Выберите регион и язык:

Short description
Stepper motor Stepper motor flange size 60 mm, length 138.6 mm, SSI encoder
General information
Certifications
CE Yes
EAC Yes
Specific motor data
Wiring Serial
Current 2.5 A
Resistance/Phase 2.4 Ω
Inductance/Phase 11.2 mH
Stall torque 2.5 Nm
Holding torque 3.5 Nm
Detent torque <75 mNm
Rotor inertia 920 gcm2
General motor data
Stepping angle 1.8°
Max. surface temperature 95°C
Average period of operation between failures 21,000 hours
Shaft type Flat-sided (D-cut)
Insulation class B (130°C)
Insulation resistance 100 MΩ min. 500 VDC
Dielectric resistance 500 VAC for 1 minute
Driver supply voltage Max. 80 VDC
Operating conditions
Degree of protection per EN 60529 IP65
Ambient conditions
Temperature
Operation -20 to 40°C
Storage -30 to 85°C
Transport -30 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Electrical properties - Encoder
Number of outputs 4
Data / nData / CLK / nCLK
Resolution 4096 increments per revolution
Output circuit Differential signal
Output protection Short circuit protection
Current consumption Max. 16 mA + output load
Supply voltage 18 to 30 VDC
Max. output current ±25 mA per output
Data format Gray
Counting direction Clockwise
Clock frequency Max. 400 kHz
Mechanical properties
Max. radial load 75 N
Max. axial load The permitted axial load must not be larger than the motor mass
Weight 1,500 g
Length 138.6 mm
Артикул:
80MPF5.250S113-01
Описание:
2-phase hybrid stepper motor, 60 mm flange, length 139 mm, SSI 24 VDC, 2.5 A series, 3.5 Nm holding torque, 2.5 Nm stall torque
Дополнительные аксессуары
Accessories
80XMPXAC0.00-01 Accessory for stepper motors with encoder, 8-pin and 4-pin connector + crimp contacts
80XMPXAC1.00-10 Sealing for IP65 stepper motors for usage with 80CMxxxxx.26-01 cables, 10 units per package
Motor cables
80CM01001.21-01 Motor cable, length 1 m, 5x 0.75 mm², 4-pin connector on the motor side, can be used in cable drag chains, , UL listed
80CM01501.21-01 Motor cable, length 1.5 m, 5x 0.75 mm², 4-pin male connector on the motor side, can be used in cable drag chains, UL listed
80CM02001.21-01 Motor cable, length 2 m, 5x 0.75 mm², 4-pin connector on the motor side, can be used in cable drag chains, , UL listed
80CM03001.21-01 Motor cable, length 3 m, 5x 0.75 mm², 4-pin connector on the motor side, can be used in cable drag chains, , UL listed
80CM05001.21-01 Motor cable, length 5 m, 5x 0.75 mm², 4-pin connector on the motor side, can be used in cable drag chains, , UL listed
80CM10001.21-01 Motor cable, length 10 m, 5x 0.75 mm², 4-pin connector on the motor side, can be used in cable drag chains, , UL listed
80CM15001.21-01 Motor cable, length 15 m, 5x 0.75 mm², 4-pin connector on the motor side, can be used in cable drag chains, , UL listed
80CM20001.21-01 Motor cable, length 20 m, 5x 0.75 mm², 4-pin connector on the motor side, can be used in cable drag chains, , UL listed
SSI encoder cables
80CM01004.25-01 SSI encoder cable, length 1 m, 4x 0.14 mm², 4x 0.34 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM02004.25-01 SSI encoder cable, length 2 m, 4x 0.14 mm², 4x 0.34 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM03004.25-01 SSI encoder cable, length 3 m, 4x 0.14 mm², 4x 0.34 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM05004.25-01 SSI encoder cable, length 5 m, 4x 0.14 mm², 4x 0.34 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM10004.25-01 SSI encoder cable, length 10 m, 4x 0.14 mm², 4x 0.34 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM15004.25-01 SSI encoder cable, length 15 m, 4x 0.14 mm², 4x 0.34 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM20004.25-01 SSI encoder cable, length 20 m, 4x 0.14 mm², 4x 0.34 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
Документация Version (Date) Download
Stepper motors user's manual PDF / 15 MB

Выберите регион и язык:

B&R Logo