DWL@DWL10000304723
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
|---|---|---|---|---|---|---|
| 2.17.0.0 | * | 05/14/2025 | 2 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.17.0.0: ID: RKFY-9500 Added capability to disable Fast Link Down detection In the event of interferences on the network cable, the active Fast Link Down Detection very quickly leads to a complete loss of thelink and thus to a failure of all subsequent stations. The Fast Link Down Detection can now be deactivated, which means that minor faults on the cable haveless impact. Channel description changed: No Configuration description changed: Yes Firmware changed: Yes Firmware: 1\7966_1.fw(438), 1\7966_3.fw(438), 1\7966_4.fw(438), 1\7966_5.fw(438), 1\7966_6.fw(438), 1\7966_7.fw(438) Version 2.16.0.0: ID: 772415 Continuous product improvement Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(436),1\7966_3.fw(436), 1\7966_4.fw(436), 1\7966_5.fw(436), 1\7966_6.fw(436), 1\7966_7.fw(436) Version 2.15.0.0: ID: 758510 Optimization of asynchronous register access Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(433), 1\7966_3.fw(433), 1\7966_4.fw(433), 1\7966_5.fw(433), 1\7966_6.fw(433), 1\7966_7.fw(433) Version 2.14.0.0: ID: 712665 POWERLINK Security Vulnerability (CVE-2020-13987 & CVE-2020-17438) POWERLINK Security Vulnerability (CVE-2020-13987) The POWERLINK IP stack was affectedby a security vulnerability impacting the checksum calculation of TCP/UDP packets. POWERLINK Security Vulnerability (CVE-2020-17438) The POWERLINK IP stack was affected by a security vulnerability impacting fragmented packet reassembly. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 720890 NUMBER:JACK improved ISN (TCP start sequence) generation in IP stack Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(432), 1\7966_3.fw(432), 1\7966_4.fw(432),1\7966_5.fw(432), 1\7966_6.fw(432), 1\7966_7.fw(432) Version 2.12.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration description changed: yes Firmware changed: no Version 2.11.1.0: ID: 695110 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 695280 Module documentation revised Data sheet V2.38 Channel description changed: No Configuration description changed: No Firmwarechanged: No Firmware: 1\7966_1.fw(430), 1\7966_3.fw(430), 1\7966_4.fw(430), 1\7966_5.fw(430), 1\7966_6.fw(430), 1\7966_7.fw(430) Version 2.11.0.0: ID: 519270 Accessing non-cyclic registers with AsIOAcc whileModuleOk = FALSE prevents module from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 631020 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 663630 DNA: Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 663720 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 666180 Module documentation revised Data sheet V2.37 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\7966_1.fw(430), 1\7966_3.fw(430), 1\7966_4.fw(430), 1\7966_5.fw(430), 1\7966_6.fw(430), 1\7966_7.fw(430) Version 2.10.0.0: ID: 624175 Optimization of the firmware update process Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(428), 1\7966_3.fw(428), 1\7966_4.fw(428), 1\7966_5.fw(428), 1\7966_6.fw(428), 1\7966_7.fw(428) Version 2.9.0.0: ID: 602705 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 611630 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 624130 DNA: BC as head-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 624385 Shortened preamble of Ethernet frame leading to incorrectly detectedCRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(427), 1\7966_3.fw(427), 1\7966_4.fw(427), 1\7966_5.fw(427), 1\7966_6.fw(427) Version 2.8.0.0: ID: 603160 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 608585 Outputs of I/O modules behind the bus coupler not working in some cases ifpoll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(426), 1\7966_3.fw(426), 1\7966_4.fw(426), 1\7966_5.fw(426), 1\7966_6.fw(426) Version 2.7.0.0: ID: 574890 Temporary toggling ofdata point ModuleOk if I/O module fails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(424), 1\7966_3.fw(424), 1\7966_4.fw(424), 1\7966_5.fw(424),1\7966_6.fw(424) Version 2.6.0.0: ID: 574205 Optimization of boot procedure for hardware variant 5 und 6 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(423), 1\7966_3.fw(423), 1\7966_4.fw(423), 1\7966_5.fw(423), 1\7966_6.fw(423) Version 2.5.6.0: ID: 564615 Optimization the boot up for hardware variant 5 Channel description changed:No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(422), 1\7966_3.fw(422), 1\7966_4.fw(422), 1\7966_5.fw(422) Version 2.5.5.0: ID: 548065 Startup time optimizations Channel description changed: No Configuration description changed:No Firmware changed: Yes Firmware: 1\7966_1.fw(421), 1\7966_3.fw(421), 1\7966_4.fw(421), 1\7966_5.fw(421) Version 2.5.4.0: ID: 539100 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(419), 1\7966_3.fw(419), 1\7966_4.fw(419) Version 2.5.3.0: ID: 517445 SDO streaming connection via UDP is not always established when PLC and BC arebooted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(417), 1\7966_3.fw(417), 1\7966_4.fw(417) Version 2.5.2.0: ID: 271540 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(415), 1\7966_3.fw(415), 1\7966_4.fw(415) Version 2.5.0.0: ID: 431950 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 465250 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 467335 Safety modules in connection with PLK BCs, with onlyinput datapoints, are not initialized.by SL Channel description changed:No Configuration description changed: No Firmware changed: Yes ID: 468515 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\7966_1.fw(413), 1\7966_3.fw(413), 1\7966_4.fw(413) Version 2.3.0.0: ID: 428150 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 437925 AS4.2.5 modifications Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 455930 