DWL@DWL10000310394
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
---|---|---|---|---|---|---|
1.3.0.0 | * | 10.09.2015 | 615 KB | EXE | AS2.6_HW_5LS182.6-1.exe | |
Popis |
V2.7 HW Upgrade (5LS182.6-1) Revision information 5LS182.6-1 Version 1.3.0.0: ID: 444120 POWERLINK V2 operating mode: managing node An error is causing higher transfer times on the PCI bus that are resultingin POWERLINK and I/O cycle time violations. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(17178), 1\8530a0.epl(67) Version 1.2.7.0: ID: 429215 Support Bonding feature Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 429230 / Support ID: 400151182 POWERLINK V2: "Controlled node" mode In networks with heavy SoC jitter, the dropping out of an SoC sometimes caused a permanent freezing of the input data on the controlled node. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(16922), 1\8530a0.epl(66) Version 1.2.6.0: ID: 391570 Possibly incorrect display of the Powerlink status LEDs Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(16410), 1\8530a0.epl(64) Version 1.2.5.0: ID: 377985 Module sporadically not recognized in APC910 when booting Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(16409), 1\8530a0.epl(64) Version 1.2.3.0: ID: 332295 / Support ID: 400092134 POWERLINK V1: If the "Activate Ethernet communication off" option is enabled, asynchronous POWERLINK communication fails in some circumstances. The following configuration may cause asynchronous communication to fail: - POWERLINK V1 - "Activate Ethernet communication off" - POWERLINK CNs on the network thatalso support POWERLINK V2 This upgrade can be installed to resolve this problem. It is also possible toset "Activate Ethernet communication" to "On". Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 336705 POWERLINK V2 MN mode: It was possible that an undefined state occurred during booting that causedthe interface to fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 337435 / Support ID: 400108118 POWERLINK V2 CN mode It was possible that an undefined state occurred during booting that causedthe interface to fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(16151), 1\8530a0.epl(63) Version 1.2.2.1: ID: 285935 POWERLINK V2 CN mode: Asynchronous packets lost when there is a large asynchronous load with large asynchronous frames. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(15383), 1\8530a0.epl(60) Version 1.2.2.0: ID: 283950 POWERLINK V2: Large fluctuations of IEEE 1588 Nettime (used for safety logbook entries) during startup. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 284285 / Support ID: 400032936 SRAM acess via PCI accelerated. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(15127), 1\8530a0.epl(59) Version 1.2.0.2: ID: 256795 / Support ID: 400057319 POWERLINK: In controlled node mode, the I/O mapping was not applied when the manager was restarted. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 256910 POWERLINK: LinkOK data point added. Channel description changed: Yes Configuration description changed:No Firmware changed: No ID: 256950 POWERLINK: The net timeis not always transferred correctly to the application. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 265690 POWERLINK V2 CN mode: Frequent MN failures result in CPU going into Servicemode. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID:265885 POWERLINK V2: If the the Ready-Flag was canceled on the network, the ModuleOK was not cleared. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 265360 Warning 32168 "POWERLINK V2: Invalid frame format" on iCN with "Chaned Station" on the same network Error correction: When an iCN is used in the same POWERLINK network with a "Chained Station", there may be warnings 32168 in the logger. The reason for this warning is that the sync response frames that are used to measure the timing of the "Chained Station" are not recognized by the iCN. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(14870), 1\8530a0.epl(58) Version 1.1.16.0: ID: 243767 Parameter "OutputDMAMargin" activated for B3.07 Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(13333), 1\8530a0.epl(52) Version 1.1.15.0: ID: 243320 / Support ID: 400054385 FW1.1.14.2 of the LS 182.6-1 tends to invalid Datapoints Error in the .hwc Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(13333), 1\8530a0.epl(52) Version 1.1.14.2: ID: 241602 PCI diagnosis and new data points added; + Synchronization problem in TK#1 fixed In various projects, a cycle time violation occurredoccasionally. New data points: - PCILoadPercentFirstHalf - PCILoadPercentSecondHalf - OutputDMAMargin Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\8530_0.pci(13333), 1\8530a0.epl(52) Version 1.1.13.1: ID: 233170 / Support ID: 400046653 Reset behavior improved and new data points created Error correction: After a restart, the default firmware was loaded and thenupdated again. New data points: - SerialNumber - ModuleID - HardwareVariant - FirmwareVersion Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(13332), 1\8530a0.epl(52) Version 1.1.12.0: ID: 230835 POWERLINK V2 CN mode: Frequent MN failures result in CPU going into Servicemode. