Short description
Hub 1 Fast Ethernet interface for single-mode fiber optic cables for hub expansion
General information
Status indicators Module status, bus function
Diagnostics
Module status Yes, using LED status indicator
Bus function Yes, using LED status indicator
Power consumption 1.65 W
Additional power dissipation caused by actuators (resistive) [W] -
Certifications
CE Yes
UKCA Yes
ATEX Zone 2, II 3G Ex nA nC IIA T5 Gc
IP20, Ta (see X20 user's manual)
FTZÚ 09 ATEX 0083X
UL cULus E115267
Industrial control equipment
DNV Temperature: B (0 - 55°C)
Humidity: B (up to 100%)
Vibration: B (4 g)
EMC: B (bridge and open deck)
LR ENV1
ABS Yes
BV EC33B
Temperature: 5 - 55°C
Vibration: 4 g
EMC: Bridge and open deck
EAC Yes
Interfaces
Type Hub expansion module
Variant 1x female duplex LC
Transfer rate 100 Mbit/s
Transfer
Physical layer 100BASE-FX
Half-duplex Yes
Full-duplex No
Autonegotiation No
Auto-MDI/MDIX No
Hub propagation delay 0.96 to 1 µs
Wave length
Typ. 1300 nm

Rx range: 1270 to 1380 nm

Tx range: 1270 to 1380 nm
Cable fiber type Single-mode fiber with 9/125 µm core diameter
On both sides: Male duplex LC connector
Optical power budget 30 dB
Line length
Half-duplex Max. 175 m between 2 stations (segment length)
POWERLINK Max. 50 km between 2 stations (segment length)
Electrical properties
Electrical isolation Power supply isolated from Ethernet
Operating conditions
Mounting orientation
Horizontal Yes
Vertical Yes
Installation elevation above sea level
0 to 2000 m No limitation
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Horizontal mounting orientation -25 to 55°C
Vertical mounting orientation -25 to 45°C
Derating -
Storage -40 to 85°C
Transport -40 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Mechanical properties
Slot Hub expansion for X20BC8083, X20BC8084 and X20HB8880
Número de material:
X20HB1882
Descripción:
  • Hub expansion module
  • 1-port hub, 100BASE-FX
  • Single-mode glass fiber cables
  • Range up to 50 km
  • Hot-swappable

POWERLINK bus controllers X20BC8083 and X20BC8084 (revision D0 and later) and standalone hub X20HB8880 are equipped with a modular hub expansion. An additional 1 or  2 slots are available depending on the bus base being used. Hub expansion module X20HB1882 can be operated in these slots. Note that the hardware revision of the X20BC8083 and X20HB8880 must be ≥F0.

The hub expansion module is designed as a 1-port hub. The Ethernet connection is made using 9/125 µm single-mode glass fiber cables with a duplex LC connector. The module state and network status are indicated using LEDs.

Actualizaciones de hardware de Automation Studio Versión (fecha) Descargar
V4.0 HW Upgrade (X20HB1882) EXE / 666 KB
Certificados Versión (fecha) Descargar
ABS Certificate of Product Design Assessment - X20 IO Series PDF / 2 MB
BV Type Approval Certificate - X20 PDF / 556 KB
DNV Type Approval Certificate - X20 PDF / 194 KB
E115267 UL CoC X20 PDF / 1 MB
EU Declaration ATEX X20 PDF / 218 KB
EU Declaration of conformity PLC X20 PDF / 169 KB
Lloyds Register PDF / 502 KB
RINA Type Approval Certificate - X20 / Power Panel T30 PDF / 1 MB
UK Declaration PLC X20 PDF / 151 KB
Documentación Versión (fecha) Descargar
Data sheet X20HB1882 PDF / 181 KB
Installation- / EMC-Guide PDF / 20 MB
X20 System User´s Manual PDF / 7 MB
E-CAD (plantillas Electro o EPLAN) Versión (fecha) Descargar
X20 EPLAN P8 from V2.4 EXE / 160 MB

Seleccione país e idioma

B&R Logo