No input data received POWERLINK CNs with configuration "Optimization: Minimal latency" and "Chained station: On" that are not physically present in the network can cause no input data to be received from all CNs with setting "Optimization: Minimal latency". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(136) Version 1.4.2.0: ID: 537770 / Support ID: 400204420 POWERLINK V2: no asynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(131) Version 1.4.0.0: ID: 497865 Configurable negative temperature display range Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters when replacing the CPU Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.0.0: ID: 462620 IP packets with multicast addresses not received by POWERLINK interface (problem onlyoccurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462640 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 462725 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462805 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.2.0.0: ID: 443655 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445140 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(15), 1\57883a0.epl(128) Version 1.1.0.0: ID: 417225 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417310 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417365 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 417495 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423920 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on thecontrolled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424035 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMTstatus in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(15), 1\57883a0.epl(127) Version 1.0.1.1: ID: 391690/ Support ID: 400137793 Correction terminal mode Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.1.0: ID: 388285 / Support ID: 0 Sporadic error when starting theonboard POWERLINK interface corrected Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.0.1: ID: 311570 Support X20cCP1584 Enhancement online-help Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(12), 1\57883a0.epl(123) Version 1.0.0.0: ID: 311570 Support X20cCP1584 First version Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(11), 1\57883a0.epl(121) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.8.0.0 | * | 12.12.2019 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20cCP1584 Version 1.8.0.0: ID: 652280 POWERLINK: Possible failure of already configured CNs if new "chained stations" added during operation Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 652445 Error correction: DNA tree topologies not always started up correctly Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(141) Version 1.6.0.0: ID: 635430 Module documentation revised Data sheet V1.52 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 635555 POWERLINK-Manager: With frequent failure of CN's, which are operated with the optimization "Chained station" it can be happen that failed CN's were not longer adressed by the manager. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(138) Version 1.5.0.0: ID: 542445 Changing the position of "Temperature datatype configuration" in the CPU configuration Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 590110 X20CPx58x: I/O Datapoints "SupplyVoltage" and "SupplyCurrent" for onboard PS module Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 590125 Module documentation revised Data sheet V1.39 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 603380 / Support ID: 400250890 POWERLINK CNs with configuration "Optimization: Minimal latency": No input data received POWERLINK CNs with configuration "Optimization: Minimal latency" and "Chained station:On" that are not physically present in the network can cause no input data tobe received from all CNs with setting "Optimization: Minimal latency". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(136) Version 1.4.2.0: ID: 537770 / Support ID: 400204420 POWERLINK V2: no asynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of atiming problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(131) Version 1.4.0.0: ID:497865 Configurable negative temperature display range Channel description changed: Yes Configuration description changed: Yes Firmwarechanged: No ID: 520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters when replacing the CPU Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.0.0: ID: 462620 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs withAutomation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID:462640 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 462725 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462805 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.2.0.0: ID: 443655 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445140 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(15), 1\57883a0.epl(128) Version 1.1.0.0: ID: 417225 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417310 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417365 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 417495 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423920 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424035 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(15), 1\57883a0.epl(127) Version 1.0.1.1: ID: 391690 / Support ID: 400137793 Correction terminal mode Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.1.0: ID: 388285 / Support ID: 0 Sporadic error when starting the onboard POWERLINK interface corrected Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.0.1: ID: 311570 Support X20cCP1584 Enhancement online-help Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(12), 1\57883a0.epl(123) Version 1.0.0.0: ID: 311570 Support X20cCP1584 First version Channel description changed: No Configuration description changed: No Firmwarechanged: No Firmware: 1\57883_0.pci(11), 1\57883a0.epl(121) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.6.0.0 | * | 16.04.2019 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20cCP1584 Version 1.6.0.0: ID: 635430 Module documentation revised Data sheet V1.52 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 635555 POWERLINK-Manager: With frequent failure of CN's, which are operated with the optimization "Chained station" it can be happen that failed CN's were not longer adressed by the manager. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(138) Version 1.5.0.0: ID: 542445 Changing the position of "Temperature data type configuration" in the CPU configuration Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 590110 X20CPx58x: I/O Datapoints "SupplyVoltage" and "SupplyCurrent" for onboard PS module Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 590125 Module documentation revised Data sheet V1.39 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 603380 / Support ID: 400250890 POWERLINK CNs with configuration "Optimization: Minimal latency": No input data received POWERLINK CNs with configuration "Optimization: Minimal latency" and "Chained station: On" that are not physically present in the network can cause no input data to be received from all CNs with setting "Optimization: Minimal latency". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(136) Version 1.4.2.0: ID: 537770 / Support ID: 400204420 POWERLINK V2: no asynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(131) Version 1.4.0.0: ID: 497865 Configurable negative temperaturedisplay range Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters when replacing the CPU Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.0.0: ID:462620 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462640 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 462725 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462805 /Support ID: 400164226 Corrected DRAM sizes in documentation Channeldescription changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.2.0.0: ID: 443655 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445140 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(15), 1\57883a0.epl(128) Version 1.1.0.0: ID: 417225 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417310 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417365 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 417495 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423920 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoCjitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424035 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(15), 1\57883a0.epl(127) Version 1.0.1.1: ID: 391690 / Support ID: 400137793 Correction terminal mode Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.1.0: ID: 388285 / Support ID: 0 Sporadic error when starting the onboard POWERLINK interface corrected Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.0.1: ID: 311570 Support X20cCP1584 Enhancement online-help Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(12), 1\57883a0.epl(123) Version 1.0.0.0: ID: 311570 Support X20cCP1584 First version Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(11),1\57883a0.epl(121) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.5.0.0 | * | 07.09.2018 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20cCP1584 Version 1.5.0.0: ID: 542445 Changing the position of "Temperature data type configuration" in the CPU configuration Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 590110 X20CPx58x: I/O Datapoints "SupplyVoltage" and "SupplyCurrent" for onboard PS module Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 590125 Module documentation revised Data sheet V1.39 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 603380 / Support ID: 400250890 POWERLINK CNs with configuration "Optimization: Minimal latency": No input data received POWERLINK CNs with configuration "Optimization: Minimal latency" and "Chained station: On" that are not physically present in the network can cause no input datato be received from all CNs with setting "Optimization: Minimal latency". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(136) Version 1.4.2.0: ID: 537770 / Support ID: 400204420 POWERLINK V2: no asynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frameswere sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(131) Version 1.4.0.0: ID: 497865 Configurable negative temperature display range Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters when replacing the CPU Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.3.0.0: ID: 462620 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462640 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 462725 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462805 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.2.0.0: ID: 443655 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445140 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(15), 1\57883a0.epl(128) Version 1.1.0.0: ID: 417225 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417310 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417365 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 417495 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423920 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424035 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(15), 1\57883a0.epl(127) Version 1.0.1.1: ID: 391690 / Support ID: 400137793 Correction terminal mode Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.1.0: ID: 388285 / Support ID: 0 Sporadic error when starting the onboard POWERLINK interface corrected Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.0.1: ID: 311570 Support X20cCP1584 Enhancement online-help Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(12), 1\57883a0.epl(123) Version 1.0.0.0: ID: 311570 Support X20cCP1584 First version Channeldescription changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(11), 1\57883a0.epl(121) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.4.2.0 | * | 29.05.2017 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20CP3586 Version 1.4.2.0: ID: 536520 / Support ID: 400204420 POWERLINK V2: noasynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(131) Version 1.4.1.0: ID: 536520 /Support ID: 400204420 POWERLINK V2: no asynchronous frames in mode NMT PRE_OPERATIONAL_1 Because of a timing problem in the firmware it could happen that no asynchronous frames were sent in the mode PRE_OPERATIONAL_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.4.0.0: ID: 497865 Configurable negative temperature display range Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 520790 Module documentation revised Data sheet V 1.37 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 521655 Correct setting of ETH-parameters