Lütfen ülke ve dil seçiniz

Short description
Bus controller DeviceNet adapter (slave)
General information
B&R ID code 0x1F1B
Status indicators Module status, bus function, 24V DeviceNet voltage, data transfer, terminating resistor.
24 V DeviceNet voltage Yes, with LED status indicators (MOD and NET)
Module status Yes, using status LED and software
Bus function Yes, using status LED
Data transfer Yes, using status LED
Terminating resistor Yes, using status LED
Power consumption
Bus 1.5 W
Additional power dissipation caused by actuators (resistive) [W] -
CE Yes
ATEX Zone 2, II 3G Ex nA nC IIA T5 Gc
IP20, Ta (see X20 user's manual)
FTZÚ 09 ATEX 0083X
UL cULus E115267
Industrial control equipment
HazLoc cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5
DNV GL Temperature: B (0 - 55°C)
Humidity: B (up to 100%)
Vibration: B (4 g)
EMC: B (bridge and open deck)
KR Yes
KC Yes
Fieldbus DeviceNet adapter (slave)
Variant 5-pin male multipoint connector
Max. distance 500 m
Transfer rate Max. 500 kbit/s
Default transfer rate Automatic transfer rate detection
Min. cycle time
Fieldbus No limitations
X2X Link 400 μs
Synchronization between bus systems possible No
Terminating resistor Integrated in the module
Electrical properties
Electrical isolation DeviceNet isolated from I/O
DeviceNet not isolated from bus
Operating conditions
Mounting orientation
Horizontal Yes
Vertical Yes
Installation elevation above sea level
0 to 2000 m No limitations
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP20
Ambient conditions
Horizontal mounting orientation -25 to 60°C
Vertical mounting orientation -25 to 50°C
Derating -
Storage -40 to 85°C
Transport -40 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Mechanical properties
Note Order 1x TB2105 terminal block separately
Order 1x X20TB12 terminal block separately
Order 1x X20PS9400 or X20PS9402 power supply module separately
Order 1x X20BB80 bus base separately
Pitch 37.5 +0.2 mm
Malzeme Numarası:
  • Fieldbus: DeviceNet
  • I/O configuration via the fieldbus
  • Support of both linear and modular (Allen Bradley) configuration systems
  • Auto scan, automatic I/O mapping of the I/Os
  • Automatic I/O configuration (starting with Rev. D0, firmware version 1.23)
  • Integrated terminating resistor

DeviceNet was developed by Allen Bradley as a CAN bus based automation network. It is based on a producer/consumer protocol. From the user's point of view, all data is handled separately from CAN bus transfer possibilities (e.g. longer data packets are automatically fragmented by DeviceNet). Access occurs using I/O messages with defined properties.

The bus controller makes it possible to connect X2X Link I/O nodes to DeviceNet. It has automatic transfer rate detection, auto scan, automatic mapping and automatic configuration of the I/O modules. Explicit messaging, change of state, cyclic, polled and bit strobe are supported as transfer modes. In addition to the standard communication objects, there are also manufacturer-specific objects used to represent the modular X20 System in the best manner possible.

X20 and other modules that are based on X2X Link can be connected to the bus controller. The entire configuration of this type of modular system is supported by the DeviceNet standard. Allen Bradley developed the modular I/O configuration to simplify the necessary configuration steps. The DeviceNet bus controllers from B&R also support this type of configuration.

Gerekli aksesuarlar
System modules for bus controllers
X20BB80 X20 bus base, for X20 base module (BC, HB, etc.) and X20 power supply module, X20 end plates (left and right) X20AC0SL1/X20AC0SR1 included
X20PS9400 X20 power supply module, for bus controller and internal I/O power supply, X2X Link power supply
X20PS9402 X20 power supply module, for bus controller and internal I/O power supply, X2X Link power supply, supply not electrically isolated
Terminal blocks
0TB2105.9010 Accessory terminal block, 5-pin, screw clamps 2.5 mm²
0TB2105.9110 Accessory terminal block, 5-pin, push-in terminal block 2.5 mm²
X20TB12 X20 terminal block, 12-pin, 24 VDC keyed
Dokümantasyon Version (Date) Download
Data sheet X20BC0053 PDF / 205 KB
X20 System User´s Manual PDF / 56 MB
E-CAD (Elektrik veya EPLAN Taslakları) Version (Date) Download
X20 EPLAN P8 from V2.4 EXE / 161 MB
Fieldbus Donanım Tanımlama Dosyaları Version (Date) Download
X20BC0053 EDS Package ZIP / 243 KB
M-CAD (Mekanik Taslaklar) Version (Date) Download
3D File DXF/STEP X20 Bus Controller CAN/DeviceNet ZIP / 28 KB
Dimensions PDF X20 Bus Controller CAN/DeviceNet PDF / 4 KB
Sertifikalar Version (Date) Download
244665 CSA HazLoc Certificate of Compliance X20, X67 PDF / 56 KB
ABS Type Approval Certificate - X20 IO Series PDF / 2 MB
DNV GL Type Approval Certificate - X20 / Power Panel T30 PDF / 164 KB
E115267 UL CoC X20 PDF / 847 KB
FTZU 09 ATEX 0083X PDF / 697 KB
KR Type Approval Certificate MIL39390-AC003 (X20 System) PDF / 758 KB
Lloyds Register PDF / 506 KB

Lütfen ülke ve dil seçiniz

B&R Logo