DWL@DWL10000604599
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
|---|---|---|---|---|---|---|
| 2.6.0.0 | * | 05/03/2024 | 2 Mo | EXE | AS4_HW_X20SC0402.exe | |
| Description |
V4.6 HW Upgrade (X20SC0402) Revision information X20SC0402 Version 2.6.0.0: ID: 780135 Correction of the input filter with set "Filter off". Correction of the input filter, if a "Filter off" is set and a channel error is detected. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 780225 New data sheet V2.20 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 780380 / Support ID: 400412437 Configuration for Power Calculation available The Configuration for Power Calculation is now available in Automation Studio Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 10\59384_1.fw(580) Version 2.4.0.0: ID: 715230 Failsafe at every boot It could happen under rare conditions that the module is stuck in failsafe state at every boot, generating logger messages: -1073565951/-1073561855 "internal cross communication error EPS" or -1073565945/-1073561849 "Received crc data is not equal to sent crc data" Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 720345 New data sheet V2.10 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 726315 The power calculation of the modules is supported The data for the power calculation of the data sheet isincluded in the HWX. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(574) Version 2.3.1.0: ID: 703240 New data sheet V2.08 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 706310 Limit values for the module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 10\59384_1.fw(573) Version 2.3.0.0: ID: 692340 Support of the DYNlink interface The DYNlink interface is supported by the safe inputs. Channel description changed: No Configuration description changed: Yes Firmware changed: Yes ID: 692380 / Support ID: 400311305 The OSDD signal at the pulse output is corrected. The OSDD signal atthe pulse output is output correctly even when not in use. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 696550 New data sheet V2.07 For changes see chapter "Version history" in the data sheet. Channel description changed:No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(572) Version 2.2.0.1: ID: 668540 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID:688710 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689695 Propagation delay statistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689890 Increased delay of external feedback error detection Increased delay of external feedback error detection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689925 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689995 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis ofthe output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690070 New data sheet V2.06 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(571) Version 2.1.0.0: ID: 568710 Acknowledge several Channel errors with one ReleaseOutput edge. Several channel error of different types(HSHS, HSLS) areacknowledged with only one ReleaseOutput edge. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 596890 / Support ID: 400253825 cleared statement in help about open circuit detection cleared statement in help that the module has noopen circuit detection Channel description changed: No Configuration description changed: No Firmware changed: No ID: 644155 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\59384_1.fw(570) Version 1.10.9.1: ID: 643135 data sheetV1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(330) Version 1.10.9.0: ID: 618210 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(330) Version 1.10.1.0: ID: 516610 / Support ID: 400203957 add PhysicalStateChannels on X20SLX842 add PhysicalStateChannels on X20SLX842. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 539150 Adaptfilter algorithm to eliminate dependencies between TON and TOF-filter Filter algorithm was adapted to eliminate dependencies between TON and TOF-filter which existed since FW V301. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 541650 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549925 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 570155 Increase the tolerance of the voltage monitor The tolerance of the voltage monitor was increased to prevent sporadic false errors 99849 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(325) Version 1.10.0.6: ID: 532880 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532885 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532890 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\59384_1.fw(322) Version 1.10.0.3: ID: 473000 Improved stability The stability of the module was improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(322) Version 1.10.0.2: ID: 473375 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(320) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.4.0.0 | * | 09/06/2021 | 2 Mo | EXE | AS4_HW_X20SC0402.exe | |
| Description |
V4.6 HW Upgrade (X20SC0402) Revision information X20SC0402 Version 2.4.0.0: ID: 715230 Failsafe at every boot It could happen under rare conditions that the module is stuck in failsafe state at every boot, generating logger messages: -1073565951/-1073561855 "internal cross communication error EPS" or -1073565945/-1073561849 "Received crc data is not equal to sent crc data" Channel description changed: No Configurationdescription changed: No Firmware changed: Yes ID: 720345 New data sheet V2.10 For changes see chapter "Version history" in the datasheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 726315 The power calculation of the modules is supported The data for the power calculation of the data sheet is included in the HWX. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(574) Version 2.3.1.0: ID: 703240 New datasheet V2.08 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 706310 Limit values for the module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 10\59384_1.fw(573) Version 2.3.0.0: ID: 692340 Support of the DYNlink interface The DYNlink interface is supported by the safe inputs. Channel description changed: No Configuration description changed: Yes Firmware changed: Yes ID: 692380 / SupportID: 400311305 The OSDD signal at the pulse output is corrected. TheOSDD signal at the pulse output is output correctly even when not in use. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 696550 New data sheet V2.07 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(572) Version 2.2.0.1: ID: 668540 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688710 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689695 Propagation delay statistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689890 Increased delay of external feedback error detection Increased delay of external feedback error detection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689925 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689995 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690070 New data sheet V2.06 For changes see chapter "Version history" in thedata sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(571) Version 2.1.0.0: ID: 568710 Acknowledge several Channel errors with one ReleaseOutput edge. Several channel error of different types(HSHS, HSLS) are acknowledged with only one ReleaseOutput edge. Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 596890 / Support ID: 400253825 cleared statement in help about open circuit detection cleared statement in help that the module has no open circuit detection Channel description changed: No Configuration description changed: No Firmware changed: No ID: 644155 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\59384_1.fw(570) Version 1.10.9.1: ID: 643135 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(330) Version 1.10.9.0: ID: 618210 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(330) Version 1.10.1.0: ID: 516610 / Support ID: 400203957 add PhysicalStateChannels on X20SLX842 add PhysicalStateChannels on X20SLX842. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 539150 Adapt filter algorithm to eliminate dependencies between TON and TOF-filter Filter algorithm was adapted to eliminate dependencies between TON and TOF-filter which existed since FW V301. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 541650 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed:No Configuration description changed: Yes Firmware changed: No ID: 549925 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 570155 Increase the tolerance of the voltage monitor The tolerance of the voltage monitor was increased to prevent sporadic false errors 99849 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(325) Version 1.10.0.6: ID: 532880 Addblackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532885 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532890 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\59384_1.fw(322) Version 1.10.0.3: ID: 473000 Improved stability The stability of the module was improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(322) Version 1.10.0.2: ID: 473375 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(320) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.3.1.0 | * | 01/12/2020 | 2 Mo | EXE | AS4_HW_X20SC0402.exe | |
| Description |
V4.6 HW Upgrade (X20SC0402) Revision information X20SC0402 Version 2.3.1.0: ID: 703240 New data sheet V2.08 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 706310 Limit values for the module cycle time adjusted Thelimit values for the calculation and monitoring of module cycle time andslottime adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 10\59384_1.fw(573) Version 2.3.0.0: ID: 692340 Support of the DYNlink interface The DYNlink interface is supported by the safe inputs. Channel description changed: No Configuration description changed: Yes Firmware changed: Yes ID: 692380 / Support ID: 400311305 The OSDD signal at the pulse output is corrected. The OSDD signal at the pulse outputis output correctly even when not in use. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 696550 New data sheet V2.07 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(572) Version 2.2.0.1: ID: 668540 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688710 / SupportID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689695 Propagation delaystatistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689890 Increased delay of external feedback error detection Increased delay of external feedback error detection Channel description changed: No Configuration description changed:No Firmware changed: Yes ID: 689925 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689995 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690070 New data sheet V2.06 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(571) Version 2.1.0.0: ID: 568710 Acknowledge several Channel errors with one ReleaseOutput edge. Several channel error of different types(HSHS, HSLS) are acknowledged with only one ReleaseOutput edge. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 596890 / Support ID: 400253825 cleared statement in help about open circuit detection cleared statement in help that the module has no open circuit detection Channel description changed: No Configuration description changed: No Firmware changed: No ID: 644155 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\59384_1.fw(570) Version 1.10.9.1: ID: 643135 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(330) Version 1.10.9.0: ID: 618210 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(330) Version 1.10.1.0: ID: 516610 / Support ID: 400203957 add PhysicalStateChannels on X20SLX842 add PhysicalStateChannels on X20SLX842. Channel description changed: Yes Configuration description changed:No Firmware changed: Yes ID: 539150 Adapt filter algorithmto eliminate dependencies between TON and TOF-filter Filter algorithm was adapted to eliminate dependencies between TON and TOF-filter which existed since FW V301. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 541650 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549925 Provide CRCof the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 570155 Increase the tolerance of the voltage monitor The tolerance of the voltage monitor was increased to prevent sporadic false errors 99849 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(325) Version 1.10.0.6: ID: 532880 Add blackout mode Add blackoutmode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532885 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532890 Update ECAD data Update ECAD data Channeldescription changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\59384_1.fw(322) Version 1.10.0.3: ID: 473000 Improved stability The stability of the module was improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(322) Version 1.10.0.2: ID: 473375 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(320) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.3.0.0 | * | 02/09/2020 | 2 Mo | EXE | AS4_HW_X20SC0402.exe | |
| Description |
V4.6 HW Upgrade (X20SC0402) Revision information X20SC0402 Version 2.3.0.0: ID: 692340 Support of the DYNlink interface The DYNlink interface is supported by the safe inputs. Channel description changed: No Configuration description changed: Yes Firmware changed:Yes ID: 692380 / Support ID: 400311305 The OSDD signal at the pulse output is corrected. The OSDD signal at the pulse output is output correctly even when not in use. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 696550 New data sheet V2.07 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(572) Version 2.2.0.1: ID: 668540 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688710 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689695 Propagation delay statistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689890 Increased delay of external feedback error detection Increased delay of external feedback error detection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689925 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689995 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690070 New data sheet V2.06 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 10\59384_1.fw(571) Version 2.1.0.0: ID: 568710 Acknowledge several Channel errors with one ReleaseOutput edge. Severalchannel error of different types(HSHS, HSLS) are acknowledged with only one ReleaseOutput edge. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 596890 / Support ID: 400253825 cleared statement in help about open circuit detection cleared statement in help that the module has no open circuit detection Channel description changed: No Configuration description changed: No Firmware changed: No ID: 644155 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existingapplications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\59384_1.fw(570) Version 1.10.9.1: ID: 643135 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(330) Version 1.10.9.0: ID: 618210 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(330) Version 1.10.1.0: ID: 516610 / Support ID: 400203957 add PhysicalStateChannels on X20SLX842 add PhysicalStateChannels on X20SLX842. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 539150 Adapt filter algorithm to eliminate dependencies between TON and TOF-filter Filter algorithm was adapted toeliminate dependencies between TON and TOF-filter which existed since FW V301. Channel description changed: No Configuration description changed:No Firmware changed: Yes ID: 541650 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549925 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID:570155 Increase the tolerance of the voltage monitor The tolerance of the voltage monitor was increased to prevent sporadic false errors 99849 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(325) Version 1.10.0.6: ID: 532880 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532885 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532890 Update ECAD data Update ECAD data Channel descriptionchanged: No Configuration description changed: Yes Firmware changed: No Firmware: 1\59384_1.fw(322) Version 1.10.0.3: ID: 473000 Improved stability The stability of the module was improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(322) Version 1.10.0.2: ID: 473375 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(320) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.2.0.1 | * | 21/07/2020 | 2 Mo | EXE | AS4_HW_X20SC0402.exe | |
| Description |
V4.6 HW Upgrade (X20SC0402) Revision information X20SC0402 Version 2.2.0.1: ID: 668540 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 688710 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689695 Propagation delay statistics The Propagation delay statistics can now be read out. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689890 Increased delay of external feedback error detection Increased delay of external feedback error detection Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689925 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 689995 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 690070 New data sheet V2.06 For changes see chapter "Version history" in the data sheet. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware:10\59384_1.fw(571) Version 2.1.0.0: ID: 568710 Acknowledge several Channel errors with one ReleaseOutput edge. Several channel error of different types(HSHS, HSLS) are acknowledged with only one ReleaseOutput edge. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 596890 / Support ID: 400253825 cleared statement in help about open circuit detection cleared statement in help that the module has no open circuit detection Channel description changed: No Configuration description changed: No Firmware changed: No ID: 644155 major (even incompatible) changes for mapp Safety First upgrade for mapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\59384_1.fw(570) Version 1.10.9.1: ID: 643135 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(330) Version 1.10.9.0: ID: 618210 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(330) Version 1.10.1.0: ID: 516610 / Support ID: 400203957 add PhysicalStateChannels onX20SLX842 add PhysicalStateChannels on X20SLX842. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 539150 Adapt filter algorithm to eliminate dependencies between TON and TOF-filter Filter algorithm was adapted to eliminate dependencies between TON and TOF-filter which existed since FW V301. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 541650 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 549925 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 570155 Increase the tolerance of the voltage monitor The tolerance of the voltage monitor was increased to prevent sporadic false errors 99849 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(325) Version 1.10.0.6: ID: 532880 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532885 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532890 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\59384_1.fw(322) Version 1.10.0.3: ID: 473000 Improved stability The stability of the module was improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(322) Version 1.10.0.2: ID: 473375 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(320) |
|||||
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
| 2.1.0.0 | * | 05/07/2019 | 2 Mo | EXE | AS4_HW_X20SC0402.exe | |
| Description |
V4.6 HW Upgrade (X20SC0402) Revision information X20SC0402 Version 2.1.0.0: ID: 568710 Acknowledge several Channel errors with one ReleaseOutput edge. Several channel error of different types(HSHS, HSLS) are acknowledged with only one ReleaseOutput edge. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 596890 / Support ID: 400253825 cleared statement in help about open circuit detection cleared statement in help that the modulehas no open circuit detection Channel description changed: No Configuration description changed: No Firmware changed: No ID: 644155 major (even incompatible) changes for mapp Safety First upgrade formapp Safety. ATTENTION: existing applications must be adapted - see chapter "Switching to mapp Safety" in help! Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 10\59384_1.fw(570) Version 1.10.9.1: ID: 643135 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel descriptionchanged: No Configuration description changed: No Firmware changed:No Firmware: 1\59384_1.fw(330) Version 1.10.9.0: ID: 618210 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(330) Version 1.10.1.0: ID: 516610 / Support ID: 400203957 add PhysicalStateChannels on X20SLX842 add PhysicalStateChannels on X20SLX842. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 539150 Adapt filter algorithm to eliminate dependencies between TON and TOF-filter Filter algorithm was adapted to eliminate dependencies between TON and TOF-filter which existed since FW V301. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 541650 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No ID:549925 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 570155 Increase the tolerance of thevoltage monitor The tolerance of the voltage monitor was increased to prevent sporadic false errors 99849 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(325) Version 1.10.0.6: ID: 532880 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532885 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 532890 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\59384_1.fw(322) Version 1.10.0.3: ID: 473000 Improved stability The stability of the module was improved Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\59384_1.fw(322) Version 1.10.0.2: ID: 473375 first official release first official release Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\59384_1.fw(320) |
|||||
