DWL@DWL10000390404

Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
2.11.0.0 * 31.01.2020 2 MB EXE AS3.0_HW_X20BC8083.exe
Popis V3.0 HW Upgrade (X20BC8083)

Revision information X20BC8083

Version 2.11.0.0:

ID: 664345
DNA: Hub of PLK BC active until first IDENT_REQUEST
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 664365
Adaptationsfor Automation Studio 4.8
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 665745
ModuleOk of IO module FALSE after warm restart even though the module is working as expected
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 665825
Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 666190
Module documentation revised
Data sheet V2.38
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(430), 1\9843_3.fw(430), 1\9843_4.fw(430), 1\9843_5.fw(430), 1\9843_6.fw(430), 1\9843_7.fw(430)

Version 2.10.0.0:

ID: 647930
Optimization of the firmware update process
Channel description changed: No
Configuration description changed: No
Firmwarechanged: Yes
Firmware: 1\9843_2.fw(428), 1\9843_3.fw(428), 1\9843_4.fw(428), 1\9843_5.fw(428), 1\9843_6.fw(428), 1\9843_7.fw(428)

Version 2.9.0.0:

ID: 624090
Optimization of hub behavior
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629005
Ring redundancy: Cannot address the CN that closes the ring
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629070
DNA: BC as head-end station switching hub off again
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629155
Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(427), 1\9843_3.fw(427), 1\9843_4.fw(427), 1\9843_5.fw(427), 1\9843_6.fw(427)

Version 2.8.0.0:

ID: 619135 / Support ID: 400257683
DNA: PLK hub forwarding for the next node not enabled in rare cases
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 619175 / Support ID: 400262159
Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active
Channel description changed: No
Configuration descriptionchanged: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(426), 1\9843_3.fw(426), 1\9843_4.fw(426), 1\9843_5.fw(426), 1\9843_6.fw(426)

Version 2.7.0.0:

ID: 586730 / Support ID: 400241376
Temporary toggling of data point ModuleOk if I/O module fails
Channel description changed:No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(424), 1\9843_3.fw(424), 1\9843_4.fw(424), 1\9843_5.fw(424), 1\9843_6.fw(424)

Version 2.6.0.0:

ID: 574215
Optimization of boot procedure for hardware variant 5 und 6
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(423), 1\9843_3.fw(423), 1\9843_4.fw(423), 1\9843_5.fw(423), 1\9843_6.fw(423)

Version 2.5.6.0:

ID: 564800
Optimization the boot up for hardware variant 5
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(422), 1\9843_3.fw(422), 1\9843_4.fw(422), 1\9843_5.fw(422)

Version 2.5.5.0:

ID: 551115
Startup time optimizations
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(421), 1\9843_3.fw(421), 1\9843_4.fw(421), 1\9843_5.fw(421)

Version 2.5.4.0:

ID: 540310 / Support ID: 400202320
BC sporadically not going into Operational due to X2X-bus problems at startup
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(419), 1\9843_3.fw(419), 1\9843_4.fw(419)

Version 2.5.3.0:

ID: 523465 / Support ID: 400205694
safety modules not switching to operational state
SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together.
Channel descriptionchanged: No
Configuration description changed: No
Firmware changed:Yes
Firmware: 1\9843_2.fw(417), 1\9843_3.fw(417), 1\9843_4.fw(417)

Version 2.5.2.0:

ID: 493880 / Support ID: 400103115, 400101850, 400154063, 400190752
First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(415), 1\9843_3.fw(415), 1\9843_4.fw(415)

Version 2.5.0.0:

ID: 468040/ Support ID: 400178654
Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468045 / Support ID: 400177243
X2X FW update of several X2X modules is not working
Channel description changed: No
Configurationdescription changed: No
Firmware changed: Yes

ID: 468050
optimization of X2X FW updates
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468525
CiR support
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(413), 1\9843_3.fw(413), 1\9843_4.fw(413)

Version 2.3.0.0:

ID: 460100 / Support ID: 400168329
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 460220 / Support ID: 400150525
Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 462080
Module documentation revised
Data sheet V 2.32
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(411), 1\9843_3.fw(411), 1\9843_4.fw(411)

Version 2.2.1.0:

ID: 445325 / Support ID: 400162116
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 448525 / Support ID: 400164639
When combining X20BC8083 with Version 2.2.0.0 and X20HB2881 no PLK connection is available
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(401), 1\9843_3.fw(401), 1\9843_4.fw(401)

Version 2.2.0.0:

ID: 439095 / Support ID: 400150496
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 439200 / Support ID: 400128436
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(400), 1\9843_3.fw(400),1\9843_4.fw(400)

Version 2.1.0.0:

ID: 404500
X2XLink-BC:StationAtBusEnd does not change, when empty backplanes are addedor removed.
When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change.
The data pointdie change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is suppliedwith power, but the supply for the IO is missing.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 2.0.0.0:

ID: 390270 / Support ID: 400129274
Uncommon X2Xsettings cause permanent boot of bus controller
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 1.3.5.0:

ID: 310785 / Support ID: 400097674
POWERLINK V1: Bug-fix for Up/Downgrade
POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 311015 / Support ID: 400051206
Expansion: Link- selector flag
New datapoints:&lt;br/&gt;- RedundancyFirstLinkState&lt;br/&gt;- RedundancySecondLinkState
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(168), 1\9843_3.fw(168), 1\9843_4.fw(168)

Version 1.3.4.0:

ID: 305150 / Support ID: 400094368
ACOPOSmulti with SafeMC, asynchronous communication lost
When there was a high load on the CPU, asynchronouscommunication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(167), 1\9843_3.fw(167), 1\9843_4.fw(167)

Version 1.3.3.0:

