General information
B&R ID code 0xA8E6
Support
Dynamic node allocation (DNA) Yes
Cooling and mounting type Wall mounting
Slots for plug-in modules 2
Certifications
CE Yes
UKCA Yes
Functional safety Yes
UL cULus E225616
Power conversion equipment
EAC Yes
KC Yes
DC bus connection
Voltage
Nominal 750 VDC
Continuous power consumption 32.37 kW
Power dissipation depending on switching frequency
Switching frequency 5 kHz [0.65 * IM² - 0.35 * IM+ 64] W
Switching frequency 10 kHz [2.16 * IM² - 10.912 * IM+ 190] W
DC bus capacitance 1320 µF
Variant ACOPOSmulti backplane
24 VDC power supply
Input voltage 25 VDC ±1.6%
Input capacitance 23.5 µF
Max. power consumption 21 W + PSLOT1 + PSLOT2 + P24 V Out + PHoldingBrake(s)
Variant ACOPOSmulti backplane
24 VDC output
Quantity 2
Output voltage
DC bus voltage (UDC): 260 to 315 VDC 25 VDC * (UDC/315)
DC bus voltage (UDC): 315 to 800 VDC 24 VDC ±6%
Fuse protection 250 mA (slow-blow) electronic, automatic reset
Motor connection
Quantity 2
Continuous power per motor connection 16 kW
Continuous current per motor connection 22 Aeff
Reduction of continuous current depending on switching frequency
Switching frequency 5 kHz 0.33 A/K (starting at 40°C)
Switching frequency 10 kHz 0.17 A/K (starting at -25°C)
Reduction of continuous current depending on installation elevation
Starting at 500 m above sea level 2.2 Aeff per 1000 m
Peak current per motor connection 55 Aeff
Nominal switching frequency 5 kHz
Possible switching frequencies 5 / 10 kHz
Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
Protective measures
Overload protection Yes
Short-circuit and ground fault protection Yes
Max. output frequency 598 Hz
Variant
U, V, W, PE Connector
Shield connection Yes
Terminal connection cross section
Flexible and fine-stranded wires
With wire end sleeves 0.25 to 6 mm²
Approbation data
UL/C-UL-US 30 to 10 AWG
CSA 28 to 10 AWG
Terminal cable cross section dimension of shield connection 12 to 22 mm
Max. motor line length depending on switching frequency
Switching frequency 5 kHz 25 m
Switching frequency 10 kHz 25 m
Motor holding brake connection
Quantity 2
Output voltage 24 VDC +5.8% / -0%
Continuous current per connection 2.1 A
Max. internal resistance 0.3 Ω
Extinction potential Approx. 30 V
Max. extinction energy per switching operation 3 Ws
Max. switching frequency 0.5 Hz
Protective measures
Overload and short-circuit protection Yes
Open-circuit monitoring Yes
Undervoltage monitoring Yes
Response threshold for open-circuit monitoring Approx. 0.5 A
Response threshold for undervoltage monitoring 24 VDC +0% / -4%
Enable inputs
Quantity 4 (2 per axis)
Circuit Sink
Electrical isolation
Input - Inverter module Yes
Input - Input Yes
Input voltage
Nominal 24 VDC
Maximum 30 VDC
Input current at nominal voltage Approx. 30 mA
Switching threshold
Low <5 V
High >15 V
Switching delay at nominal input voltage
Enable 1 → 0, PWM off Max. 20.5 ms
Enable 0 → 1, ready for PWM Max. 100 µs
Modulation compared to ground potential Max. ±38 V
OSSD signal connections Permitted
Max. test pulse length: 500 µs
Trigger inputs
