DWL@DWL10000777849
| Version | Sprog | Operativ system | Dato | Størrelse | Type | Download |
|---|---|---|---|---|---|---|
| 3.0.0.0 | * | 25/07/2025 | 980 KB | EXE | AS6_HW_X67SI8103.exe | |
| Beskrivelse |
V6.0 HW Upgrade (X67SI8103) Revision information X67SI8103 Version 3.0.0.0: ID: FUVI-11178 Control of the outputs reworked Control of the outputs reworked Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: FUVI-11177 New data sheet V3.0.0 New data sheet V3.0.0 Channel description changed: No Configuration description changed: No Firmware changed: No ID: FUVI-11176 First official release for Safety+ First official release for Safety+ Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\42918_1.fw(650) Version 2.6.1.0: ID: FUVI-10596 Newdata sheet V2.21 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: FUVI-10595 Sensor supply for X67 modules The pulse outputs can be configured to supply voltage for field mounted sensors. Channel description changed: No Configurationdescription changed: No Firmware changed: Yes ID: QCAS-240 Test pulse generation and evaluation process corrected The time sequencefor test pulse generation and evaluation has been revised.Channels are acknowledged simultaneously after a short circuit, there is no discrepancy error. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 10\42918_1.fw(581) Version 2.6.0.0: ID: 780165 Correction of the input filter with set "Filter off". Correction of the input filter, if a "Filter off" is set and a channel error is detected. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 780270 New data sheet V2.18 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration descriptionchanged: No Firmware changed: No Firmware: 10\42918_1.fw(580) Version 2.2.0.0: ID: 668620 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688770 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689720 Propagation delay statistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689905 Increased delay of external feedback error detection Increased delay of external feedback error detection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689955 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690010 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690100 New data sheet V2.06 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\42918_1.fw(571) Version 2.1.0.0: ID: 644285 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\42918_1.fw(570) Version 1.10.9.1: ID: 643220 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.0: ID: 618290 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a loggerentry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configurationdescription changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC ofthe Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentryon negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 Diagnostic coverage not relevant for users Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleIDgreater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414030 Channel-Status-Info ON The default value of theChannel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "Disable OSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration descriptionchanged: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosen PLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 414370 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmwarechanged: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281),4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The modulealso supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in descriptionfile changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
| Version | Sprog | Operativ system | Dato | Størrelse | Type | Download |
| 2.6.1.0 | * | 04/03/2025 | 2 MB | EXE | AS6_HW_X67SI8103.exe | |
| Beskrivelse |
V6.0 HW Upgrade (X67SI8103) Revision information X67SI8103 Version 2.6.1.0: ID: FUVI-10596 New data sheet V2.21 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: FUVI-10595 Sensor supply for X67 modules The pulse outputs can be configured to supply voltage for field mounted sensors. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: QCAS-240 Test pulse generation and evaluation process corrected The time sequence for test pulse generation and evaluation has been revised. Channels are acknowledged simultaneously after a short circuit, there is no discrepancy error. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 10\47996_1.fw(581) Version 2.6.0.0: ID: 780170 Correction of the input filter with set "Filter off". Correction of the input filter, if a "Filter off" is set and a channel error is detected. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 780275 New data sheet V2.18 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(580) Version 2.4.0.0: ID: 715280 Failsafe at every boot It could happen under rare conditions that the module is stuck in failsafe state at every boot, generating logger messages: -1073565951/-1073561855 "internal cross communication error EPS" or -1073565945/-1073561849 "Received crc data is not equal to sent crc data" Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 727155 New data sheet V2.10 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(574) Version 2.3.1.0: ID: 706365 Limit values for the module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 706405 New data sheet V2.08 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(573) Version 2.2.0.0: ID: 668625 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688775 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longerthan the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689725 Propagation delay statistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689960 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration descriptionchanged: No Firmware changed: Yes ID: 690110 New data sheet V2.06 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(571) Version 2.1.0.0: ID: 644315 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmwarechanged: Yes Firmware: 10\47996_1.fw(570) Version 1.10.10.0: ID: 622805 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(331) Version 1.10.9.1: ID: 643225 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 6\47996_1.fw(301), 7\47996_1.fw(330) Version 1.10.9.0: ID: 460730 functional outputs deaktivated at powerup The functional outputs are deactivated on while powerup of module now. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 618295 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(330) Version 1.10.1.1: ID: 559200 minimum allowed operating temperature extended to -40°C The minimum allowed operating temperature was extended to -40°C Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(326) Version 1.10.1.0: ID: 516625 minimum allowed operating temperature extended to-40°C The minimum allowed operating temperature was extended to -40°C Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 533060 Add blackout mode Addblackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533150 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 541340 New default values The default valuesfor "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 550705 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 550745 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed:Yes Configuration description changed: No Firmware changed: Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(325) Version 1.10.0.1: ID: 487615 Possibility to configure the outputs to be switched in SafeDESIGNER Starting with SafetyRelease 1.10 the outputs can be configuredto be switched in SafeDESIGNER instead of Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 6\47996_1.fw(301), 7\47996_1.fw(320) Version 1.10.0.0: ID: 385305 keine Channel description changed: No Configuration description changed: No Firmware changed: No ID: 402845 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470675 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470680 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization oftiming parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 6\47996_1.fw(301), 7\47996_1.fw(320) Version 1.9.1.0: ID: 424655 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424660 fw valid from SafetyRelease 1.2 on The firmware is used for all SafetyReleases from 1.2 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 424665 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 6\47996_1.fw(301) Version 1.9.0.0: ID: 413880 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414035 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414375 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration descriptionchanged: No Firmware changed: No Firmware: 3\47996_1.fw(290), 4\47996_1.fw(300) Version 1.6.0.8: ID: 388480 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.6.0.7: ID: 339305 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.6.0.5: ID: 335525 unlock of SafeModuleIDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335530 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.6.0.0: ID: 314370 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.5.0.4: ID: 303420 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed:No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.5.0.1: ID: 294350 First Official Release First Official Release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) |
|||||
| Version | Sprog | Operativ system | Dato | Størrelse | Type | Download |
| 2.6.0.0 | * | 05/03/2024 | 2 MB | EXE | AS6_HW_X67SI8103.exe | |
| Beskrivelse |
V6.0 HW Upgrade (X67SI8103) Revision information X67SI8103 Version 2.6.0.0: ID: 780170 Correction of the input filter with set "Filter off". Correction of the input filter, if a "Filter off" is set and a channel error is detected. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 780275 New data sheet V2.18 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(580) Version 2.4.0.0: ID: 715280 Failsafe at every boot It could happen under rare conditions that the module is stuck in failsafe state at every boot, generating logger messages: -1073565951/-1073561855 "internal cross communication error EPS" or -1073565945/-1073561849 "Received crc data is not equal to sent crc data" Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 727155 New data sheet V2.10 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(574) Version 2.3.1.0: ID: 706365 Limit values for the module cycle time adjusted The limit values for the calculation and monitoringof module cycle time andslot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 706405 New data sheet V2.08 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(573) Version 2.2.0.0: ID: 668625 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688775 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689725 Propagation delay statistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689960 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690110 New data sheet V2.06 Forchanges see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\47996_1.fw(571) Version 2.1.0.0: ID:644315 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - seechapter "Switching to mapp Safety" in help! Channel description changed:Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\47996_1.fw(570) Version 1.10.10.0: ID: 622805 Sporadic errors 114982, 102914, 120065, 110385 Sporadic errors 114982, 102914, 120065, 110385 have been fixed Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(331) Version 1.10.9.1: ID: 643225 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 6\47996_1.fw(301), 7\47996_1.fw(330) Version 1.10.9.0: ID: 460730 / Support ID: 400173996, 400196973,400253218 functional outputs deaktivated at powerup The functional outputs are deactivated on while powerup of module now. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 618295 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(330) Version 1.10.1.1: ID: 559200 minimum allowed operating temperature extended to -40°C The minimum allowed operating temperature was extended to -40°C Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(326) Version 1.10.1.0: ID: 516625 minimum allowed operating temperature extended to -40°C The minimum allowed operating temperature was extended to -40°C Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 533060 Add blackout mode Add blackout mode Channel description changed:Yes Configuration description changed: No Firmware changed: No ID: 533150 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 541340 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration descriptionchanged: Yes Firmware changed: No ID: 550705 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 550745 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 6\47996_1.fw(301), 7\47996_1.fw(325) Version 1.10.0.1: ID: 487615 / Support ID: 400191602 Possibility to configure the outputs to be switched in SafeDESIGNER Startingwith SafetyRelease 1.10 the outputs can be configured to be switched in SafeDESIGNER instead of Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 6\47996_1.fw(301), 7\47996_1.fw(320) Version 1.10.0.0: ID: 385305 / Support ID: 400135300 keine Channel description changed: No Configuration description changed: No Firmware changed: No ID: 402845 / Support ID: 400142613 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470675 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470680 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 6\47996_1.fw(301), 7\47996_1.fw(320) Version 1.9.1.0: ID: 424655 change of input filter The behaviour of the input filterhas changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 424660 fw valid from SafetyRelease 1.2 on The firmware is used for all SafetyReleases from1.2 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 424665 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 6\47996_1.fw(301) Version 1.9.0.0: ID: 413880 SafeModuleID>300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414035 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414375 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290), 4\47996_1.fw(300) Version 1.6.0.8: ID: 388480 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.6.0.7: ID: 339305 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.6.0.5: ID: 335525 /Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDsup to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335530 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed:No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.6.0.0: ID: 314370 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.5.0.4: ID: 303420 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) Version 1.5.0.1: ID: 294350 First Official Release First Official Release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 3\47996_1.fw(290) |
|||||
