Выберите регион и язык:

Short description
Stepper motor Stepper motor flange size 60 mm, length 184.4 mm, incremental encoder and brake
General information
Certifications
CE Yes
EAC Yes
Specific motor data
Wiring Parallel
Current 5 A
Resistance/Phase 0.6 Ω
Inductance/Phase 2.8 mH
Stall torque 2.5 Nm
Holding torque 3.5 Nm
Detent torque <75 mNm
Rotor inertia 920 gcm2
General motor data
Stepping angle 1.8°
Max. surface temperature 90°C
Average period of operation between failures 21,000 hours
Shaft type Flat-sided (D-cut)
Insulation class B (130°C)
Insulation resistance 100 MΩ min. 500 VDC
Dielectric resistance 500 VAC for 1 minute
Driver supply voltage Max. 80 VDC
Operating conditions
Degree of protection per EN 60529 IP65
Ambient conditions
Temperature
Operation -20 to 40°C
Storage -30 to 85°C
Transport -30 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Electrical properties - Encoder
Number of outputs 3
A / B / R
Resolution 1024 increments per revolution
Output circuit Push / Pull level, asymmetric
Output protection Short circuit protection
Current consumption Max. 12 mA + output load
Supply voltage 18 to 30 VDC
Max. output current ±10 mA per output
Electrical properties - Brake
Supply voltage 24 VDC +6% / -10%
Braking torque 2 Nm / 1.5 Nm / 1.8 Nm
Coil resistance 52.36 Ω ±7%
Inductance 0.7 H
Power consumption Typ. 11 W
Connection time 6 ms
Response delay 2 ms
Cutoff time 25 ms
Mechanical properties
Max. radial load 75 N
Max. axial load The permitted axial load must not be larger than the motor mass
Weight 1,800 g
Length 184.4 mm
Артикул:
80MPF5.500D114-01
Описание:
2-phase hybrid stepper motor, 60 mm flange, length 183.8 mm, ABR 24 VDC, 5 A parallel, brake 2 Nm, 3.5 Nm holding torque, 2.5 Nm stall torque
Дополнительные аксессуары
Accessories
80XMPXAC0.00-02 Accessory for stepper motors with encoder + brake, 8-pin, 4-pin and 2-pin connector + crimp contacts
80XMPXAC1.00-10 Sealing for IP65 stepper motors for usage with 80CMxxxxx.26-01 cables, 10 units per package
Incremental encoder cables
80CM01003.25-01 Incremental encoder cable, length 1 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM02003.25-01 Incremental encoder cable, length 2 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM03003.25-01 Incremental encoder cable, length 3 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM05003.25-01 Incremental encoder cable, length 5 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM07503.25-01 Incremental encoder cable, length 7.5 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM10003.25-01 Incremental encoder cable, length 10 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM15003.25-01 Incremental encoder cable, length 15 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
80CM20003.25-01 Incremental encoder cable, length 20 m, 4x 0.14 mm², 2x 0.35 mm², 8-pin connector on the motor side, 9-pin DSUB connector on the drive side, can be used in cable drag chains, UL listed
Motor cables with brake
80CM01002.21-01 Motor cable, length 1 m, 5x 0.75 mm², 2x 0.5 mm², for stepper motors with brake, 4-pin and 2-pin connectors on the motor side, can be used in cable drag chains, UL listed
80CM02002.21-01 Motor cable, length 2 m, 5x 0.75 mm², 2x 0.5 mm², for stepper motors with brake, 4-pin and 2-pin connectors on the motor side, can be used in cable drag chains, UL listed
80CM03002.21-01 Motor cable, length 3 m, 5x 0.75 mm², 2x 0.5 mm², for stepper motors with brake, 4-pin and 2-pin connectors on the motor side, can be used in cable drag chains, UL listed
80CM05002.21-01 Motor cable, length 5 m, 5x 0.75 mm², 2x 0.5 mm², for stepper motors with brake, 4-pin and 2-pin connectors on the motor side, can be used in cable drag chains, UL listed
80CM10002.21-01 Motor cable, length 10 m, 5x 0.75 mm², 2x 0.5 mm², for stepper motors with brake, 4-pin and 2-pin connectors on the motor side, can be used in cable drag chains, UL listed
80CM15002.21-01 Motor cable, length 15 m, 5x 0.75 mm², 2x 0.5 mm², for stepper motors with brake, 4-pin and 2-pin connectors on the motor side, can be used in cable drag chains, UL listed
80CM20002.21-01 Motor cable, length 20 m, 5x 0.75 mm², 2x 0.5 mm², for stepper motors with brake, 4-pin and 2-pin connectors on the motor side, can be used in cable drag chains, UL listed
Документация Version (Date) Download
Stepper motors user's manual PDF / 15 MB

Выберите регион и язык:

B&R Logo