ID: 298985 / Support ID: 400090781
Problem with FW-Update of IO modules on Powerlinkbuscontrollers
The firmware update of IO modules does not work in certain configurations.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(165), 1\9843_3.fw(165), 1\9843_4.fw(165)

Version 1.3.2.0:

ID: 160985
Additional diagnostic data points
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 291890 / Support ID: 400087996
Error when running X20BC8083 (Rev. <G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(164), 1\9843_3.fw(164), 1\9843_4.fw(164)

Version 1.3.1.0:

ID: 289015
Certain X2X configurationsdon't work
In very rare I/O constellations, the X2X modules don't start
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 290080
New Hardwarevariant 4
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(163), 1\9843_3.fw(163), 1\9843_4.fw(163)

Version 1.3.0.0:

ID: 277175
Support of 'Multiple Asynchronous Send'
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 277745
New X2X datapoints
- NettimeOffsetX2X and NettimeX2X
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(160), 1\9843_3.fw(160)

Version 1.2.0.0:

ID: 246550
DNA support; Update behavior on X2X bus ofthe BC improved
- DNA support (Dynamic Node Allocation)
- faster updating of modules with big FW files on the X2X bus of the BC
- new objects: 20A3h and 2000h/9
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(152), 1\9843_3.fw(152)

Version 1.0.9.0:

ID: 220630
Extensions and Bugfixes
- Combination of PollResponse-Chaining and PollRequest-Synchronization did not work correctly (A&P 218765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(146)

Version 1.0.8.0:

ID: 218500
Extensions and Bugfixes
- Firmware-Version is transferred via IdentResponse in the first 4 bytes ofthe field VendorSpecificExt1
- Support of PollResponse-Chaining
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(145)

Version 1.0.7.0:

ID: 214455
Extensions and Bugfixes
- In systems with high X2X load it happened that IO modules were not restarted when the CPU did a warmstart (A&P 211805)
- Activation of MultipleRead/Write feature for faster startup after configuration change
- Writing to Objekt 20F0h/SubIndex 22 caused SDO errors when accessed faster than allowed
- Number of configuration entries per IO module changed from 100 to 155
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(144)

Version 1.0.6.0:

ID: 210960
Extensions and Bugfixes
- Error correction for operation in Powerlink V1 networks (A&P 210765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(143)

Version 1.0.4.0:

ID: 183385
New info-/diagnostic data points, new FW 1.39 for signal filter and corrections
New info-/diagnostic data points in HWC, new FW 1.39 for signal filter and corrections
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(141)

Version 1.0.3.0:

ID: 173305
Extensions and Bugfixes
- Improvement of X2X Timings (Jitter reduced from 180ns to 20ns) (A&P167857 und 171987)
- Optimizations for operation in 200us networks
- 2 nodes with the same node number generated disturbance on the network (A&P 166040)
- Functions for a new firmware download mechanism implemented (A&P 168537)
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(138)

Version 1.0.2.0:

ID: 164665
Extensions
- Extensions for operation with Safety
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(136)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
2.10.0.0 * 10.07.2019 2 MB EXE AS3.0_HW_X20BC8083.exe
Popis V3.0 HW Upgrade (X20BC8083)

Revision information X20BC8083

Version 2.10.0.0:

ID: 647930
Optimization of the firmware update process
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(428), 1\9843_3.fw(428), 1\9843_4.fw(428), 1\9843_5.fw(428), 1\9843_6.fw(428), 1\9843_7.fw(428)

Version 2.9.0.0:

ID: 624090
Optimization of hub behavior
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629005
Ring redundancy: Cannot address the CN that closes the ring
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629070
DNA: BC as head-end station switching hub off again
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629155
Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(427), 1\9843_3.fw(427), 1\9843_4.fw(427), 1\9843_5.fw(427), 1\9843_6.fw(427)

Version 2.8.0.0:

ID: 619135 / Support ID: 400257683
DNA: PLK hub forwarding for the next node not enabled in rare cases
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 619175 / Support ID: 400262159
Outputs of I/O modules behind the bus coupler not working in some cases ifpoll-response chaining active
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(426), 1\9843_3.fw(426), 1\9843_4.fw(426), 1\9843_5.fw(426), 1\9843_6.fw(426)

Version 2.7.0.0:

ID: 586730 / Support ID: 400241376
Temporary toggling of data point ModuleOk if I/O module fails
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(424), 1\9843_3.fw(424), 1\9843_4.fw(424), 1\9843_5.fw(424), 1\9843_6.fw(424)

Version 2.6.0.0:

ID:574215
Optimization of boot procedure for hardware variant 5 und 6
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(423), 1\9843_3.fw(423), 1\9843_4.fw(423), 1\9843_5.fw(423), 1\9843_6.fw(423)

Version 2.5.6.0:

ID: 564800
Optimization the boot up for hardware variant 5
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(422), 1\9843_3.fw(422), 1\9843_4.fw(422), 1\9843_5.fw(422)

Version 2.5.5.0:

ID: 551115
Startup time optimizations
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(421), 1\9843_3.fw(421), 1\9843_4.fw(421), 1\9843_5.fw(421)

Version 2.5.4.0:

ID: 540310 / Support ID: 400202320
BC sporadically not going into Operational due to X2X-bus problems at startup
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(419), 1\9843_3.fw(419), 1\9843_4.fw(419)

Version 2.5.3.0:

ID: 523465 / Support ID: 400205694
safetymodules not switching to operational state
SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(417), 1\9843_3.fw(417), 1\9843_4.fw(417)

Version 2.5.2.0:

ID: 493880 / Support ID: 400103115, 400101850, 400154063, 400190752
First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(415), 1\9843_3.fw(415), 1\9843_4.fw(415)

Version 2.5.0.0:

ID: 468040 / Support ID: 400178654
Safety modules in connectionwith PLK BCs, with only input datapoints, are not initialized.by SL
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468045 / Support ID: 400177243
X2X FW update of several X2X modules is not working
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468050
optimization of X2X FW updates
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468525
CiR support
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(413), 1\9843_3.fw(413), 1\9843_4.fw(413)

