Lütfen ülke ve dil seçiniz

Short description
I/O module 4 digital inputs, 2 digital outputs, 1 input for full-bridge strain gauge
General information
B&R ID code 0x1CDF
Status indicators I/O function for each channel, supply voltage, bus function
Outputs Yes, using status LED
I/O power supply Yes, using status LED and software
Connection type
X2X Link M12, B-keyed
Inputs/Outputs 4x M12, A-keyed
I/O power supply M8, 4-pin
Power consumption
Internal I/O 1 W
X2X Link power supply 0.75 W
CE Yes
ATEX Zone 2, II 3G Ex nA IIA T5 Gc
IP67, Ta = 0 - Max. 60°C
TÜV 05 ATEX 7201X
UL cULus E115267
Industrial control equipment
HazLoc cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5
KC Yes
I/O power supply
Nominal voltage 24 VDC ±25%
Integrated protection Reverse polarity protection
Power consumption
Sensor power supply Max. 12 W
Strain gauge supply
Voltage 4.422 VDC / max. 60 mA
Voltage drop for short-circuit protection at 60 mA Max. 0.36 VDC
Short-circuit proof Yes
Sensor/Actuator power supply
Voltage I/O power supply minus voltage drop for short circuit protection
Voltage drop for short-circuit protection at 0.5 A Max. 2 VDC
Summation current Max. 0.5 A
Short-circuit proof Yes
Full-bridge strain gauge
Strain gauge factor ±15.625 to ±125 mV/V, configurable using software
Input type Differential, used to evaluate a full-bridge strain gauge
Digital converter resolution 24-bit
Conversion time Depends on the configured data output rate
Data output rate 10 to 3750 samples per second, configurable using software
Input filter
Cutoff frequency 50 kHz
Order 1
Slope 20 dB
Operating range / Measurement sensor 75 to 5000 Ω
Influence of cable length The shielded twisted pair cable should be as short as possible and run separately to the sensor (isolated from load circuit) without intermediate terminals
Input protection RC protection
Input current 450 nA
Common-mode range 0 to 3 VDC
Permissible input voltage range (with regard to the potential strain gauge GND) on the inputs "Input +" and "Input -"
Insulation voltage between input and bus 500 VEff
Gain 1 to 8, configurable using software
Conversion procedure Sigma-delta
Output of digital value
Broken bridge supply line Value approaches 0
Broken sensor line Value goes to ±limit
Valid range of values 0x7FFF FFFF to 0x8000 0001
Strain gauge supply
Voltage 4.5 VDC / max. 60 mA
Connection 4-wire connections
Short-circuit and overload resistant Yes
LSB value (16-bit)
69 mV/V 9.31 µV
138 mV/V 18.6 µV
276 mV/V 37.3 µV
553 mV/V 74.6 µV
LSB value (24-bit)
69 mV/V 36.4 nV
138 mV/V 72.8 nV
276 mV/V 146.0 nV
553 mV/V 251.0 nV
Temperature coefficient 50 ppm/°C
Digital inputs
Quantity 4
Nominal voltage 24 VDC
Input characteristics per EN 61131-2 Type 1
Input voltage 24 VDC ±25%
Input current at 24 VDC Typ. 5 mA
Input circuit Sink
Input filter
Hardware <1 ms
Software -
Input resistance Typ. 4.27 kΩ
Sensor power supply 0.5 A summation current
Switching threshold
Low <5 VDC
High >15 VDC
Insulation voltage between channel and bus 500 VEff
Digital outputs
Quantity 2
Nominal voltage 24 VDC
Switching voltage 24 VDC ±25%
Output circuit Source
Output protection Thermal cutoff for overcurrent and short circuit, integrated protection for switching inductances, reverse polarity protection for output power supply
Actuator power supply External
Insulation voltage between output and bus 500 VEff
Nominal output current
Output 1 0.5 A
Output 2 1 A
Output driver turn-on time
Output 1
Typical 50 µs
0 → 1 (90% VOut) Max. 100 µs
Output 2
Typical 60 µs
0 → 1 (90% VOut) Max. 160 µs
Switch-off time for output driver
Output 1
Typical 75 µs
1 → 0 (90% VOut) Max. 150 µs
Output 2
Typical 15 µs
1 → 0 (90% VOut) Max. 50 µs
Braking voltage when switching off inductive loads
Output 1 -47 VDC
Output 2 Approx. 1 VDC
Max. frequency
Output 1 100 Hz
Output 2 1 kHz
Electrical properties
Electrical isolation
Channel isolated from bus and digital isolated from analog

Digital not isolated from I/O power supply
Operating conditions
Mounting orientation
Any Yes
Installation elevation above sea level
0 to 2000 m No limitations
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP67
Ambient conditions
Operation -25 to 60°C
Storage -40 to 85°C
Transport -40 to 85°C
Mechanical properties
Width 53 mm
Height 85 mm
Depth 42 mm
Weight 200 g
Torque for connections
M8 Max. 0.4 Nm
M12 Max. 0.6 Nm
Malzeme Numarası:
  • 1 strain gauge input with 24-bit resolution
  • High data output rate (10 to 3,750 Hz)
  • Adjustable gain
  • 1 high-side output 24 VDC, 0.5 A
  • 1 high-side output 24 VDC, 1.0 A

This module enables the remote connection of a force gauge using a strain gauge with a converter resolution of up to 24-bit. The data rate can be set from 0.26 ms to 100 ms. This module concept requires compensation in the measurement system. This compensation eliminates the absolute uncertainty in the measurement circuit, such as component tolerances, effective bridge voltage or zero point offset. The measurement precision refers to the absolute (compensated) value, which will only change as a result of changes in the operating temperature. The module is also equipped with 4 digital inputs and 2 digital outputs.

Automation Studio Donanım Güncellemeleri Version (Date) Download
V2.6 HW Upgrade (X67UM1352) EXE / 1 MB
V3.0 HW Upgrade (X67UM1352) EXE / 2 MB
V4.0 HW Upgrade (X67UM1352) EXE / 1 MB
Dokümantasyon Version (Date) Download
Datasheet X67UM1352 PDF / 513 KB
X67 System User´s Manual PDF / 19 MB
E-CAD (Elektrik veya EPLAN Taslakları) Version (Date) Download
X67 EPLAN P8 EXE / 85 MB
X67 EPLAN P8 from V2.4 EXE / 105 MB
M-CAD (Mekanik Taslaklar) Version (Date) Download
3D File DXF/STEP X67 ZIP / 1 MB
Sertifikalar Version (Date) Download
244665 CSA HazLoc Certificate of Compliance X20, X67 PDF / 56 KB
E115267 UL CoC X67 PDF / 84 KB
TÜV 05 ATEX 7201 X PDF / 129 KB

Lütfen ülke ve dil seçiniz

B&R Logo