Short description
I/O module | 35 digital inputs, 6 analog inputs, 45 digital outputs, 4 analog outputs, 8 thermocouples, 2 PWM outputs |
Interfaces | 2x Ethernet, 1x CAN bus, 1x RS485 interface, 1x USB |
General information
B&R ID code | 0xF733 |
System requirements | |
Automation Studio | 4.5.01 or later |
Automation Runtime | B4.53 or later |
Cooling | Passive |
LEDs | |
Quantity | 7 |
Status | Supply voltage OK, operating state, module status, Ethernet, CAN, RS485 |
Power button | No |
Reset button | Yes |
Controller redundancy | |
Master capability | No |
Buzzer | No |
Support | |
ACOPOS support | No |
Visual Components support | No |
Safety support | No |
Electrical isolation |
Thermocouples, Ethernet 1 (IF2) and Ethernet 2 (IF3) isolated from each other and from other interfaces Power supply not isolated from channel, and channel not isolated from channel |
Certifications | |
CE | Yes |
Controller
Interfaces
Interface IF2 | |
Connection designation | X2 Ethernet1 |
Type | Ethernet |
Variant | 1x RJ45 shielded |
Line length | Max. 100 m between 2 nodes (segment length) |
Max. transfer rate | 10/100 Mbit/s |
Transfer | |
Physical layer | 10BASE-T/100BASE-TX |
Half-duplex | Yes |
Full-duplex | Yes |
Autonegotiation | Yes |
Auto-MDI/MDIX | Yes |
Interface IF3 | |
Connection designation | X3 Ethernet2 |
Type | Ethernet |
Variant | 1x RJ45 shielded |
Line length | Max. 100 m between 2 nodes (segment length) |
Max. transfer rate | 10/100 Mbit/s |
Transfer | |
Physical layer | 10BASE-T/100BASE-TX |
Half-duplex | Yes |
Full-duplex | Yes |
Autonegotiation | Yes |
Auto-MDI/MDIX | Yes |
Interface IF4 | |
Connection designation | X1 USB1 |
Type | USB 2.0 |
Variant | Type A |
Current-carrying capacity | 0.5 A |
Interface IF6 | |
Connection designation | X4 CAN1 |
Type | CAN bus |
Variant | Connection made using 0TB1110.9000 |
Transfer rate | Max. 1 Mbit/s |
Interface IF8 | |
Connection designation | X4 RS485 |
Type | RS485 |
Variant | Connection made using 0TB1110.9000 |
Transfer rate | Max. 115.2 kbit/s |
Digital inputs
Quantity | 33 inputs + 2 counter inputs |
Nominal voltage | 24 VDC |
Input voltage | 24 VDC ±20% |
Input current at 24 VDC | 3.2 mA |
Additional functions | Event counter, gate and period measurement |
Circuit | Sink or source |
Input delay |
Counter inputs 1 to 2: <4 µs Inputs 3 to 33: <1 ms |
Switching threshold | |
Low | <5 V |
High | >15 V |
Event counters
Quantity | 2 |
Signal form | Square wave pulse |
Evaluation | Positive or negative edge, cyclic counter |
Input frequency | Max. 100 kHz |
Pulse length | >4 µs |
Counter size | 16-bit |
Supported inputs |
Input 1: Counter 1 Input 2: Counter 2 |
Gate measurement
Period measurement
Analog inputs
Thermocouple temperature inputs
Digital outputs
PWM output
Analog outputs
Quantity | 4 |
Output | ±10 V |
Digital converter resolution | 12-bit |
Switch on/off behavior | Internal enable relay, for startup |
Max. error | |
Gain | 0.080%, based on the current output value |
Offset | 0.050%, based on the entire output range |
Output protection | Protection against wiring with supply voltage, short-circuit proof |
Output format | |
Data type | INT |
Voltage | INT 0x8000 - 0x7FFF / 1 LSB = 0x0010 = 4.88 mV |
Range of values | |
10 V | 0x7FFF |
0 V | 0x0000 |
-10 V | 0x8000 |
Max. load per output | ±10 mA (load ≥1 kΩ) |
Max. gain drift | 0.08%, based on the current output value |
Max. offset drift | 0.05%, based on the entire output range |
Error caused by load change | 0.015% from 10 MΩ → 1 kΩ, resistive |
Nonlinearity | 0.025%, based on the output range |
Power supply unit
Voltage range | 24 VDC ±25% |
Power consumption | 3.5 W |
Voltage monitoring | Yes |
Operating conditions
Mounting orientation | |
Horizontal | No |
Vertical | Yes |
Pollution degree per EN 60664-1 | 2 |
Ambient conditions
Temperature | |
Operation | 0 to 50°C |
Storage | -40 to 85°C |
Transport | -40 to 85°C |
Relative humidity | |
Operation | 10 to 90%, non-condensing |
Storage | 5 to 95%, non-condensing |
Transport | 5 to 95%, non-condensing |
Mechanical properties
Dimensions | |
Width | 190 mm |
Height | 198 mm |
Depth | 31 mm |
Module dimensions including mounting plates | 190 x 198 x 31 mm (W x H x D) |
Número de material:
XEPIMC100.02Descripción:
CPU I/O board, ARM Cortex-A9, 667 MHz, 2 GB flash memory, 512 MB DDR3 SDRAM, 64 kB FRAM, 24 VDC, 2x Ethernet interface,1x CAN bus, 1x RS485 interface, 1x USB 2.0 interface, 35 digital inputs, 24 VDC, sink/source, 2 event counters or gate time / period measurement, 33 digital outputs, 24 VDC, 2 A (50%), 12 digital outputs, 24 VDC, 0.5 A, 2 PWM outputs, 3 A, 8 thermocouple inputs J, K, S, N, 4 analog inputs for potentiometers, 0 to 10 V, 0 to 20 mA, 4.5 V, 14-bit, 2 analog inputs ±10 V, 14-bit, 4 analog outputs, ±10 V, 12-bit
Accesorios obligatorios
Accesorios opcionales
Other
XEPIMA100.01 | SMARTMOLD I/O connector set (100 I/Os) cage clamp terminals |
XEPIMA200.01 | SMARTMOLD I/O connector set (119 I/Os) cage clamp terminals |
Actualizaciones de hardware de Automation Studio | Versión (fecha) | Descargar |
---|---|---|
V4.5 HW Upgrade (XEPIMC100.02) | EXE / 8 MB |