Version 2.3.0.0:

ID: 460100 / Support ID: 400168329
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 460220 / Support ID: 400150525
Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 462080
Moduledocumentation revised
Data sheet V 2.32
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(411), 1\9843_3.fw(411), 1\9843_4.fw(411)

Version2.2.1.0:

ID: 445325 / Support ID: 400162116
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 448525 / Support ID: 400164639
When combining X20BC8083 with Version 2.2.0.0 and X20HB2881 no PLK connectionis available
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(401), 1\9843_3.fw(401), 1\9843_4.fw(401)

Version 2.2.0.0:

ID: 439095 / Support ID: 400150496
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 439200 / Support ID: 400128436
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(400), 1\9843_3.fw(400), 1\9843_4.fw(400)

Version 2.1.0.0:

ID: 404500
X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed.
When empty backplanes are plugged or unplugged on theend of the X2XLink thediagnostic data point "StationAtBusEnd" die not change.
The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the"StationAtBusEnd" faster. The same problem also occurs with modules where theX2XLink is supplied with power, but the supply for the IO is missing.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 2.0.0.0:

ID: 390270 / Support ID: 400129274
Uncommon X2X settings cause permanent boot of bus controller
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 1.3.5.0:

ID: 310785 / Support ID: 400097674
POWERLINK V1: Bug-fix for Up/Downgrade
POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 311015 / Support ID: 400051206
Expansion: Link- selector flag
New datapoints:&lt;br/&gt;- RedundancyFirstLinkState&lt;br/&gt;- RedundancySecondLinkState
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(168), 1\9843_3.fw(168), 1\9843_4.fw(168)

Version 1.3.4.0:

ID: 305150 / Support ID: 400094368
ACOPOSmulti with SafeMC, asynchronous communication lost
When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware:1\9843_2.fw(167), 1\9843_3.fw(167), 1\9843_4.fw(167)

Version 1.3.3.0:

ID: 298985 / Support ID: 400090781
Problem with FW-Update of IO modules on Powerlink buscontrollers
The firmware update of IO modules does not work in certain configurations.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(165), 1\9843_3.fw(165), 1\9843_4.fw(165)

Version 1.3.2.0:

ID: 160985
Additional diagnostic data points
Channel description changed: Yes
Configuration description changed: No
Firmwarechanged: No

ID: 291890 / Support ID: 400087996
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(164), 1\9843_3.fw(164), 1\9843_4.fw(164)

Version 1.3.1.0:

ID: 289015
Certain X2X configurations don't work
In very rare I/O constellations, the X2X modules don't start
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 290080
New Hardwarevariant 4
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(163), 1\9843_3.fw(163), 1\9843_4.fw(163)

Version 1.3.0.0:

ID: 277175
Support of 'Multiple Asynchronous Send'
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 277745
New X2X datapoints
- NettimeOffsetX2X and NettimeX2X
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(160), 1\9843_3.fw(160)

Version 1.2.0.0:

ID: 246550
DNA support; Update behavior on X2X bus of the BC improved
- DNA support (Dynamic Node Allocation)
- faster updating of modules with big FW files on the X2X bus of the BC
- new objects: 20A3h and 2000h/9
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(152), 1\9843_3.fw(152)

Version 1.0.9.0:

ID: 220630
Extensions and Bugfixes
- Combination of PollResponse-Chaining and PollRequest-Synchronization did not work correctly (A&P 218765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(146)

Version 1.0.8.0:

ID: 218500
Extensions and Bugfixes
- Firmware-Version is transferred via IdentResponse in the first 4 bytes ofthe field VendorSpecificExt1
- Support of PollResponse-Chaining
Channel description changed:No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(145)

Version 1.0.7.0:

ID: 214455
Extensions and Bugfixes
- In systems with high X2X load it happened that IO modules were not restarted when the CPU did a warmstart (A&P 211805)
-Activation of MultipleRead/Write feature for faster startup after configuration change
- Writing to Objekt 20F0h/SubIndex 22 caused SDO errors when accessed faster than allowed
- Number of configuration entries per IO module changed from 100 to 155
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(144)

Version 1.0.6.0:

ID: 210960
Extensions and Bugfixes
- Error correction for operation in Powerlink V1 networks (A&P 210765)
Channel description changed: No
Configuration description changed:No
Firmware changed: Yes
Firmware: 1\9843_1.fw(143)

Version 1.0.4.0:

ID: 183385
New info-/diagnostic data points, new FW 1.39 for signal filter and corrections
New info-/diagnostic data points in HWC, new FW 1.39 for signal filter and corrections
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(141)

Version 1.0.3.0:

ID: 173305
Extensions and Bugfixes
- Improvement of X2X Timings (Jitter reduced from 180ns to 20ns) (A&P167857 und 171987)
- Optimizations for operation in 200us networks
- 2 nodes with the same node number generated disturbance on the network (A&P 166040)
- Functions for a new firmware download mechanism implemented (A&P 168537)
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(138)

Version 1.0.2.0:

ID: 164665
Extensions
- Extensions for operation with Safety
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(136)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
2.9.0.0 * 01.03.2019 2 MB EXE AS3.0_HW_X20BC8083.exe
Popis V3.0 HW Upgrade (X20BC8083)

Revision information X20BC8083

Version 2.9.0.0:

ID: 624090
Optimization of hub behavior
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629005
Ring redundancy: Cannot address theCN that closes the ring
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629070
DNA: BC as head-end station switching hub off again
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 629155
Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(427), 1\9843_3.fw(427), 1\9843_4.fw(427), 1\9843_5.fw(427), 1\9843_6.fw(427)

Version 2.8.0.0:

