X20DI2377

Short description
I/O module 2 digital inputs 24 VDC for 3-wire connections, special functions
General information
B&R ID code 0x1B8E
Status indicators I/O function per channel, operating state, module status
Diagnostics
Module run/error Yes, using LED status indicator and software
Power consumption
Bus 0.15 W
Internal I/O 0.82 W
Additional power dissipation caused by actuators (resistive) [W] -
Certifications
CE Yes
UKCA Yes
CRA (Cyber Resilience Act) In preparation
ATEX Zone 2, II 3G Ex nA nC IIA T5 Gc
IP20, Ta (see X20 user's manual)
FTZÚ 09 ATEX 0083X
UL cULus E115267
Industrial control equipment
HazLoc cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5
DNV Temperature: B (0 to 55°C)
Humidity: B (up to 100%)
Vibration: B (4 g)
EMC: B (bridge and open deck)
CCS Yes
LR ENV1
KR Yes
ABS Yes
BV EC33B
Temperature: 5 - 55°C
Vibration: 4 g
EMC: Bridge and open deck
KC Yes
Digital inputs
Nominal voltage 24 VDC
Input characteristics per EN 61131-2 Type 1
Input voltage 24 VDC -15% / +20%
Input current at 24 VDC Typ. 10.5 mA
Input circuit Sink
Input filter
Hardware ≤10 μs
Software Default 0 ms, configurable between 0 and 25 ms in 0.2 ms intervals
Connection type 3-wire connections
Input resistance Typ. 2.23 kΩ
Additional functions 50 kHz event counting, gate measurement
Switching threshold
Low <5 VDC
High >15 VDC
Insulation voltage between channel and bus 500 Veff
Event counters
Quantity 2
Signal form Square wave pulse
Evaluation Each positive edge, cyclic counter
Input frequency Max. 50 kHz
Counter 1 Input 1
Counter 2 Input 2
Counter frequency Max. 50 kHz
Counter size 16-bit
Gate time measurement
Number of gate time measurements 1
Signal form Square wave pulse
Evaluation Positive edge - Negative edge
Counter frequency
Internal 48 MHz, 24 MHz, 12 MHz, 6 MHz, 3 MHz, 1.5 MHz, 750 kHz, 375 kHz, 187.5 kHz
Counter size 16-bit
Length of pause between pulses ≥100 µs
Pulse length ≥20 µs
Supported inputs Input 1 or input 2
Sensor power supply
Power consumption Max. 12 W
Voltage Module power supply minus voltage drop for short-circuit protection
Voltage drop for short-circuit protection at 500 mA Max. 2 VDC
Summation current 0.5 A
Short-circuit proof Yes
Electrical properties
Electrical isolation Channel isolated from bus
Channel not isolated from channel
Operating conditions
Mounting orientation
Horizontal Yes
Vertical Yes
Installation elevation above sea level
0 to 2000 m No limitation
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Horizontal mounting orientation -25 to 60°C
Vertical mounting orientation -25 to 50°C
Derating -
Storage -40 to 85°C
Transport -40 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Mechanical properties
Note Order 1x terminal block X20TB06 or X20TB12 separately.
Order 1x bus module X20BM11 separately.
Pitch 12.5+0.2 mm
Référence produit:
X20DI2377
Description:
  • 2 digital inputs
  • Sink connection
  • 3-wire connections
  • 2 counter inputs with 50 kHz counter frequency
  • Gate measurement
  • 24 VDC and GND for sensor supply
  • Software input filter can be configured for entire module

The module is equipped with two inputs for 3-wire connections. Both inputs can be configured as event counters. Gate measurement is only ever possible on one channel.

This module is designed for X20 6-pin terminal blocks. If needed (e.g. for logistical reasons), the 12-pin terminal block can also be used.

Accessoires obligatoires
Bus modules
X20BM11 X20 bus module, 24 VDC keyed, internal I/O power supply connected through
X20BM15 X20 bus module, with node number switch, 24 VDC keyed, internal I/O power supply connected through
Terminal blocks
X20TB06 X20 terminal block, 6-pin, 24 VDC keyed
X20TB12 X20 terminal block, 12-pin, 24 VDC keyed
Automation Studio HW Upgrades Version (date) Téléchargement
V2.6 HW Upgrade (X20DI2377) EXE / 421 Ko
V2.6 HW Upgrade (X20DI2377) EXE / 940 Ko
V3.0 HW Upgrade (X20DI2377) EXE / 420 Ko
V3.0 HW Upgrade (X20DI2377) EXE / 1 Mo
V4.0 HW Upgrade (X20DI2377) EXE / 1 Mo
Certifications Version (date) Téléchargement
2226379 CSA Certificate of Compliance X20 X67 PDF / 366 Ko
ABS Certificate of Product Design Assessment - X20 IO Series PDF / 454 Ko
BV Type Approval Certificate - X20 PDF / 556 Ko
CCS Type Approval Certificate - X20 PDF / 285 Ko
E115267 UL Certificate of Compliance X20 PDF / 2 Mo
EU Data Act - X20 IO - Connected Product Information Notice PDF / 92 Ko
EU Declaration ATEX X20 PDF / 218 Ko
EU Declaration of conformity PLC X20 PDF / 169 Ko
FTZU 09 ATEX 0083X PDF / 771 Ko
KR Type Approval Certificate MIL39390-AC003 (X20 System) PDF / 320 Ko
Lloyds Register (X20 only) PDF / 884 Ko
RINA Type Approval Certificate - X20 / Power Panel T30 PDF / 1 Mo
TAA00000BJ DNV Type Approval Certificate X20 PDF / 191 Ko
UK Declaration PLC X20 PDF / 151 Ko
X20, X67 KC certificates PDF / 6 Mo
Documentation Version (date) Téléchargement
Data sheet X20DI2377 PDF / 794 Ko
X20 Package leaflet ATEX/CSA PDF / 2 Mo
X20 System User´s Manual PDF / 49 Mo
E-CAD (modèles Electro ou EPLAN) Version (date) Téléchargement
X20 EPLAN P8 from V2.4 EXE / 160 Mo
M-CAD (modèles mécaniques) Version (date) Téléchargement
3D File DXF/STEP X20 Electronic module ZIP / 10 Ko
3D File STEP X20 I/O-Slice ZIP / 872 Ko
Dimensions PDF X20 Electronic module PDF / 3 Ko

Veuillez sélectionner un pays et une langue

B&R Logo