Quantity 2
Circuit Sink
Electrical isolation
Input - Inverter module Yes
Input - Input Yes
Input voltage
Nominal 24 VDC
Maximum 30 VDC
Switching threshold
Low <5 V
High >15 V
Input current at nominal voltage Approx. 10 mA
Switching delay
Rising edge 52 µs ±0.5 µs (digitally filtered)
Falling edge 53 µs ±0.5 µs (digitally filtered)
Modulation compared to ground potential Max. ±38 V
Temperature sensor connection
Quantity 2
Resistance range 500 Ω to 5 kΩ
Electrical properties
Discharge capacitance 0.44 µF
Operating conditions
Permissible mounting orientations
Hanging vertically Yes
Horizontal, face up Yes
Standing horizontally No
Installation elevation above sea level
Nominal 0 to 500 m
Maximum 4000 m
Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
Overvoltage category per EN 61800-5-1 III
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Nominal 5 to 40°C
Maximum 55°C
Storage -25 to 55°C
Transport -25 to 70°C
Relative humidity
Operation 5 to 85%
Storage 5 to 95%
Transport Max. 95% at 40°C
Mechanical properties
Dimensions
Width 106.5 mm
Height 317 mm
Depth
Wall mounting 263 mm
Weight Approx. 5.7 kg
Module width 2
Номер модель:
8BVI0220HWD0.000-1
Описание:
  • Integrated uncontrolled standstill and safe stop
  • Integrated connection for motor holding brake and temperature sensor
  • 2 slots for ACOPOSmulti plug-in modules
  • Two fully independent power inverters in one inverter module contained in 2-axis modules
ACOPOSmulti inverter module, 22 A, AS, wall mounting, 2 axes
Обязательные аксессуары
Terminal block sets
8BZVI0220D0.000-1A Screw clamp terminal block set for ACOPOSmulti 8BVI0220HxD0 modules: 1x 8TB2112.2010-00, 1x 8TB2108.2010-00, 1x 8TB2104.203L-00, 1x 8TB2104.203F-00, 1x 8TB3104.204G-11, 1x 8TB3104.204K-11
Дополнительные аксессуары
Accessory sets
8BXB000.0000-00 ACOPOSmulti accessory set for encoder buffering consisting of: 1x battery AA 3.6 V, 1x protective cover for battery holder
Fan modules
8BXF001.0000-00 Модуль вентилятора для ACOPOSmulti, сменный вентилятор для модулей ACOPOSmulti (8BxP/8B0C/8BVI/8BVE/8B0K)
POWERLINK/Ethernet cables
X20CA0E61.00020 Соединительный кабель POWERLINK/Ethernet, RJ45 – RJ45, длина 0,2 м
X20CA0E61.00025 Соединительный кабель POWERLINK, RJ45 – RJ45, 0,25 м
X20CA0E61.00030 Соединительный кабель POWERLINK, RJ45 – RJ45, 0,3 м
X20CA0E61.00035 Соединительный кабель POWERLINK, RJ45 – RJ45, 0,35 м
X20CA0E61.00050 Соединительный кабель POWERLINK/Ethernet, RJ45 – RJ45, длина 0,5 м
X20CA0E61.00100 Соединительный кабель POWERLINK/Ethernet, RJ45 – RJ45, длина 1 м
Plug-in modules
8BAC0120.000-1 ACOPOSmulti plug-in module, EnDat 2.1 interface
8BAC0120.001-2 ACOPOSmulti plug-in module, EnDat 2.2 interface
8BAC0121.000-1 ACOPOSmulti plug-in module, HIPERFACE interface
8BAC0122.000-1 ACOPOSmulti plug-in module, resolver interface 10 kHz
8BAC0123.000-1 ACOPOSmulti plug-in module, incremental encoder and SSI absolute encoder interface for RS422 signals
8BAC0123.001-1 ACOPOSmulti plug-in module, incremental encoder interface for 5 V single-ended and 5 V differential signals