ID: 619135 / Support ID: 400257683
DNA: PLK hub forwarding for the next node not enabled in rare cases
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 619175 / Support ID: 400262159
Outputsof I/O modules behind the bus coupler not working in some cases if poll-response chaining active
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(426), 1\9843_3.fw(426), 1\9843_4.fw(426), 1\9843_5.fw(426), 1\9843_6.fw(426)

Version 2.7.0.0:

ID: 586730 / Support ID: 400241376
Temporary toggling of data point ModuleOk if I/O module fails
Channel descriptionchanged: No
Configuration description changed: No
Firmware changed:Yes
Firmware: 1\9843_2.fw(424), 1\9843_3.fw(424), 1\9843_4.fw(424), 1\9843_5.fw(424), 1\9843_6.fw(424)

Version 2.6.0.0:

ID: 574215
Optimization of boot procedure for hardware variant 5 und 6
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(423), 1\9843_3.fw(423), 1\9843_4.fw(423), 1\9843_5.fw(423), 1\9843_6.fw(423)

Version 2.5.6.0:

ID: 564800
Optimization the boot up for hardware variant 5
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(422), 1\9843_3.fw(422), 1\9843_4.fw(422), 1\9843_5.fw(422)

Version 2.5.5.0:

ID: 551115
Startup timeoptimizations
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(421), 1\9843_3.fw(421), 1\9843_4.fw(421), 1\9843_5.fw(421)

Version 2.5.4.0:

ID: 540310 / Support ID: 400202320
BC sporadically not going into Operational due to X2X-bus problems at startup
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(419), 1\9843_3.fw(419), 1\9843_4.fw(419)

Version 2.5.3.0:

ID: 523465 / Support ID: 400205694
safety modules not switching to operational state
SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together.
Channel description changed: No
Configuration description changed: No
Firmwarechanged: Yes
Firmware: 1\9843_2.fw(417), 1\9843_3.fw(417), 1\9843_4.fw(417)

Version 2.5.2.0:

ID: 493880 / Support ID: 400103115, 400101850, 400154063, 400190752
First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(415), 1\9843_3.fw(415), 1\9843_4.fw(415)

Version 2.5.0.0:

ID: 468040 / Support ID: 400178654
Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468045 / Support ID: 400177243
X2X FW update of several X2X modules is not working
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468050
optimization of X2X FW updates
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468525
CiR support
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(413), 1\9843_3.fw(413), 1\9843_4.fw(413)

Version 2.3.0.0:

ID: 460100 / Support ID: 400168329
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 460220 / Support ID: 400150525
Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 462080
Module documentation revised
Data sheet V 2.32
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(411), 1\9843_3.fw(411), 1\9843_4.fw(411)

Version 2.2.1.0:

ID: 445325 / Support ID: 400162116
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 448525 / Support ID: 400164639
When combining X20BC8083 with Version 2.2.0.0 and X20HB2881 no PLK connection is available
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(401), 1\9843_3.fw(401), 1\9843_4.fw(401)

Version 2.2.0.0:

ID: 439095 / Support ID:400150496
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 439200 / Support ID: 400128436
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-oncycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(400), 1\9843_3.fw(400), 1\9843_4.fw(400)

Version 2.1.0.0:

ID: 404500
X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed.
When empty backplanes are plugged or unplugged on the end of theX2XLink thediagnostic data point "StationAtBusEnd" die not change.
The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink issupplied with power, but the supply for the IO is missing.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 2.0.0.0:

ID: 390270 / Support ID: 400129274
Uncommon X2X settings cause permanent boot of bus controller
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 1.3.5.0:

ID: 310785 / Support ID: 400097674
POWERLINK V1: Bug-fix for Up/Downgrade
POWERLINK V1 FW upgrade problem could beaccored after PowerOn beginning with HW- Upgrade Version 1.3.1.0
Channeldescription changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 311015 / Support ID: 400051206
Expansion: Link- selector flag
New datapoints:&lt;br/&gt;- RedundancyFirstLinkState&lt;br/&gt;- RedundancySecondLinkState
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(168), 1\9843_3.fw(168), 1\9843_4.fw(168)

Version 1.3.4.0:

ID: 305150 / Support ID: 400094368
ACOPOSmulti with SafeMC, asynchronous communication lost
When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication causedthe safety-IO to stop.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(167), 1\9843_3.fw(167), 1\9843_4.fw(167)

Version 1.3.3.0:

ID: 298985 / Support ID: 400090781
Problem with FW-Update of IO modules on Powerlink buscontrollers
The firmware update of IO modules does not work in certain configurations.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(165), 1\9843_3.fw(165), 1\9843_4.fw(165)

Version 1.3.2.0:

ID: 160985
Additional diagnostic data points
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 291890 / Support ID: 400087996
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(164), 1\9843_3.fw(164), 1\9843_4.fw(164)

Version 1.3.1.0:

ID: 289015
Certain X2X configurations don't work
In very rare I/O constellations, the X2X modules don't start
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 290080
New Hardwarevariant 4
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(163), 1\9843_3.fw(163), 1\9843_4.fw(163)

Version 1.3.0.0:

ID: 277175
Support of 'Multiple Asynchronous Send'
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID:277745
New X2X datapoints
- NettimeOffsetX2X and NettimeX2X
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(160), 1\9843_3.fw(160)

Version 1.2.0.0:

ID: 246550
DNA support; Update behavior on X2X bus of the BC improved
- DNA support (Dynamic Node Allocation)
- faster updating of modules with big FW files on the X2X bus of the BC
- new objects: 20A3h and 2000h/9
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(152), 1\9843_3.fw(152)

Version 1.0.9.0:

ID: 220630
Extensions and Bugfixes
- Combination of PollResponse-Chaining and PollRequest-Synchronization did not work correctly (A&P 218765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(146)

