DWL@DWL10000017817
| Version | Sprog | Operativ system | Dato | Størrelse | Type | Download |
|---|---|---|---|---|---|---|
| 1.16 | * | DOS | 17/07/2006 | 392 KB | ZIP | MP100_200_BIOS_Upgrade_V1_16.zip |
| Beskrivelse |
BIOS Upgrade BIOS Upgrade for Mobile Panel 100 BIOS devices. **************************************************************** WARNING Do not abort a running BIOS upgrade! Otherwise the Mobile Panel cannot be rebooted afterwards and must be sent to B&R for repair. Retry the aborted upgrade process WITHOUT rebooting the Mobile Panel, for example by directly calling batch file UPDBIOS.BAT. **************************************************************** ****************************************************************After a BIOS upgrade the BIOS uses automatically the CMOS default settings. If you have changed settings in the CMOS Setup you must change these settings again after upgrade! Therefore write down your settings before upgrading. **************************************************************** 1. Copy all files to a bootable disk. *************************************************************** WARNING The boot disk should be created with DOS, Windows ME or XP. With Windows 98 boot disks errors may occur when upgrading the BIOS - the Mobile Panel cannot boot after the upgrade then! *************************************************************** Note: You can use a bootable Compact Flash card instead of a disk also. 2. Insert the disk in a (USB) floppy drive connected to the Mobile Panel and re-boot the device. Note: You can use the floppy drive of a remote PC via the Power Panel / Mobile Panel Remote Host (short: REMHOST) Utility The REMHOST utility is available as separate download from B&R. 3. A boot menu with following options is shown after booting: 1. Upgrade complete System All BIOS areas (XpressROM and FPGA firmware) will be updated automatically (default after 5 sec). 2. Upgrade XpressROM BIOS Only the XpressROM BIOS will be updated automatically. 3. Upgrade FPGA Firmware Only both FPGA firmware will be updated automatically. 4. Save complete System All BIOS areas (XpressROM and FPGA Firmware) will be automatically saved. *********************************************************** There must be up to 640 kbytes free space left on the disk. *********************************************************** 5. Save XpressROM BIOS Only the XpressROM BIOS will be saved automatically. *********************************************************** There must be about 256 kbytes free space left on the disk. *********************************************************** 6. Save FPGA Firmware Only both FPGA firmware will be saved automatically. *********************************************************** There must be up to 384 kbytes free space left on the disk. *********************************************************** 7. Exit Exit to the Shell (MS-DOS). 4. Select the desired action. 5. Remove disk and reboot system after successful upgrade. Contents 6504_1.fp 0.1 NEW 6506_1.pci 0.8 NEW Autoexec.bat ChkWin98.exe 1.00 Choice.exe 1.00 Config.sys NEW Liesmich.txt NEW Readme.txt NEW SavBIOS.bat NEW SavFpga.bat NEW UpdBIOS.bat NEW UpdFpga.bat Xflash.exe 1.09 NEW Xpress.rom 1.16 NEW XpressQ.rom 1.16 NEW Fixes - Boot time with a Silicon Systems CF card ("SiliconDrive") was 5 to 6 seconds longer than with a SanDisk CF card. - A&P 89520: The system was rebooted when a key was pressed on the USB keyboard during boot from USB floppy between summary screen and boot message. - QVGA BIOS version only: register contents were maybe destroyed at display of the CF Card info in the BIOS setup. Changes - BIOS setup, Device Information menu: Text "CPU Intern" changed to "CPU Internal". - Wait time increased from 200 ms to 400 ms at TFT power on to avoid stripes on cHMI SVGA display. This int 10h patch has also an effect when switching the video mode in Windows XP. - BIOS and FPGA firmware files are saved into SAVED folder. - Check of BIOS file at BIOS update was improved. - RDFPRES.EXE was removed. The QVGA detection is done by XFLASH.EXE now. - File 6504_1.STN replaced by 6504_1.FP. - The display timings from the factory settings are used at resolution setting "Auto", if bit 3 of the display type in the Factory Settings is set to 1. The TFT Power Sequence Delay from the factory settings is read with factory settings version 5 or higher. - Flat Panel resolution "Auto (+ Timing)" added in BIOS Setup: like "Auto" but display timings are read always from factory settings instead of BIOS internal tables. Remark: resolution "Auto (+ Timing)" will be reset to "Auto" at BIOS update or Load Optimized Defaults -> maybe wrong timings are used then! - If the display timings from the factory settings cannot be set - for instance if a timing value cannot be converted for representation as SoftVGA register - the internal display timings are used. |
|||||
| Version | Sprog | Operativ system | Dato | Størrelse | Type | Download |
| 1.12 | * | DOS | 03/05/2005 | 401 KB | ZIP | MPx00_BIOS_Upgrade_V1_12.zip |
| Beskrivelse |
BIOS Upgrade BIOS Upgrade for Mobile Panel 100 BIOS devices. Contents 6504_1.stn 1.1 6506_1.pci 0.7 NEW Autoexec.bat NEW ChkWin98.exe 1.00 Choice.exe 1.00 Config.sys NEW Liesmich.txt NEW Rdfpres.exe 1.00 Readme.txt NEW SavBIOS.bat SavFpga.bat UpdBIOS.bat UpdFpga.bat Xflash.exe 1.08 Xpress.rom 1.12 NEW XpressQ.rom 1.12 NEW Fixes - The real time clock was set to the build date of the BIOS after reboot of the Mobile Panel, when a date with sunday has been set before under Windows. Changes - REMHOST moved to separate disk. |
|||||
| Version | Sprog | Operativ system | Dato | Størrelse | Type | Download |
| 1.11 | * | DOS | 18/01/2005 | 498 KB | ZIP | Mobile_Panel_100_BIOS_Upgrade_V01_11.zip |
| Beskrivelse |
BIOS Upgrade BIOS Upgrade for Mobile Panel 100 BIOS devices (5MP181.0843-07). Fixes - Last pixel line on VGA displays was missing. - XFLASH option -t=FPGA, FPG1, FPG2, PCI1 or PCI2 was rejected with error "not supported on this platform". Changes - Boot of on-board FPGAs is supported now. - Firmware file 6506_1.pci for on-board FPGA added. - Firmware file 6504_1.stn for on-board FPGA1 added. - MMX Instructions enabled. - PCI Slave Disconnect Boundary set to 128 bytes. - Speaker enabled. A beep occurs now at input errors in Setup. - Switching the video mode with INT 10h, AH=00h improved. - BIOS interrupt INT 15h, AX=E820h returns now the size of the Flash Memory correct with 2M instead of 256k only. - Memory timing adapted for Swissbit memory modules. - The User Serial ID can be read from the extended CMOS now. |
|||||