when replacing the CPU Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.3.2.0: ID: 490210 Additional info data points FirmwareVersion and HardwareVariant Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.3.0.0: ID: 462610 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462710 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 462800 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 462875 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(17), 1\48939a0.epl(129) Version 1.2.0.0: ID: 443705 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445135 Documentation changed Channel description changed: No Configuration description changed: No Firmwarechanged: No Firmware: 1\48939_0.pci(15), 1\48939a0.epl(128) Version 1.1.1.0: ID: 434150 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(15), 1\48939a0.epl(127) Version 1.1.0.0: ID: 380887 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 386680 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413270 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, thedropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417160 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417235 Support of Poll Response Chaining on iCN Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417430 Optimized EMC characteristics for GL Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes ID: 423325 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(15), 1\48939a0.epl(127) Version 1.0.4.0: ID: 344995 / Support ID: - POWERLINK V1 MN mode: "Nettime SoC" is not increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 345645 POWERLINK V1 MN mode Error correction: Cyclic input data and net time toggle between the last two received values when CNs drop out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 359040 POWERLINK MN mode: If "Multiplexing prescale" >= 9, then the input data of the multiplexed stations that were configured in the last "network cycle" were not transferred in certainconfigurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 359285 / Support ID: 400113446 POWERLINK V2 MN mode: Asynchronous connection losses mayoccur as a result of high asynchronous loads on the POWERLINK network and high loads on the CPU. This could maintain you to an error 32205 Timeout whilewriting par. via acyclic channel. Channel description changed: No Configuration description changed: No Firmware changed: Yes Version1.0.3.0: ID: 338595 / Support ID: 400113132 Half-duplex Ethernet connections are not detected when using "Ethernet" operating mode with baud rate "100 MBit auto". This reduces total data throughput. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(123) Version 1.0.2.0: ID: 332415 / Support ID: 400092134 POWERLINK V1: If the "Activate Ethernet communication off" option is enabled, asynchronous POWERLINK communication fails in some circumstances. The following configuration may cause asynchronous communication to fail: - POWERLINK V1 - "Activate Ethernet communication off" - POWERLINK CNs on the network that also support POWERLINK V2 This upgrade can be installed to resolve this problem. It is also possible toset "Activate Ethernet communication" to "On". Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 336755 POWERLINK V2 MN mode: It was possible that an undefined state occurred during booting that causedtheinterface to fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 337480 / SupportID: 400108118 POWERLINK V2 CN mode It was possible that an undefined state occurred during booting that causedthe interface to fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(120) Version 1.0.1.4: ID: 307295 Enhancement English online-help and error corrections Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\48939_0.pci(11), 1\48939a0.epl(117) Version 1.0.1.3: ID: 285165 Support X20CP3586 First Version Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\48939_0.pci(11), 1\48939a0.epl(117) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.3.0.0 | * | 16.12.2015 | 2 MB | EXE | AS4_HW_X20CP3586.exe | |
| Popis |
V4.0 HW Upgrade (X20CP3586) Revision information X20cCP1584 Version 1.3.0.0: ID: 425270 / Support ID: 400151344 Corrections EPLAN macro Channel description changed: No Configuration description changed: No Firmware changed: No ID: 447705 / Support ID: 400164226 Corrected DRAM sizes in documentation Channel description changed: No Configuration description changed: No Firmware changed: No ID: 455310 / Support ID: 400134699 Reduced X2X susceptibility to disturbances Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 455320 Update online help Channel description changed: No Configuration description changed: No Firmware changed: No ID: 455345 IP packets with multicast addresses not received by POWERLINK interface (problem only occurs with Automation Runtime versions <A4.23) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(17), 1\57883a0.epl(129) Version 1.2.0.0: ID: 443655 / Support ID: 400154848 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 445140 Documentation changed Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(15), 1\57883a0.epl(128) Version 1.1.0.0: ID: 417225 Enhancement ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 417310 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 417365 Documentation: enhancements and corrections Channel description changed: No Configuration description changed: No Firmware changed: No ID: 417495 Optimized EMC characteristics for GL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 423920 / Support ID: 400138730 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424035 / Support ID: 400150240 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(15), 1\57883a0.epl(127) Version 1.0.1.1: ID: 391690 / Support ID: 400137793 Correction terminal mode Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.1.0: ID: 388285 / Support ID: 0 Sporadic error when starting the onboard POWERLINK interface corrected Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(13), 1\57883a0.epl(123) Version 1.0.0.1: ID: 311570 Support X20cCP1584 Enhancement online-help Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57883_0.pci(12), 1\57883a0.epl(123) Version 1.0.0.0: ID: 311570 Support X20cCP1584 First version Channeldescription changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57883_0.pci(11), 1\57883a0.epl(121) |
|||||