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(411), 1\7966_3.fw(411), 1\7966_4.fw(411) Version 2.2.0.0: ID: 338175 Expansion for AR to detect the Ethernet port being used Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 380760 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 431210 I/Omodules behind POWERLINK bus controllers no longer achieving Operationalmodeafter multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(400), 1\7966_3.fw(400), 1\7966_4.fw(400) Version 2.1.0.0: ID: 393570 Upgrade 2.0.0.0 leads to a problem with WinIO switchboard Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 396220 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. Thesame problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(300), 1\7966_3.fw(300), 1\7966_4.fw(300) Version 2.0.0.0: ID: 385125 Uncommon X2X settings cause permanent boot of bus controller Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(210), 1\7966_3.fw(210), 1\7966_4.fw(210) Version 1.3.5.0: ID: 328265 Firmware of special I/O modules on POWERLINK bus controllers not updatingreliably when using an X2X cycle time less than 400 µs This problem occurs if the following conditions are met at the same time: - Firmware being updated on I/O modules on a POWERLINK bus controller - Some I/O modules using an older revision Current I/O module revisions are not affected. There is therefore no problem if a customer is replacing an old I/O module witha new I/O module on anexisting system. - X2X cycle time < 400 us - Short X2X cable length configured This problem does not occur if longer cable lengths are configured (e.g. the default value of 1000 m). Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(170), 1\7966_3.fw(170), 1\7966_4.fw(170) Version 1.3.4.0: ID: 299875 Expansion: Link- selector flag New datapoints:<br/>- RedundancyFirstLinkState<br/>- RedundancySecondLinkState Channel description changed: Yes Configuration description changed: Yes Firmware changed: No ID: 310065 POWERLINK V1: Bug-fix for Up/Downgrade POWERLINK V1 FW upgrade problem could be accored after PowerOn beginning with HW- Upgrade Version 1.3.1.0 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(168), 1\7966_3.fw(168), 1\7966_4.fw(168) Version 1.3.3.0: ID: 302500 ACOPOSmulti with SafeMC, asynchronous communication lost When there was a high load on the CPU, asynchronous communication to the buscontroller was interrupted.Restarting the boscontroller restored communication. Loss of asynchronous communication caused the safety-IO to stop. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(167), 1\7966_3.fw(167), 1\7966_4.fw(167) Version 1.3.2.0: ID: 295655 Problem with FW-Update of IO modules on Powerlink buscontrollers The firmware update of IO modules does not work in certain configurations. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(165), 1\7966_3.fw(165), 1\7966_4.fw(165) Version 1.3.1.0: ID: 288750 Certain X2X configurations don't work In very rare I/O constellations, the X2X modules don't start Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290070 New Hardwarevariant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(163), 1\7966_3.fw(163), 1\7966_4.fw(163) Version 1.3.0.0: ID: 240940 New X2X datapoints - NettimeOffsetX2X and NettimeX2X Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes ID: 274795 Support of 'Multiple Asynchronous Send' Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(160), 1\7966_3.fw(160) Version 1.2.1.0: ID: 247260 DNA runup upgraded Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(152), 1\7966_3.fw(152) Version 1.2.0.0: ID: 245095 DNA support; Update behavior on X2X bus of the BC improved - DNA support (Dynamic Node Allocation) - faster updating of modules with big FW files on the X2X busof the BC - new objects: 20A3h and 2000h/9 Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\7966_1.fw(150), 1\7966_3.fw(150) Version 1.0.8.0: ID: 218490 Extensions and Bugfixes - Firmware-Version is transferred via IdentResponse in the first 4 bytes ofthe field VendorSpecificExt1 - Support of PollResponse-Chaining Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(145) Version 1.0.7.0: ID: 214340 Extensions and Bugfixes - In systems with high X2X load it happened that IO modules were not restarted when the CPU did a warmstart (A&P 211805) - Activation of MultipleRead/Write feature for faster startup after configuration change - Writing to Objekt 20F0h/SubIndex 22 caused SDO errors when accessed faster than allowed - Number of configuration entries per IO module changed from 100 to 155 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(144) Version 1.0.6.0: ID: 210955 Extensions and Bugfixes - Error correction for operation in Powerlink V1 networks (A&P 210765) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(143) Version 1.0.5.0: ID: 210215 Extensions and Bugfixes - New ASICS will beset to 3mA output current (A&P 182905) - Optimization of SDO communication (unnecessary acknowledges removed) - Support of commands ReadMultipleParameter / WriteMultipleParameter - NodeID assignment by digital inputs supported (NodeId 241 and 242) - Minor corrections certification - ASnd frames with unknown ServiceID could disturb the BC (only possible with 3rd party MN) - Access to not existing objects in OD could cause firmware crash - When running X2X cycle times <200 us the X2X Bus was not working correctly (A&P 190630) - When in state PREOP_2 no SoC is received for 10sec the BC will fall back in PREOP_1 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\7966_1.fw(142) Version 1.0.4.1: ID: 183285 New info-/diagnostic data points, new FW 1.39 for signal filter and corrections New info-/diagnostic data points in HWC, new FW 1.39 for signal filter and corrections Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\7966_1.fw(141) Version 1.0.3.0: ID: 173310 Extensions and Bugfixes - Improvement of X2X Timings (Jitter reduced from 180ns to 20ns) (A&P167857 und 171987) - Optimizations for operation in 200us networks - 2 nodes with the same node number generated disturbance on the network (A&P 166040) - Functionsfor a new firmware download mechanism implemented (A&P 168537) Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\7966_1.fw(138) Version 1.0.2.0: ID: 164640 Extensions - Extensions for operation with Safety Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\7966_1.fw(136) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.16.0.0 | * | 11/29/2022 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.16.0.0: ID: 761215 Interface card was synchronized with old nettime Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(435), 1\57879_4.fw(435), 1\57879_5.fw(435) Version 2.15.0.0: ID: 758705 ModuleOk stucks TRUE if PCI card on expandable BC fails Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 758735 Optimization of asynchronous register access Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(433), 1\57879_4.fw(433), 1\57879_5.fw(433) Version 2.14.0.0: ID: 736475 No communication between PROFINET Controller and X20IF10E3-1 when no input datamapped and AR >= 4.91 is used Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 736535 POWERLINK Security Vulnerability (CVE-2020-13987 & CVE-2020-17438) POWERLINK Security Vulnerability (CVE-2020-13987) The POWERLINK IP stack was affected by a security vulnerability impacting thechecksum calculation of TCP/UDP packets. POWERLINK Security Vulnerability (CVE-2020-17438) The POWERLINK IP stack was affected by a security vulnerability impacting fragmented packet reassembly. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 736570 NUMBER:JACK improved ISN (TCP start sequence) generation in IP stack Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 739430 Module documentation revised Data sheet V2.51 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(432), 1\57879_4.fw(432), 1\57879_5.fw(432) Version 2.13.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed:no Configuration description changed: yes Firmware changed: no Version 2.12.0.0: ID: 703010 FW Update of the X2X modules connected to the X20IF1091-1 at each startup (Rev. >= I0) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(431), 1\57879_4.fw(431), 1\57879_5.fw(431) Version 2.11.1.0: ID: 695155 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 695455 Module documentation revised Data sheet V2.49 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.11.0.0: ID: 664385 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664400 DNA: Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665765 / Support ID: 400266182, 400285939 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665845 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 666210 Module documentation revised Data sheet V2.48 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 678955 Support HW-variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628965 Wrong serial number in SystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 /Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O module fails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration descriptionchanged: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolatedcases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed:No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takesup to 5s. Channel description changed: No Configuration descriptionchanged: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLXhinterBC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes areaddedor removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed:No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.15.0.0 | * | 10/13/2022 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.15.0.0: ID: 758705 ModuleOk stucks TRUE if PCI card on expandable BC fails Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 758735 Optimization of asynchronous register access Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(433), 1\57879_4.fw(433), 1\57879_5.fw(433) Version 2.14.0.0: ID: 736475 No communication between PROFINET Controllerand X20IF10E3-1 when no input data mapped and AR >= 4.91 is used Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 736535 POWERLINK Security Vulnerability (CVE-2020-13987 & CVE-2020-17438) POWERLINK Security Vulnerability (CVE-2020-13987) The POWERLINK IP stack was affected by a security vulnerability impacting thechecksum calculation of TCP/UDP packets. POWERLINK Security Vulnerability (CVE-2020-17438) The POWERLINK IP stack was affected by a security vulnerability impacting fragmented packet reassembly. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 736570 NUMBER:JACK improved ISN (TCP start sequence) generation in IP stack Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 739430 Module documentation revised Data sheet V2.51 Channel descriptionchanged: No Configuration description changed: No Firmware changed:No Firmware: 1\57879_3.fw(432), 1\57879_4.fw(432), 1\57879_5.fw(432) Version 2.13.