8BAC0123.002-1 ACOPOSmulti plug-in module, incremental encoder interface for 24 V single-ended and 24 V differential signals
8BAC0124.000-1 ACOPOSmulti plug-in module, SinCos interface
8BAC0125.000-1 ACOPOSmulti plug-in module, SinCos EnDat 2.1/SSI/BiSS interface
8BAC0130.000-1 ACOPOSmulti plug-in module, 2 digital outputs, 50 mA, max. 62.5 kHz, 2 digital outputs, 500 mA, max. 1.25 kHz, 2 digital inputs 24 VDC
8BAC0130.001-1 ACOPOSmulti plug-in module, 2 digital outputs, 50 mA, max. 62.5 kHz, 4 digital outputs, 500 mA, max 1.25 kHz
8BAC0132.000-1 ACOPOSmulti plug-in module, 4 analog inputs ±10 V
8BAC0133.000-1 ACOPOSmulti plug-in module, 3 RS422 outputs for ABR encoder emulation, 1 MHz
Shield component sets
8SCS000.0000-00 Набор компонентов для экранирования ACOPOSmulti: 1 пластина для крепления экрана 1x тип 0, 1 хомут для кабеля, B 9 мм, D 12-22 мм
8SCS002.0000-00 Набор компонентов для экранирования ACOPOSmulti: 1 зажимная планка, 2 хомута D 4-13,5 мм, 2 винта
8SCS005.0000-00 ACOPOSmulti shield component set: 1x slot cover / shield plate
8SCS009.0000-00 Набор компонентов для экранирования ACOPOSmulti: 1 пластина для крепления экрана ACOPOSmulti SK8-14, 1 зажим для крепления экрана SK14
Terminal blocks
8TB2104.203F-00 4-pin screw clamp terminal block, 1-row, pitch: 5.08 mm, label 3: T- T+ B- B+, coding F: 0101
8TB2104.203L-00 4-pin screw clamp terminal block, 1-row, pitch: 5.08 mm, label 3: T- T+ B- B+, coding L: 1010
8TB2108.2010-00 8-контактная с винтовыми зажимами, однорядная, расстояние между контактами: 5,08 мм, метка 1: пронумерованы последовательно
8TB2112.2010-00 Клеммная колодка с винтовыми зажимами, 12-контактная, 1-рядная, расстояние между контактами: 5,08 мм, маркировка: порядковая нумерация
8TB3104.204G-11 4-pin screw clamp terminal block, 1-row, pitch: 7.62 mm, label 4: PE W V U, coding G: 0110
8TB3104.204K-11 4-pin screw clamp terminal block, 1-row, pitch: 7.62 mm, label 4: PE W V U, coding K: 1001
E-CAD (Electro или EPLAN шаблоны) Версия (Дата) Загрузка
ACOPOSmulti EPLAN P8 from V2.4 EXE / 81 МБ
M-CAD (Механические Шаблоны Версия (Дата) Загрузка
3D file STEP 8BVI0220HWD0.000-x ZIP / 185 кБ
Документация Версия (Дата) Загрузка
ACOPOSmulti User´s Manual PDF / 302 МБ
Datasheet 8BVI0220HWD0.000-1 PDF / 2 МБ
Обновление Automation Studio HW Версия (Дата) Загрузка
V3.0 HW Upgrade (8BVIxxxxxxDx.xxx-x) EXE / 396 кБ
V4.0 HW Upgrade (8BVI0220HWD0.000-1) EXE / 290 кБ
V4.0 HW Upgrade (8BVIxxxxxxDx.xxx-1) EXE / 582 кБ
V4.0 HW Upgrade (8BVIxxxxxxDx.xxx-x) EXE / 383 кБ
Сертификаты Версия (Дата) Загрузка
ACOPOSmulti KC certificates ZIP / 3 МБ
E225616 UL Certificate of Compliance ACOPOSmulti (UL 508C) PDF / 282 кБ
E225616 UL Certificate of Compliance ACOPOSmulti (UL 61800-5-1) PDF / 183 кБ
EAC Conformity declaration 8BVI servodrive PDF / 1 МБ
EU Declaration FS Servos ACOPOSmulti PDF / 233 кБ
EU Declaration Servos ACOPOSmulti PDF / 219 кБ
TÜV-certificate - function "Safe Pulse Disabling" for ACOPOSmulti ZIP / 1 МБ
UK Declaration FS Servos ACOPOSmulti PDF / 89 кБ
UK Declaration Servos ACOPOSmulti PDF / 109 кБ

Укажите страну и язык

B&R Logo