Version 1.0.8.0:

ID: 218500
Extensions and Bugfixes
- Firmware-Version is transferredvia IdentResponse in the first 4 bytes of the field VendorSpecificExt1
-Support of PollResponse-Chaining
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(145)

Version 1.0.7.0:

ID: 214455
Extensions and Bugfixes
- In systems with high X2X load it happened that IO modules were not restarted when the CPU did a warmstart (A&P 211805)
- Activationof MultipleRead/Write feature for faster startup after configuration change
- Writing to Objekt 20F0h/SubIndex 22 caused SDO errors when accessed faster than allowed
- Number of configuration entries per IO module changed from 100 to 155
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(144)

Version 1.0.6.0:

ID: 210960
Extensions and Bugfixes
- Error correction for operation in Powerlink V1 networks (A&P 210765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(143)

Version 1.0.4.0:

ID: 183385
New info-/diagnostic data points, new FW 1.39 for signal filter and corrections
New info-/diagnostic data points in HWC, new FW 1.39 for signal filter and corrections
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(141)

Version 1.0.3.0:

ID: 173305
Extensions and Bugfixes
- Improvement of X2X Timings (Jitter reduced from 180ns to 20ns) (A&P167857 und 171987)
- Optimizations for operation in 200us networks
- 2 nodes with the same node number generated disturbance on the network (A&P 166040)
- Functions for a new firmware download mechanism implemented (A&P 168537)
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(138)

Version 1.0.2.0:

ID: 164665
Extensions
- Extensions for operation with Safety
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(136)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
2.8.0.0 * 05.12.2018 2 MB EXE AS3.0_HW_X20BC8083.exe
Popis V3.0 HW Upgrade (X20BC8083)

Revision information X20BC8083

Version 2.8.0.0:

ID: 619135 / Support ID: 400257683
DNA: PLK hub forwarding for the next node not enabled in rare cases
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 619175 / Support ID: 400262159
Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(426), 1\9843_3.fw(426), 1\9843_4.fw(426), 1\9843_5.fw(426), 1\9843_6.fw(426)

Version 2.7.0.0:

ID: 586730 / Support ID: 400241376
Temporary toggling of data point ModuleOk if I/O module fails
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware:1\9843_2.fw(424), 1\9843_3.fw(424), 1\9843_4.fw(424), 1\9843_5.fw(424), 1\9843_6.fw(424)

Version 2.6.0.0:

ID: 574215
Optimization of boot procedure for hardware variant 5 und 6
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(423), 1\9843_3.fw(423), 1\9843_4.fw(423), 1\9843_5.fw(423), 1\9843_6.fw(423)

Version 2.5.6.0:

ID: 564800
Optimization the boot up for hardware variant 5
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(422), 1\9843_3.fw(422), 1\9843_4.fw(422), 1\9843_5.fw(422)

Version 2.5.5.0:

ID: 551115
Startup time optimizations
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(421), 1\9843_3.fw(421), 1\9843_4.fw(421), 1\9843_5.fw(421)

Version 2.5.4.0:

ID: 540310 /Support ID: 400202320
BC sporadically not going into Operational due to X2X-bus problems at startup
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(419), 1\9843_3.fw(419), 1\9843_4.fw(419)

Version 2.5.3.0:

ID: 523465 / Support ID: 400205694
safety modules not switching to operational state
SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(417), 1\9843_3.fw(417), 1\9843_4.fw(417)

Version 2.5.2.0:

ID: 493880 / Support ID: 400103115, 400101850, 400154063, 400190752
First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(415), 1\9843_3.fw(415), 1\9843_4.fw(415)

Version 2.5.0.0:

ID: 468040 / SupportID: 400178654
Safety modules in connection with PLK BCs, with only inputdatapoints, are not initialized.by SL
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468045 / Support ID: 400177243
X2X FW update of several X2X modules isnot working
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468050
optimization of X2X FW updates
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468525
CiR support
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(413), 1\9843_3.fw(413), 1\9843_4.fw(413)

Version 2.3.0.0:

ID: 460100 / Support ID: 400168329
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 460220 / Support ID: 400150525
Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC
Channeldescription changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 462080
Module documentation revised
Data sheet V 2.32
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(411), 1\9843_3.fw(411), 1\9843_4.fw(411)

Version 2.2.1.0:

ID: 445325 / Support ID: 400162116
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 448525 / Support ID: 400164639
When combining X20BC8083 withVersion 2.2.0.0 and X20HB2881 no PLK connection is available
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(401), 1\9843_3.fw(401), 1\9843_4.fw(401)

Version 2.2.0.0:

ID: 439095 / Support ID: 400150496
I/Omodules behind POWERLINK bus controllers no longer achieving Operationalmodeafter multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 439200 / Support ID: 400128436
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(400), 1\9843_3.fw(400), 1\9843_4.fw(400)

Version 2.1.0.0:

ID: 404500
X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed.
When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change.
The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. Thesame problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 2.0.0.0:

ID: 390270 / Support ID: 400129274
Uncommon X2X settings cause permanent boot of bus controller
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 1.3.5.0:

ID: 310785 / Support ID: 400097674
POWERLINK V1: Bug-fix forUp/Downgrade
POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 311015 / Support ID: 400051206
Expansion: Link- selector flag
New datapoints:&lt;br/&gt;- RedundancyFirstLinkState&lt;br/&gt;- RedundancySecondLinkState
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(168), 1\9843_3.fw(168), 1\9843_4.fw(168)

Version 1.3.4.0:

ID: 305150 / Support ID: 400094368
ACOPOSmulti with SafeMC, asynchronous communication lost
When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(167), 1\9843_3.fw(167), 1\9843_4.fw(167)

Version 1.3.3.0:

