DWL@DWL10000101538
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
|---|---|---|---|---|---|---|
| 1.1.4.0 | * | 17/12/2013 | 4 MB | EXE | AS3.0_HW_X20CP1483-1.exe | |
| Description |
V3.0 HW Upgrade (X20CP1483-1) Revision information X20CP1483-1 Version 1.1.4.0: ID: 358970 POWERLINK MN mode: If "Multiplexing prescale" >= 9, then the input data of the multiplexed stations that were configured in the last "network cycle" were not transferred in certain configurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\44741_0.pci(43), 1\44741a0.epl(64) Version 1.1.3.0: ID: 332320 / Support ID: 400092134 POWERLINK V1: If the "Activate Ethernet communication off" option is enabled, asynchronous POWERLINK communication fails in some circumstances. The following configuration may cause asynchronous communication to fail: - POWERLINK V1 - "Activate Ethernet communication off" - POWERLINK CNs on the network that also support POWERLINK V2 This upgrade can beinstalled to resolve this problem. It is also possible to set "Activate Ethernet communication" to "On". Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 337360 /Support ID: 400108118 POWERLINK V2 CN mode It was possible that an undefined state occurred during booting that causedthe interface to fail. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\44741_0.pci(43), 1\44741a0.epl(63) Version 1.1.2.0: ID: 296090 Compatibility to Atom CPU Allows the replacement of a X20CPx48x through X20CPx58x in an existing AS configuration. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\44741_0.pci(43), 1\44741a0.epl(60) Version 1.1.1.0: ID: 285850 POWERLINK V2 CN mode: Asynchronous packets lost when there is a large asynchronous load with large asynchronous frames. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 286040 POWERLINK V2: Large fluctuations of IEEE 1588 Nettime (used for safety logbook entries) during startup. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\44741_0.pci(43), 1\44741a0.epl(60) Version 1.1.0.2: ID: 227235 Enhancement status datapoint for I/O supply Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 256720 / Support ID: 400057319 POWERLINK: In controlled nodemode, the I/O mapping was not applied when themanager was restarted. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 256855 POWERLINK: LinkOK data point added. Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 257000 POWERLINK: Support for 100 Mbit full duplex in Ethernet operating mode. Channel description changed: No Configuration description changed: Yes Firmware changed:Yes ID: 265710 POWERLINK V2 CN mode: Frequent MN failures result in CPU going into Servicemode. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 265810 Warning 32168 "POWERLINK V2: Invalid frame format" on iCN with "Chaned Station" on the same network Error correction: When an iCN is used in the same POWERLINK network with a "Chained Station", there may be warnings 32168 in the logger. The reason for this warning is that the sync response frames that are used to measure the timing of the "Chained Station" are not recognized by the iCN. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\44741_0.pci(43), 1\44741a0.epl(58) Version 1.0.16.0: ID: 240375 FPGA Fitter upgrade Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\44741_0.pci(42), 1\44741a0.epl(52) Version 1.0.15.0: ID: 230780 POWERLINK V2 CN mode: Frequent MN failures result in CPU going into Servicemode. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\44741_0.pci(40), 1\44741a0.epl(52) Version 1.0.14.0: ID: 220470 POWERLINK V2: Boot behavior improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\44741_0.pci(40), 1\44741a0.epl(51) Version 1.0.0.0: ID: 212620 Support of X20CP1483-1 Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\44741_0.pci(40), 1\44741a0.epl(47) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 1.0.0.0 | * | 07/10/2009 | 583 KB | EXE | AS3.0_HW_X20CP1483-1.exe | |
| Description |
V3.0 HW Upgrade (X20CP1483-1) Revision information X20CP1483-1: Version 1.0.0.0: ID#212620: Support of X20CP1483-1 Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes |
|||||