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration description changed:yes Firmware changed: no Version 2.12.0.0: ID: 703010 FW Update of the X2X modules connected to the X20IF1091-1 at each startup (Rev. >= I0) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(431), 1\57879_4.fw(431), 1\57879_5.fw(431) Version 2.11.1.0: ID: 695155 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 695455 Module documentation revised Data sheet V2.49 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.11.0.0: ID: 664385 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664400 DNA:Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665765 / Support ID: 400266182, 400285939 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665845 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 666210 Module documentation revised Data sheet V2.48 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 678955 Support HW-variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628965 Wrong serial number in SystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed:No Configuration description changed: No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the nextnode not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O module fails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / SupportID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 /Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235/ Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal"bei CPU PowerCycle wenn SLXhinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.14.0.0 | * | 10/18/2021 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.14.0.0: ID: 736475 No communication between PROFINET Controller and X20IF10E3-1 when no input data mapped and AR >= 4.91 is used Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 736535 POWERLINK Security Vulnerability (CVE-2020-13987 & CVE-2020-17438) POWERLINK Security Vulnerability (CVE-2020-13987) The POWERLINK IP stack was affected by a security vulnerability impacting thechecksum calculation of TCP/UDP packets. POWERLINK Security Vulnerability (CVE-2020-17438) The POWERLINK IP stack was affected by a security vulnerability impacting fragmented packet reassembly. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 736570 NUMBER:JACK improved ISN (TCP startsequence) generation in IP stack Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 739430 Module documentation revised Data sheet V2.51 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(432), 1\57879_4.fw(432), 1\57879_5.fw(432) Version 2.13.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration description changed: yes Firmware changed: no Version 2.12.0.0: ID: 703010 FW Update of the X2X modules connected to the X20IF1091-1 at each startup (Rev. >= I0) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(431), 1\57879_4.fw(431), 1\57879_5.fw(431) Version 2.11.1.0: ID:695155 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 695455 Module documentation revised Data sheet V2.49 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.11.0.0: ID: 664385 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664400 DNA: Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665765 / Support ID: 400266182, 400285939 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665845 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 666210 Module documentation revised Data sheet V2.48 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 678955 Support HW-variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed:No Firmware changed: Yes ID: 628965 Wrong serial number inSystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closesthe ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O module fails Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes ID: 468105 / Support ID: 400177243 X2X FW update of severalX2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel description changed: No Configurationdescription changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operationalmode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID:460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behindPOWERLINK bus controllers no longer achieving Operationalmode after multiplepower-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware:1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.13.0.0 | * | 07/23/2021 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.13.0.0: ID: Adaptations for Automation Studio 4.11 Channel description changed: no Configuration description changed: yes Firmware changed: no Version 2.12.0.0: ID: 703010 FW Update of the X2X modules connected to the X20IF1091-1 at each startup (Rev. >= I0) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(431), 1\57879_4.fw(431), 1\57879_5.fw(431) Version 2.11.1.0: ID: 695155 Support for automatic DNA configuration from AS 4.9.1 Channel descriptionchanged: No Configuration description changed: Yes Firmware changed: No ID: 695455 Module documentation revised Data sheet V2.49 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.11.0.0: ID: 664385 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664400 DNA: Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665765 / Support ID: 400266182, 400285939 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665845 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 666210 Module documentation revised Data sheet V2.48 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 678955 Support HW-variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628965 Wrong serial number in SystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end stationswitching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling ofdata point ModuleOk if I/O module fails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 /Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart ofthe netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modulesbehind POWERLINK bus controllers no longer achieving Operationalmode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes areplugged or unplugged on the end of the X2XLink thediagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.12.0.0 | * | 10/08/2020 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.12.0.0: ID: 703010 FW Update of the X2X modules connected to the X20IF1091-1 at each startup (Rev. >= I0) Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(431), 1\57879_4.fw(431), 1\57879_5.fw(431) Version 2.11.1.0: ID: 695155 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 695455 Module documentation revised Data sheet V2.49 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.11.0.0: ID: 664385 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664400 DNA: Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665765 / Support ID: 400266182, 400285939 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665845 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 666210 Module documentation revised Data sheet V2.48 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 678955 Support HW-variant 4 Channeldescription changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628965 Wrong serial number in SystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O modulefails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed:No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / SupportID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connectionvia UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel descriptionchanged: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.11.1.0 | * | 08/24/2020 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.11.1.0: ID: 695155 Support for automatic DNA configuration from AS 4.9.1 Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 695455 Module documentation revised Data sheet V2.49 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.11.0.0: ID: 664385 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664400 DNA: Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665765 / Support ID: 400266182,400285939 ModuleOk of IO module FALSE after warm restart even though themodule is working as expected Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665845 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 666210 Module documentation revised Data sheet V2.48 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 678955 Support HW-variant 4 Channel description changed: No Configuration description changed: No Firmwarechanged: Yes Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628965 Wrong serial number in SystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed: No Configuration description changed:No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end station switching hub off again Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frameleading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / SupportID: 400241376 Temporary toggling of data point ModuleOk if I/O module fails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.bySL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 468540 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115/ Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed:No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. Thedata point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmwarechanged: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.11.0.0 | * | 02/10/2020 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.11.0.0: ID: 664385 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 664400 DNA: Hub of PLK BC active until first IDENT_REQUEST Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 665765 /Support ID: 400266182, 400285939 ModuleOk of IO module FALSE after warm restart even though the module is working as expected Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes ID: 665845 Accessing non-cyclic registers with AsIOAcc while ModuleOk = FALSE preventsmodule from starting/communicating Channel description changed: No Configuration description changed: No Firmwarechanged: Yes ID: 666210 Module documentation revised Data sheet V2.48 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 678955 Support HW-variant 4 Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(430), 1\57879_4.fw(430) Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628965 Wrong serial number in SystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end station switching huboff again Channel description changed: No Configuration descriptionchanged: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled inrare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O module fails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDsfor hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints,are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when emptybackplanes are addedor removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implementedto update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.9.0.0 | * | 02/15/2019 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.9.0.0: ID: 623855 Optimization of synchronization between X20BC1083 and X20IF1091-1 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628940 Optimization of hub behavior Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 628965 Wrong serial number in SystemDump when X20IF1091-1 is used on a X20BC1083 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629020 Ring redundancy: Cannot address the CN that closes the ring Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629085 DNA: BC as head-end station switching hub off again Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 629170 Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(427) Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O modulefails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed:No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / SupportID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connectionvia UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel descriptionchanged: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.8.0.0 | * | 12/05/2018 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.8.0.0: ID: 619155 DNA: PLK hub forwarding for the next node not enabled in rare cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 619190 Outputs of I/O modules behind the bus coupler not working in some cases if poll-response chaining active Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 623065 