ID: 298985 / Support ID: 400090781
Problem with FW-Update of IO modules on Powerlink buscontrollers
The firmware update of IO modules does not work in certain configurations.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(165), 1\9843_3.fw(165), 1\9843_4.fw(165)

Version 1.3.2.0:

ID: 160985
Additional diagnostic data points
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 291890 / Support ID: 400087996
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(164), 1\9843_3.fw(164), 1\9843_4.fw(164)

Version 1.3.1.0:

ID: 289015
Certain X2X configurations don't work
In very rare I/O constellations, the X2X modules don't start
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 290080
New Hardwarevariant 4
Channeldescription changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(163), 1\9843_3.fw(163), 1\9843_4.fw(163)

Version 1.3.0.0:

ID: 277175
Support of 'Multiple Asynchronous Send'
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 277745
New X2X datapoints
- NettimeOffsetX2X and NettimeX2X
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed:Yes
Firmware: 1\9843_2.fw(160), 1\9843_3.fw(160)

Version 1.2.0.0:

ID: 246550
DNA support; Update behavior on X2X bus of the BC improved
- DNA support (Dynamic Node Allocation)
- faster updating of modules with big FW files on the X2X bus of the BC
- new objects: 20A3h and 2000h/9
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(152), 1\9843_3.fw(152)

Version 1.0.9.0:

ID: 220630
Extensions and Bugfixes
- Combination of PollResponse-Chaining and PollRequest-Synchronization did not work correctly (A&P 218765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(146)

Version 1.0.8.0:

ID: 218500
Extensions and Bugfixes
- Firmware-Version is transferred via IdentResponse in the first 4 bytes ofthe field VendorSpecificExt1
- Support of PollResponse-Chaining
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(145)

Version 1.0.7.0:

ID: 214455
Extensions and Bugfixes
- In systems with high X2X load it happened that IO modules were not restarted when the CPU did a warmstart (A&P 211805)
- Activation of MultipleRead/Write feature for faster startup after configuration change
- Writing to Objekt 20F0h/SubIndex 22 caused SDO errors when accessed faster than allowed
- Number of configuration entries per IO module changed from 100 to 155
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(144)

Version 1.0.6.0:

ID: 210960
Extensions and Bugfixes
- Error correction for operation in Powerlink V1 networks (A&P 210765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(143)

Version 1.0.4.0:

ID: 183385
New info-/diagnostic data points, new FW 1.39 for signal filter and corrections
New info-/diagnostic data points in HWC, new FW 1.39 for signal filter and corrections
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(141)

Version 1.0.3.0:

ID: 173305
Extensions and Bugfixes
- Improvement of X2X Timings (Jitter reduced from 180ns to 20ns) (A&P167857und 171987)
- Optimizations for operation in 200us networks
- 2 nodes with the same node number generated disturbance on the network (A&P 166040)
- Functions for a new firmware download mechanism implemented (A&P 168537)
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(138)

Version 1.0.2.0:

ID: 164665
Extensions
- Extensions for operation with Safety
Channel description changed: No
Configuration descriptionchanged: No
Firmware changed: No
Firmware: 1\9843_1.fw(136)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
2.7.0.0 * 17.04.2018 2 MB EXE AS3.0_HW_X20BC8083.exe
Popis V3.0 HW Upgrade (X20BC8083)

Revision information X20BC8083

Version 2.7.0.0:

ID: 586730 / Support ID: 400241376
Temporary toggling of data point ModuleOk if I/O module fails
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(424), 1\9843_3.fw(424), 1\9843_4.fw(424), 1\9843_5.fw(424), 1\9843_6.fw(424)

Version 2.6.0.0:

ID: 574215
Optimization of boot procedure for hardware variant 5 und 6
Channel descriptionchanged: No
Configuration description changed: No
Firmware changed:Yes
Firmware: 1\9843_2.fw(423), 1\9843_3.fw(423), 1\9843_4.fw(423), 1\9843_5.fw(423), 1\9843_6.fw(423)

Version 2.5.6.0:

ID: 564800
Optimization the boot up for hardware variant 5
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(422), 1\9843_3.fw(422), 1\9843_4.fw(422), 1\9843_5.fw(422)

Version 2.5.5.0:

ID: 551115
Startup time optimizations
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(421), 1\9843_3.fw(421), 1\9843_4.fw(421), 1\9843_5.fw(421)

Version 2.5.4.0:

ID: 540310 / Support ID: 400202320
BC sporadically not going into Operational due to X2X-bus problems at startup
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(419), 1\9843_3.fw(419), 1\9843_4.fw(419)

Version 2.5.3.0:

ID: 523465 / Support ID: 400205694
safety modules not switching to operational state
SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(417), 1\9843_3.fw(417), 1\9843_4.fw(417)

Version 2.5.2.0:

ID: 493880 / Support ID: 400103115, 400101850, 400154063, 400190752
First POWERLINK UDP ASnd SDO transfert after long timetakes up to 5s.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(415),1\9843_3.fw(415), 1\9843_4.fw(415)

Version 2.5.0.0:

ID: 468040 / Support ID: 400178654
Safety modules in connection with PLK BCs, withonly input datapoints, are not initialized.by SL
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468045 / Support ID: 400177243
X2X FW update of several X2Xmodules is not working
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468050
optimization of X2X FW updates
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468525
CiR support
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(413), 1\9843_3.fw(413), 1\9843_4.fw(413)

Version 2.3.0.0:

ID: 460100 / Support ID: 400168329
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 460220 / Support ID: 400150525
Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 462080
Module documentation revised
Data sheet V 2.32
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(411), 1\9843_3.fw(411), 1\9843_4.fw(411)

Version 2.2.1.0:

ID: 445325 / Support ID: 400162116
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 448525 / Support ID: 400164639
When combining X20BC8083 with Version 2.2.0.0 and X20HB2881 no PLK connection is available
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(401), 1\9843_3.fw(401), 1\9843_4.fw(401)

