X20DMF320

Short description
I/O module 16 digital inputs 24 VDC for 1-wire connections
16 mixed channels, 24 VDC input or output for 1-wire connections
Interfaces 1x X2X Link
General information
B&R ID code 0x2E86
Status indicators I/O function per channel, operating state, module status
Diagnostics
Module run/error Yes, using LED status indicator and software
Outputs Yes, using LED status indicator and software (output state)
Power consumption
Bus 0.04 W
Internal I/O 2.7 W
Additional power dissipation caused by actuators (resistive) [W] 0.312 W
Certifications
CE Yes
UKCA Yes
CRA (Cyber Resilience Act) In preparation
UL cULus E115267
Industrial control equipment
Digital inputs
Quantity 6 high-speed inputs, 10 standard inputs
16 mixed channels, configuration as input or output using software
Nominal voltage 24 VDC
Input characteristics per EN 61131-2 Type 1
Input voltage 24 VDC -15% / +20%
Input current at 24 VDC Channels 1 to 6, high-speed inputs: Typ. 3.2 mA
Channels 7 to 16, standard inputs: Typ. 2.4 mA
Channels 17 to 32, mixed channel: Typ. 2.4 mA
Input circuit Sink
Input filter
Hardware High-speed inputs: ≤7 μs
Standard inputs and mixed channels: ≤100 μs
Software Default 0 ms, configurable between 0 and 25 ms in 0.1 ms intervals
Connection type 1-wire connections
Input resistance Channels 1 to 6, high-speed inputs: 7.5 kΩ
Channels 7 to 16, standard inputs: 10 kΩ
Channels 17 to 32, mixed channels: 10 kΩ
Additional functions Channels 1 to 6, high-speed digital inputs:
2x 40 kHz event counting, 2x ABR incremental encoder, 2x period measurement, 2x gate time measurement, 2x counter latch function
Switching threshold
Low <5 VDC
High >15 VDC
Insulation voltage between channel and bus 1210 VDC
ABR incremental encoder
Quantity 2
Encoder inputs 24 V, asymmetrical
Counter size 16-bit
Input frequency 40 kHz
Evaluation 4x
Event counters
Quantity 2
Signal form Square wave pulse
Evaluation Rising edge, falling edge or both edges
The counter is cyclical.
Input frequency 40 kHz
Counter size 16-bit
Edge detection / Time measurement
Possible measurements Period measurement, gate time measurement
Signal form Square wave pulse
Evaluation Positive edge - Negative edge
Counter size 16-bit
Counter frequency
Internal 48 MHz, 24 MHz, 12 MHz, 6 MHz, 3 MHz, 1.5 MHz, 750 kHz, 375 kHz, 187.5 kHz
Length of pause between pulses ≥100 μs
Pulse length ≥20 μs
Digital outputs
Quantity 13 standard outputs, 3 high-speed outputs
All outputs designed as mixed channels, configurable as inputs or outputs using software
Variant Current-sourcing FET
Nominal voltage 24 VDC
Switching voltage 24 VDC -15% / +20%
Nominal output current 0.5 A per channel
DO 22 and DO 30: Optional 0.5 or 2 A starting with Rev. B1
Total nominal current 8 A
Connection type 1-wire connections
Output circuit Source
Output protection Thermal shutdown in the event of overcurrent or short circuit (see value "Short-circuit peak current")
Pulse width modulation
Period duration 1 to 65 ms
Pulse duration 0 to 100%
Resolution for pulse duration 0.1%
Diagnostic status Output monitoring with 25 ms delay
Leakage current when the output is switched off 3 µA
RDS(on) 78 mΩ
Peak short-circuit current 6.95 A
Switch-on in the event of overload shutdown or short-circuit shutdown Approx. 3 ms (depends on the module temperature)
Switching delay
0 → 1 ≤300 μs
1 → 0 ≤300 μs
Switching frequency
Resistive load Standard outputs: Max. 500 Hz
High-speed outputs: Max. 1 kHz
Braking voltage when switching off inductive loads Typ. 53 VDC
Insulation voltage between channel and bus 1210 VDC
Electrical properties
Electrical isolation Channel isolated from bus
Channel not isolated from channel
Operating conditions
Mounting orientation
Horizontal Yes
Vertical Yes
Installation elevation above sea level
0 to 2000 m No limitation
>2000 m Reduction of ambient temperature by 0.6°C per 100 m
Maximum 4000 m
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Horizontal mounting orientation -25 to 60°C
Vertical mounting orientation -25 to 45°C
Derating See section "Derating".
Storage -40 to 85°C
Transport -40 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Mechanical properties
Note Order terminal blocks separately (see section "Order data").
Dimensions
Width (pitch) 27.5+0.2 mm
Height 124 mm
Depth 92 mm
型番:
X20DMF320
説明:
  • 16 digital inputs
  • Sink circuit
  • 2 counter inputs with 40 kHz counter frequency
  • ABR incremental encoder
  • Period duration / gate time measurement
  • 16 mixed channels optionally as input or output
  • Source circuit
  • Integrated output protection
  • 3 PWM outputs
  • All channels with 1-wire connections

The module is equipped with 16 inputs and 16 mixed channels, optionally as input or output in 1-wire technology. The outputs are designed for a source output circuit, and the inputs are designed for a sink circuit.

必須アクセサリ
Terminal blocks
X20TBS1 Terminal block set for X20 I/O module: 2x 16-pin terminal block
X20TBS2 Terminal block set for X20 I/O module: 8x 4-pin terminal block
Automation Studio HW アップグレード バージョン (日付) ダウンロード
V4.0 HW Upgrade (X20DMF320) EXE / 1 MB
V6.0 HW Upgrade (X20DMF320) EXE / 1 MB
E-CAD（ElectroまたはEPLANテンプレート） バージョン (日付) ダウンロード
Makro-/Artikeldaten 4.0.5 (X20DMF320) EXE / 2 MB
M-CAD (Mechan.Templates) バージョン (日付) ダウンロード
3D files DXF/STEP X20DMF320 ZIP / 2 MB
ドキュメンテーション バージョン (日付) ダウンロード
Data sheet X20DMF320 PDF / 2 MB
X20 System User´s Manual PDF / 49 MB
証明書 バージョン (日付) ダウンロード
E115267 UL Certificate of Compliance X20 PDF / 2 MB
EU Data Act - X20 IO - Connected Product Information Notice PDF / 92 KB
EU Declaration of conformity PLC X20 PDF / 169 KB
UK Declaration PLC X20 PDF / 151 KB

国と言語を選ぶ

B&R Logo