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(426) Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O module fails Channel description changed:No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netXIF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware:1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID:523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with onlyinput datapoints, are not initialized.by SL Channel description changed:No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 /Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID:400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-oncycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanesare plugged or unplugged on the end of the X2XLink thediagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.7.0.0 | * | 04/17/2018 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.7.0.0: ID: 586750 / Support ID: 400241376 Temporary toggling of data point ModuleOk if I/O module fails Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(424) Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startuptime optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / Support ID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connection via UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASndSDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 causeservice of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card isreset by the Bus Controller Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel descriptionchanged: No Configuration description changed: No Firmware changed:Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration descriptionchanged: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problemalso occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
| Versão | Idiomas | Sistema operacional | Data | Tamanho | Tipos | Download |
| 2.6.0.0 | * | 02/09/2018 | 1 MB | EXE | AS4_HW_X20cBC1083.exe | |
| Descrição |
V4.0 HW Upgrade (X20cBC1083) Revision information X20cBC1083 Version 2.6.0.0: ID: 572710 Corrected L/A LEDs for hardware revision H0 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 574320 / Support ID: 0, 400235528, 400235970 Unable to start netX IF card on X20BC1083 in isolated cases Channel description changed: No Configuration description changed:No Firmware changed: Yes ID: 574325 / Support ID: 400230671 Error 30285 with error code 0x8047 after changing the netX configuration Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(423) Version 2.5.6.0: ID: 551130 Startup time optimizations Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(421) Version 2.5.5.0: ID: 545100 NetX Firmware update bug fix Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(420) Version 2.5.4.0: ID: 540325 / SupportID: 400202320 BC sporadically not going into Operational due to X2X-bus problems at startup Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(419) Version 2.5.3.0: ID: 523495 / Support ID: 400205694 safety modules not switching to operational state SDO streaming connectionvia UDP is not always established when PLC and SafeLogic are booted together. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(417) Version 2.5.2.0: ID: 493895 / Support ID: 400103115, 400101850, 400154063, 400190752 First POWERLINK UDP ASnd SDO transfert after long time takes up to 5s. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494195 / Support ID: 400191269 X20BC1083 with disabled netX modules is not booting - Error 32162 Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 494200 / Support ID: 400189834 X20IF1091-1 + X20BC1083 + X20IF10E1-1 cause service of PLC and error 30023 in logger Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(415) Version 2.5.0.0: ID: 467890 Restart of the netX interface card If PLK-failure the netX interface card is reset by the Bus Controller Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 468100 / Support ID: 400178654 Safety modules in connection with PLK BCs, with only input datapoints, are not initialized.by SL Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468105 / Support ID: 400177243 X2X FW update of several X2X modules is not working Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 468110 optimization of X2X FW updates Channeldescription changed: No Configuration description changed: No Firmware changed: Yes ID: 468540 CiR support Channel descriptionchanged: No Configuration description changed: Yes Firmware changed: No Firmware: 1\57879_3.fw(413) Version 1.3.0.0: ID: 460115 / Support ID: 400168329 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 460235 / Support ID: 400150525 Error 114834 "Fehler interner SLX-Kommandokanal" bei CPU PowerCycle wenn SLX hinter BC Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(411) Version 1.2.0.0: ID: 439110 / Support ID: 400150496 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 439215 / Support ID: 400128436 I/O modules behind POWERLINK bus controllers no longer achieving Operational mode after multiple power-on cycles Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(400) Version 1.1.0.0: ID: 402430 X2XLink-BC: StationAtBusEnd does not change, when empty backplanes are added or removed. When empty backplanes are plugged or unplugged on the end of the X2XLink the diagnostic data point "StationAtBusEnd" die not change. The data point die change when IO Modules were removed or added. A new handshake between Automation Runtime and firmware was implemented to update the "StationAtBusEnd" faster. The same problem also occurs with modules where the X2XLink is supplied with power, but the supply for the IO is missing. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes Firmware: 1\57879_3.fw(300) Version 1.0.0.1: ID: 343245 Support X20cBC1083 Support for Automation Studio Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\57879_3.fw(210) |
|||||