Version 2.2.0.0:

ID: 439095 / Support ID: 400150496
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 439200 / Support ID: 400128436
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(400), 1\9843_3.fw(400), 1\9843_4.fw(400)

Version 2.1.0.0:

ID: 404500
X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed.
When empty backplanes are plugged or unplugged on the end of the X2XLinkthediagnostic data point "StationAtBusEnd" die not change.
The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 2.0.0.0:

ID: 390270 / Support ID: 400129274
Uncommon X2X settings cause permanent boot of bus controller
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 1.3.5.0:

ID: 310785 / Support ID: 400097674
POWERLINK V1: Bug-fix for Up/Downgrade
POWERLINK V1 FW upgrade problem could be accoredafter PowerOn beginning with HW- Upgrade Version 1.3.1.0
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 311015 / Support ID: 400051206
Expansion: Link- selector flag
New datapoints:&lt;br/&gt;- RedundancyFirstLinkState&lt;br/&gt;- RedundancySecondLinkState
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(168), 1\9843_3.fw(168), 1\9843_4.fw(168)

Version 1.3.4.0:

ID: 305150 / Support ID: 400094368
ACOPOSmulti with SafeMC, asynchronous communication lost
When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(167), 1\9843_3.fw(167), 1\9843_4.fw(167)

Version 1.3.3.0:

ID: 298985/ Support ID: 400090781
Problem with FW-Update of IO modules on Powerlink buscontrollers
The firmware update of IO modules does not work in certain configurations.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(165), 1\9843_3.fw(165), 1\9843_4.fw(165)

Version 1.3.2.0:

ID: 160985
Additional diagnostic data points
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 291890 / Support ID: 400087996
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmwarechanged: Yes
Firmware: 1\9843_2.fw(164), 1\9843_3.fw(164), 1\9843_4.fw(164)

Version 1.3.1.0:

ID: 289015
Certain X2X configurations don't work
In very rare I/O constellations, the X2X modules don't start
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 290080
New Hardwarevariant 4
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(163), 1\9843_3.fw(163),1\9843_4.fw(163)

Version 1.3.0.0:

ID: 277175
Support of 'Multiple Asynchronous Send'
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 277745
New X2X datapoints
- NettimeOffsetX2X and NettimeX2X
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(160), 1\9843_3.fw(160)

Version 1.2.0.0:

ID: 246550
DNA support; Update behavior on X2X bus of the BC improved
- DNA support (Dynamic Node Allocation)
- faster updating of modules with big FW files on the X2X bus of the BC
- new objects: 20A3h and 2000h/9
Channel description changed: Yes
Configurationdescription changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(152), 1\9843_3.fw(152)

Version 1.0.9.0:

ID: 220630
Extensions and Bugfixes
- Combination of PollResponse-Chaining and PollRequest-Synchronization did not work correctly (A&P 218765)
Channel descriptionchanged: No
Configuration description changed: No
Firmware changed:Yes
Firmware: 1\9843_2.fw(146)

Version 1.0.8.0:

ID: 218500
Extensions and Bugfixes
- Firmware-Version is transferred via IdentResponse in the first 4 bytes ofthe field VendorSpecificExt1
- Supportof PollResponse-Chaining
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(145)

Version 1.0.7.0:

ID: 214455
Extensions and Bugfixes
- In systems with high X2X load it happened that IO modules were not restarted when the CPU did a warmstart (A&P 211805)
- Activation of MultipleRead/Write feature for faster startup after configuration change
- Writing to Objekt 20F0h/SubIndex 22 caused SDO errors when accessed faster than allowed
- Number of configuration entries per IO module changed from 100 to 155
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(144)

Version 1.0.6.0:

ID: 210960
Extensions and Bugfixes
- Error correction for operation in Powerlink V1 networks (A&P 210765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(143)

Version 1.0.4.0:

ID: 183385
New info-/diagnostic data points, new FW 1.39 for signal filterand corrections
New info-/diagnostic data points in HWC, new FW 1.39 forsignal filter and corrections
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(141)

Version 1.0.3.0:

ID: 173305
Extensions and Bugfixes
- Improvement of X2X Timings (Jitter reduced from 180ns to 20ns) (A&P167857 und 171987)
- Optimizations for operation in 200us networks
- 2 nodes with the same node number generated disturbance on the network (A&P 166040)
- Functions for a new firmware download mechanism implemented(A&P 168537)
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(138)

Version 1.0.2.0:

ID: 164665
Extensions
- Extensions for operation with Safety
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(136)
Verze Jazyk
Operační systém
Datum
Velikost
Typ Stáhnout
2.6.0.0 * 02.02.2018 2 MB EXE AS3.0_HW_X20BC8083.exe
Popis V3.0 HW Upgrade (X20BC8083)

Revision information X20BC8083

Version 2.6.0.0:

ID: 574215
Optimization of boot procedure for hardware variant 5 und 6
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(423), 1\9843_3.fw(423), 1\9843_4.fw(423), 1\9843_5.fw(423), 1\9843_6.fw(423)

Version 2.5.6.0:

ID: 564800
Optimization the boot up for hardware variant 5
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(422), 1\9843_3.fw(422), 1\9843_4.fw(422), 1\9843_5.fw(422)

Version 2.5.5.0:

ID: 551115
Startup time optimizations
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(421), 1\9843_3.fw(421), 1\9843_4.fw(421), 1\9843_5.fw(421)

Version 2.5.4.0:

ID: 540310 / Support ID: 400202320
BC sporadically not going into Operational due to X2X-bus problems at startup
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(419), 1\9843_3.fw(419), 1\9843_4.fw(419)

Version 2.5.3.0:

ID: 523465 / Support ID: 400205694
safety modules not switching to operational state
SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(417), 1\9843_3.fw(417), 1\9843_4.fw(417)