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(13331), 1\8530a0.epl(52) Version 1.1.9.0: ID: 220050 / Support ID: 400035362 POWERLINK V2: Boot behavior improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(13075), 1\8530a0.epl(51) Version 1.1.8.0: ID: 213025 CN mode: Various error corrections made. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(12051), 1\8530a0.epl(47) Version 1.1.7.0: ID:206905 New POWERLINK firmware V45 and basis firmware V19 POWERLINK V2 CN mode: - Frequent MN failures result in CPU going into Service mode. - The PollResponse data from multiplexed stations are now updated in every POWERLINK cycle. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(11539), 1\8530a0.epl(45) Version 1.1.6.0: ID: 199520 New POWERLINK V1/V2 firmware V44 CN mode: Various error corrections made. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\8530_0.pci(11282), 1\8530a0.epl(44) Version 1.1.5.1: ID: 191740 New POWERLINK V1/V2 Firmware V42 - Error correction for POWERLINK V2: After network disturbances, failed stations were left out of cyclic traffic. - Error correction POWERLINKV2 CN mode: Failure of a SoC resulted immediately in incorrect failure detection by manager. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(10770), 1\8530a0.epl(42) Version 1.1.4.1: ID: 185045 New POWERLINK V1/V2 firmware V39 and basis firmware V18 - Error correction for POWERLINK V2: Certain configurations may cause multiplexed stations to fail. - Error correction for POWERLINK V2: An error while switching the alternating buffer caused old input data to be resent. (This error only occurred with upgrade 1.1.3.0.) - Error correction: In configurations with a large amount of I/O data, incorrect input data was sent. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(10002), 1\8530a0.epl(39) Version 1.1.3.0: ID: 183600 New POWERLINK V1/V2 firmware V38 and basis firmware V16 - Error correction for POWERLINK V2: Parameter "CycleIdleTime" was not calculated correctly. - Error correction: ModbusTCP on POWERLINK interfaces was not working. - Improved stability for network disturbances. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(9744), 1\8530a0.epl(38) Version 1.1.2.0: ID: 174655 New POWERLINK V1/V2 firmware V37 and base firmware V15 Error corrections: - In large networks, ring redundancy may not work in some circumstances. - POWERLINK V2 CN mode: Various error corrections made. - Asynchronous scheduler: The host has only sent anasynchronous frame in max. every second cycle. - POWERLILNK V2: Asynchronous frames can now be received with the Powerlinklibrary starting with channel >= 0x20 (previously starting with 0xA0). Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(9487), 1\8530a0.epl(37) Version 1.1.1.0: ID: 173330 New POWERLINK firmware V36 Error correction: - Whenusing an I/O prescaler > 1, in certain circumstances the old input data for the station is provided to the application. - ISSI-RAMs are supported. Changes - POWERLINK V2: - The poll response from the manager is now sent at the beginning of the POWERLINK cycle. - From now on, stations are addressed with poll requests starting in status"PreOperational 2". Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(9230), 1\8530a0.epl(36) Version 1.1.0.0: ID: 170735 Performance improvement - POWERLINK manager Channel description changed: No Configuration descriptionchanged: No Firmware changed: No Firmware: 1\8530_0.pci(8973), 1\8530a0.epl(35) Version 1.0.6.0: ID: 167140 New base firmware V11 Collisions resulted in transmission of invalid frames. Channeldescription changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(8715), 1\8530a0.epl(34) Version 1.0.5.0: ID: 165810 New POWERLINK V1/V2 Firmware V34 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(8714), 1\8530a0.epl(34) Version 1.0.4.0: ID: 165450 New POWERLINK V1/V2 Firmware V33 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(8458), 1\8530a0.epl(33) Version 1.0.3.0: ID: 164765 New POWERLINK V1/V2 Firmware V31 - Optimizations for EPL V2 startup carried out. - Nettime IEEE1588 for EPL V2 implemented. - From now on, the asynchronous scheduler will handle asynchronous requestsbased on their priority. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(7946), 1\8530a0.epl(31) Version 1.0.1.0: ID: 160750 New POWERLINK V1/V2 Firmware V30 In "Controlled Node" mode, the following errors may occur: - With heavy asynchronous loads, asynchronous TX packets may be lost. - Collisions on the network can cause the station to stop receiving Ethernet packets. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\8530_0.pci(7690), 1\8530a0.epl(30) |