Short description
Communication module 1x RS232 or 1x RS485/RS422, 2 digital inputs, 2 digital channels configurable as inputs or outputs using software
General information
Insulation voltage between channel and bus 500 Veff
B&R ID code 0xA90F
Sensor/Actuator power supply 0.5 A summation current
Status indicators RS232, RS485/RS422, I/O function per channel, supply voltage, bus function
Diagnostics
Outputs Yes, using LED status indicator and software
I/O power supply Yes, using LED status indicator and software
RS232 Yes, using LED status indicator
RS485/RS422 Yes, using LED status indicator
Connection type
X2X Link M12, B-coded
Interfaces and inputs/outputs 4x M12, A-coded
I/O power supply M8, 4-pin
Power consumption
Internal I/O 2.4 W
X2X Link power supply 0.75 W
Certifications
CE Yes
UKCA Yes
ATEX Zone 2, II 3G Ex nA IIA T5 Gc
IP67, Ta = 0 - Max. 60°C
TÜV 05 ATEX 7201X
UL cULus E115267
Industrial control equipment
HazLoc cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5
EAC Yes
KC Yes
Interfaces
Interface IF1
Signal RS232
Max. distance 900 m
Transfer rate Max. 115.2 kbit/s
FIFO buffer Software
Handshake lines No
Interface IF2
Signal RS485/RS422
Max. distance 1200 m
Transfer rate Max. 115.2 kbit/s
FIFO buffer Software
Terminating resistor Integrated in module
I/O power supply
Nominal voltage 24 VDC
Voltage range 18 to 30 VDC
Integrated protection Reverse polarity protection
Power consumption
Sensor/Actuator power supply Max. 12 W
Sensor/Actuator power supply
Voltage I/O power supply minus voltage drop for short-circuit protection
Voltage drop for short-circuit protection at 0.5 A Max. 2 VDC
Summation current Max. 0.5 A
Short-circuit proof Yes
Digital inputs
Quantity Up to 4 if the 2 digital channels are used as digital inputs
Nominal voltage 24 VDC
Input characteristics per EN 61131-2 Type 1
Input voltage 18 to 30 VDC
Input current at 24 VDC Typ. 3.5 mA
Input circuit Sink
Input filter
Hardware ≤100 µs
Software Default 0 ms, configurable between 0 and 25 ms in 0.2 ms intervals
Input resistance Typ. 6.67 kΩ
Switching threshold
Low <5 V
High >15 VDC
Digital outputs
Quantity Up to 2 if the 2 digital channels are used as digital outputs
Variant Current-sourcing FET
Nominal voltage 24 VDC
Switching voltage I/O power supply minus residual voltage
Nominal output current 0.5 A
Total nominal current 1 A
Output circuit Source
Output protection Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads, reverse polarity protection of the output power supply
Diagnostic status Output monitoring with 10 ms delay
Leakage current when the output is switched off <120 μA
Peak short-circuit current <2.1 A
Switch-on in the event of overload shutdown or short-circuit shutdown Approx. 1 ms (depends on the module temperature)
Switching delay
0 → 1 <100 μs
1 → 0 <150 μs
Switching frequency
Resistive load Max. 1000 Hz
Inductive load See section "Switching inductive loads".
Braking voltage when switching off inductive loads Typ. 68 VDC
Electrical properties
Electrical isolation
Bus isolated from channel and IF

Channel not isolated from channel and IF
Operating conditions
Mounting orientation
Any Yes
Installation elevation above sea level
0 to 2000 m No limitation
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP67
Ambient conditions
Temperature
Operation -25 to 60°C
Derating -
Storage -40 to 85°C
Transport -40 to 85°C
Mechanical properties
Dimensions
Width 53 mm
Height 85 mm
Depth 42 mm
Weight 195 g
Torque for connections
M8 Max. 0.4 Nm
M12 Max. 0.6 Nm
Malzeme numarası:
X67IF1121-1
Açıklama:
  • RS232 and RS485/RS422 usable in parallel
  • 2 digital channels, configurable as inputs or outputs
  • 2 digital inputs
  • Connection of barcode readers, ID systems and sensors on one module

Serial interfaces (barcode scanners for example) are often scattered throughout systems. This interface module from the remote X67 system is the optimal choice for this area of application: RS232 and RS485/RS422 connection options directly where they are needed, distributed on the machine or system.

In addition, there are digital inputs and outputs on the same module so that corresponding 24 V sensors/actuators can also be connected.

Automation Studio donanım yükseltmeleri Sürüm (Tarih) İndirme
V2.7 HW Upgrade (X67IF1121-1) EXE / 448 KB
V2.7 HW Upgrade (X67IF1121-1) EXE / 3 MB
V3.0 HW Upgrade (X67IF1121-1) EXE / 447 KB
V3.0 HW Upgrade (X67IF1121-1) EXE / 5 MB
V4.0 HW Upgrade (X67IF1121-1) EXE / 4 MB
Dökümantasyon Sürüm (Tarih) İndirme
Datasheet X67IF1121-1 PDF / 950 KB
Installation- / EMC-Guide PDF / 20 MB
X67 System User´s Manual PDF / 6 MB
E-CAD (Elektro veya EPLAN şablonları) Sürüm (Tarih) İndirme
X67 EPLAN P8 from V2.4 EXE / 105 MB
M-CAD (Mechan. Şablonlar) Sürüm (Tarih) İndirme
3D File DXF/STEP X67 ZIP / 4 MB
Sertifikalar Sürüm (Tarih) İndirme
244665 CSA HazLoc CoC X20, X67 PDF / 158 KB
E115267 UL CoC X67 PDF / 155 KB
EU Declaration ATEX X67 PDF / 191 KB
EU Declaration PLC X67 PDF / 674 KB
TÜV 05 ATEX 7201 X PDF / 5 MB
UK Declaration PLC X67 PDF / 469 KB
X20, X67 KC certificates PDF / 6 MB

Lütfen ülke ve dil seçin

B&R Logo