8B0C0320HC00.002-1

General information
Cooling and mounting type Cold plate or pass-through mounting
Certifications
CE Yes
UKCA Yes
UL cULus E225616
Power conversion equipment
EAC Yes
KC Yes
DC bus connection
Voltage
Nominal 750 VDC
Operating range in continuous operation 260 to 800 VDC
Full continuous power 315 to 800 VDC
Continuous power consumption Max. 880 W
Power dissipation with continuous power 22 W (0% continuous power)
35 W (50% continuous power)
80 W (100% continuous power)
DC bus capacitance 220 nF
Variant ACOPOSmulti backplane
24 VDC output
Continuous power 800 W
Output voltage
DC bus voltage (UDC): 260 to 315 VDC 25 VDC * (UDC / 315)
DC bus voltage (UDC): 315 to 800 VDC 24 VDC ±6%
Continuous current 32 ADC
Reduction of continuous power at ambient temperatures starting at 40°C No reduction
Reduction of continuous power depending on installation elevation
Starting at 500 m above sea level 80 W per 1000 m
Reduction of continuous power depending on cooling method No reduction
Startup delay Max. 1 s
Startup time Approx. 5 to 20 ms
Residual ripple Typ. 50 mVSS
24 VDC internal system power supply
Output voltage 25 VDC ±1.6%
Peak current (<4 s)
DC bus voltage (UDC): 350 to 800 VDC 42 ADC
Protective measures
No-load proof Yes
Overload-proof Yes
Short-circuit proof Yes
Feedback protection Max. 26 VDC (also when the power is switched off)
Overtemperature protection Yes
Dielectric strength to ground ±50 VDC
Output/Input isolation SELV / PELV requirements
Variant ACOPOSmulti backplane
24 VDC Out
Output voltage
DC bus voltage (UDC): 260 to 315 VDC 25 VDC * (UDC / 315)
DC bus voltage (UDC): 315 to 800 VDC 24 VDC ±6%
Protection of 24 VDC Out 1 output 32 A (slow-blow) electronic, automatic reset
Protection of 24 VDC Out 2 output 5 A (slow-blow) electronic, automatic reset
Protective measures
No-load proof Yes
Overload-proof Yes
Short-circuit proof Yes
Feedback protection Max. 35 VDC (also when the power is switched off)
Overtemperature protection Yes
Dielectric strength to ground ±50 VDC
Output/Input isolation SELV / PELV requirements
Variant
24 VDC, COM Connector
Terminal connection cross section of 24 VDC Out 1 output
Flexible and fine-stranded wires
With wire end sleeves 0.25 to 6 mm²
Approbation data
UL/C-UL-US 22 to 10 AWG
CSA 22 to 10 AWG
Terminal connection cross section of 24 VDC Out 2 output
Flexible and fine-stranded wires
With wire end sleeves 0.25 to 2.5 mm²
Approbation data
UL/C-UL-US 22 to 12 AWG
CSA 22 to 12 AWG
24 VDC Out 1 controller input
Circuit Sink
Electrical isolation
Input - 24 VDC Yes
Modulation compared to ground potential Max. ±50 V
Input voltage
Nominal 24 VDC
Maximum 30 VDC
Switching threshold
Low (24 VDC Out 1 is switched on) <5 V
High (24 VDC Out 1 is switched off) >15 V
Input current at nominal voltage Approx. 10 mA
Switching delay
ON (24 VDC Out 1 is switched on) Max. 25 ms
OFF (24 VDC Out 1 is switched off) Max. 0.25 ms
Variant Connector
Terminal connection cross sections
Flexible and fine-stranded wires
With wire end sleeves 0.25 to 2.5 mm²
Approbation data
UL/C-UL-US 30 to 12 AWG
CSA 22 to 12 AWG
Operating conditions
Permissible mounting orientations
Hanging vertically Yes
Horizontal, face up Yes
Standing horizontally No
Installation elevation above sea level
Nominal 0 to 500 m
Maximum 4000 m
Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
Overvoltage category per EN 61800-5-1 III
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Nominal 5 to 40°C
Maximum 55°C
Storage -25 to 55°C
Transport -25 to 70°C
Relative humidity
Operation 5 to 85%
Storage 5 to 95%
Transport Max. 95% at 40°C
Mechanical properties
Dimensions
Width 53 mm
Height 317 mm
Depth
Cold plate 212 mm
Pass-through mounting 209 mm
Weight Approx. 2.6 kg
Module width 1
Номер модель:
8B0C0320HC00.002-1
Описание:
  • Connections for supplying external 24 V devices
  • Extensive protective measures
ACOPOSmulti auxiliary supply module, 32 A, AS, cold plate or pass-through mounting, 24VOut 1x 32 A, 1x 5 A
Обязательные аксессуары
Terminal block sets
8BZ0C032000.002-1A Screw clamp terminal block set for ACOPOSmulti 8B0C0320Hx00.002-1 modules: 1x 8TB3104.201M-11, 1x 8TB2104.2010-00, 1x 8TB2106.2010-00
Дополнительные аксессуары
Fan modules
8BXF001.0000-00 Модуль вентилятора для ACOPOSmulti, сменный вентилятор для модулей ACOPOSmulti (8BxP/8B0C/8BVI/8BVE/8B0K)
Terminal blocks
8TB2104.2010-00 Клеммная колодка с винтовыми зажимами, 4-контактная, 1-рядная, расстояние между контактами: 5,08 мм, маркировка: порядковая нумерация
8TB2106.2010-00 6-pin screw clamp terminal block, 1-row, pitch: 5.08 mm, label 1: Numbered consecutively
8TB3104.201M-11 4-pin screw clamp terminal block, 1-row, pitch: 7.62 mm, label 1: Numbered consecutively, coding M: 1011
E-CAD (Electro или EPLAN шаблоны) Версия (Дата) Загрузка
ACOPOSmulti EPLAN P8 from V2.4 EXE / 81 МБ
M-CAD (Механические Шаблоны Версия (Дата) Загрузка
3D file STEP 8B0C0xx0HC00.00x-1 ZIP / 98 кБ
Документация Версия (Дата) Загрузка
ACOPOSmulti User´s Manual PDF / 302 МБ
Datasheet 8B0C0320HC00.002-1 PDF / 772 кБ
Сертификаты Версия (Дата) Загрузка
ACOPOSmulti KC certificates ZIP / 3 МБ
E225616 UL Certificate of Compliance ACOPOSmulti (UL 508C) PDF / 282 кБ
E225616 UL Certificate of Compliance ACOPOSmulti (UL 61800-5-1) PDF / 183 кБ
EAC Conformity declaration 8B power sources PDF / 1 МБ
EU Declaration Servos ACOPOSmulti PDF / 219 кБ
UK Declaration Servos ACOPOSmulti PDF / 109 кБ

Укажите страну и язык

B&R Logo