DWL@DWL10000243752
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
---|---|---|---|---|---|---|
1.4.0.0 | * | 26.07.2021 | 734 KB | EXE | AS4_HW_5ACPCC.MPL0-00.exe | |
Popis |
V4.0 HW Upgrade (5ACPCC.MPL0-00) Revision information 5ACPCC.MPL0-00.MPL0-00 Version 1.4.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration descriptionchanged: yes Firmware changed: no Version 1.3.0.0: ID: 448530 POWERLINK V2: "Controlled node" mode After a POWERLINK managerfailed, the controlled node sometimes registered with an incorrect NMT statusin the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 448535 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 448545 Support of Poll Response Chaining on iCN Channel description changed:No Configuration description changed: No Firmware changed: Yes ID: 448550 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(32777), 1\43815a0.epl(128) Version 1.1.0.0: ID: 344245 POWERLINK V2 CN mode POWERLINK V1: If the "Activate Ethernet communication off"option is enabled, asynchronous POWERLINK communication fails in some circumstances. OutputDMAMargin datapoint shows a valid Value It was possible that an undefined state occurred during booting that causedthe interface to fail The following configuration may cause asynchronous communication to fail: - POWERLINK V1 - "Activate Ethernet communication off" - POWERLINK CNs on the network that also support POWERLINK V2 This upgrade can be installed to resolve this problem. It is also possible toset "Activate Ethernet communication" to "On". Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(30983), 1\43815a0.epl(121) Version 1.0.2.1: ID: 277783 Correction of the product description Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\43815_0.pci(28677), 1\43815a0.epl(112) Version 1.0.2.0: ID: 268975 New FPGA firmware V05 and new POWERLINK firmware V112 FPGA firmware: - ARWin - Update bugfix - no power fail nedded anymore POWERLINK firmwar: - POWERLINK: In controlled node mode, the I/O mapping was not applied when the manager was restarted. - POWERLINK: Thenet time is not always transferred correctly to the application. - POWERLINK V2 CN mode: Frequent MN failures result inCPU going into Service mode. - Warning 32168 "POWERLINK V2: Invalid frame format" on iCN with "Chaned Station" on the same network Error correction: When an iCN is used in thesame POWERLINK network with a"Chained Station", there may be warnings 32168 in the logger. The reason for this warning is that the sync response frames that are used to measure the timing of the"Chained Station" are not recognized by the iCN. - POWERLINK V2: If the the Ready-Flag was canceled on the network, the ModuleOK was not cleared. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(28677), 1\43815a0.epl(112) Version 1.0.1.1: ID: 253700 Add-on "Modul-OK" Add-on "Modul-OK" in I/O Mapping Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(27140), 1\43815a0.epl(106) Version 1.0.1.0: ID: 250445 Add-on "Modul-OK" Add-on "Modul-OK" in I/O Mapping Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(27140), 1\43815a0.epl(106) Version 1.0.0.0: ID: 207495 Initial version Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\43815_0.pci(27139), 1\43815a0.epl(106) |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.3.0.0 | * | 08.10.2015 | 750 KB | EXE | AS4_HW_5ACPCC.MPL0-00.exe | |
Popis |
V4.0 HW Upgrade (5ACPCC.MPL0-00) Revision information 5ACPCC.MPL0-00 Version 1.3.0.0: ID: 448530 POWERLINK V2: "Controlled node" mode After a POWERLINK manager failed, the controlled node sometimes registered with an incorrect NMT status in the ident response. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 448535 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 448545 Support of Poll Response Chaining on iCN Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 448550 IP packets with multicast addresses not received by the POWERLINK interface Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(32777), 1\43815a0.epl(128) Version 1.1.0.0: ID: 344245 POWERLINK V2 CN mode POWERLINK V1: If the "Activate Ethernet communication off" option is enabled, asynchronous POWERLINK communication fails in some circumstances. OutputDMAMargin datapoint showsa valid Value It was possible that an undefined state occurred during booting that causedthe interface to fail The following configuration maycause asynchronous communication to fail: - POWERLINK V1 - "Activate Ethernet communication off" - POWERLINK CNs on the network that also support POWERLINK V2 This upgrade can be installed to resolve this problem. It is also possible toset "Activate Ethernet communication" to "On". Channel description changed: No Configuration description changed: No Firmwarechanged: Yes Firmware: 1\43815_0.pci(30983), 1\43815a0.epl(121) Version 1.0.2.1: ID: 277783 Correction of the product description Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\43815_0.pci(28677), 1\43815a0.epl(112) Version 1.0.2.0: ID: 268975 New FPGA firmware V05 and new POWERLINK firmware V112 FPGA firmware: - ARWin - Update bugfix - no power fail nedded anymore POWERLINK firmwar: - POWERLINK: In controlled node mode, the I/O mapping was not applied when the manager was restarted. - POWERLINK: The net time is not always transferred correctly to the application. - POWERLINK V2 CN mode: Frequent MN failures result inCPU going into Service mode. - Warning 32168 "POWERLINK V2: Invalidframe format" on iCN with "Chaned Station" on the same network Error correction: When an iCN is used in the same POWERLINK network with a "Chained Station", there may be warnings 32168 in the logger. The reason for thiswarning is that the sync response frames that are usedto measure the timing of the"Chained Station" are not recognized by the iCN. - POWERLINK V2: Ifthe the Ready-Flag was canceled on the network, the ModuleOK was not cleared. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(28677), 1\43815a0.epl(112) Version 1.0.1.1: ID: 253700 Add-on "Modul-OK" Add-on "Modul-OK" in I/O Mapping Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\43815_0.pci(27140), 1\43815a0.epl(106) Version 1.0.1.0: ID:250445 Add-on "Modul-OK" Add-on "Modul-OK" in I/O Mapping Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\43815_0.pci(27140), 1\43815a0.epl(106) Version 1.0.0.0: ID: 207495 Initial version Channel description changed: No Configuration description changed: No Firmwarechanged: No Firmware: 1\43815_0.pci(27139), 1\43815a0.epl(106) |