Version 2.5.2.0:

ID: 493880 / Support ID: 400103115, 400101850, 400154063, 400190752
First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(415), 1\9843_3.fw(415), 1\9843_4.fw(415)

Version 2.5.0.0:

ID: 468040 / Support ID: 400178654
Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468045 / Support ID:400177243
X2X FW update of several X2X modules is not working
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468050
optimization of X2X FW updates
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 468525
CiR support
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(413), 1\9843_3.fw(413), 1\9843_4.fw(413)

Version 2.3.0.0:

ID: 460100 / Support ID: 400168329
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 460220 / Support ID: 400150525
Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 462080
Module documentation revised
Data sheet V 2.32
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(411), 1\9843_3.fw(411), 1\9843_4.fw(411)

Version 2.2.1.0:

ID: 445325 / Support ID: 400162116
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 448525 / Support ID: 400164639
When combining X20BC8083 with Version 2.2.0.0 and X20HB2881 no PLK connection is available
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_2.fw(401), 1\9843_3.fw(401), 1\9843_4.fw(401)

Version 2.2.0.0:

ID: 439095 / Support ID: 400150496
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 439200 / Support ID: 400128436
I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(400), 1\9843_3.fw(400), 1\9843_4.fw(400)

Version 2.1.0.0:

ID: 404500
X2XLink-BC: StationAtBusEnd does not change,when empty backplanes are addedor removed.
When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change.
The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 2.0.0.0:

ID: 390270 / Support ID: 400129274
Uncommon X2X settings cause permanent boot ofbus controller
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(210), 1\9843_3.fw(210), 1\9843_4.fw(210)

Version 1.3.5.0:

ID: 310785/ Support ID: 400097674
POWERLINK V1: Bug-fix for Up/Downgrade
POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 311015 / Support ID: 400051206
Expansion: Link- selector flag
New datapoints:&lt;br/&gt;- RedundancyFirstLinkState&lt;br/&gt;- RedundancySecondLinkState
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\9843_2.fw(168), 1\9843_3.fw(168), 1\9843_4.fw(168)

Version 1.3.4.0:

ID: 305150 / Support ID: 400094368
ACOPOSmulti with SafeMC, asynchronous communication lost
When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted. Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(167), 1\9843_3.fw(167), 1\9843_4.fw(167)

Version 1.3.3.0:

ID: 298985 / Support ID: 400090781
Problem with FW-Update of IO modules on Powerlink buscontrollers
The firmwareupdate of IO modules does not work in certain configurations.
Channel description changed: No
Configuration description changed: No
Firmwarechanged: Yes
Firmware: 1\9843_2.fw(165), 1\9843_3.fw(165), 1\9843_4.fw(165)

Version 1.3.2.0:

ID: 160985
Additional diagnostic data points
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 291890 / Support ID: 400087996
Error when running X20BC8083 (Rev. < G0) in base module X20BB80
Correction with new firmware
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(164), 1\9843_3.fw(164), 1\9843_4.fw(164)

Version 1.3.1.0:

ID: 289015
Certain X2X configurations don't work
In very rare I/Oconstellations, the X2X modules don't start
Channel description changed:No
Configuration description changed: No
Firmware changed: Yes

ID: 290080
New Hardwarevariant 4
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(163), 1\9843_3.fw(163), 1\9843_4.fw(163)

Version 1.3.0.0:

ID: 277175
Support of 'Multiple Asynchronous Send'
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 277745
New X2X datapoints
- NettimeOffsetX2X and NettimeX2X
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(160), 1\9843_3.fw(160)

Version 1.2.0.0:

ID: 246550
DNA support; Update behavior on X2X bus of the BC improved
- DNA support (Dynamic Node Allocation)
- faster updating of modules with big FW files on the X2X bus of the BC
- new objects: 20A3h and 2000h/9
Channeldescription changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\9843_2.fw(152), 1\9843_3.fw(152)

Version 1.0.9.0:

ID: 220630
Extensions and Bugfixes
- Combination of PollResponse-Chaining and PollRequest-Synchronization did not work correctly (A&P 218765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_2.fw(146)

Version 1.0.8.0:

ID: 218500
Extensions and Bugfixes
- Firmware-Version is transferred via IdentResponse in the first 4 bytes ofthe field VendorSpecificExt1
- Support of PollResponse-Chaining
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(145)

Version 1.0.7.0:

ID: 214455
Extensions and Bugfixes
- In systems with high X2X load it happened that IO modules were not restarted when the CPU did a warmstart (A&P 211805)
- Activation of MultipleRead/Write feature for faster startup after configuration change
- Writing to Objekt 20F0h/SubIndex 22 caused SDO errors when accessed faster than allowed
- Number of configuration entries per IO module changed from 100 to 155
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(144)

Version 1.0.6.0:

ID: 210960
Extensions and Bugfixes
- Error correction for operation in Powerlink V1 networks (A&P 210765)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\9843_1.fw(143)

Version 1.0.4.0:

ID: 183385
New info-/diagnostic data points, new FW 1.39 for signal filter and corrections
New info-/diagnostic data points in HWC, new FW 1.39 for signal filter and corrections
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(141)

Version 1.0.3.0:

ID: 173305
Extensions and Bugfixes
- Improvement of X2X Timings (Jitter reduced from 180ns to 20ns) (A&P167857 und 171987)
- Optimizations for operation in 200us networks
- 2 nodes with the same node number generated disturbance on the network (A&P 166040)
- Functions for anew firmware download mechanism implemented (A&P 168537)
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(138)

Version 1.0.2.0:

ID: 164665
Extensions
- Extensions for operation with Safety
Channeldescription changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\9843_1.fw(136)
Loading
Zpět k seznamu

Vyberte prosím zemi a jazyk

B&R Logo