Выберите регион и язык:

General information
Cooling Fanless
B&R ID code 0xE570
System requirements
Automation Studio 4.1.4.375 and later
Automation Runtime K4.08 and later
Support of X20SLX modules Rev. B4 and later
Power button No
Reset button Yes
Status indicators Supply voltage OK, operating state, module status, POWERLINK, Ethernet, CAN Rx/Tx, RS485 Rx/Tx
Buzzer Yes
Support
Controller redundancy possible No
ACOPOS support Yes
Visual Components support Yes
Certifications
CE Yes
UL cULus E115267
Industrial control equipment
EAC Yes
Controller
Bootloader Automation Runtime AR 4.08
Real-time clock Nonvolatile, 1 s resolution, -10 to 10 ppm accuracy at 25°C
FPU Yes
Processor
Type Atom E620T
Clock frequency 333 MHz (compatible)
L1 cache
Data code 24 kB
Program code 32 kB
L2 cache -
Mode/Node switches No
Remanent variables 32 kB FRAM, buffering >10 years
DRAM 256 MB
Shortest task class cycle time 0.4 ms
Typical instruction cycle time 0.01 µs
Application memory
Type 2 GB eMMC flash memory
Data retention 10 years
Writable data amount
Guaranteed 40 TB
Results for 5 years 21.9 GB/day
Guaranteed erase/write cycles 20,000
Error-correcting code (ECC) Yes
Temperature cutoff Yes, at >88°C
Display
Type TFT color
Diagonal 7.0"
Colors 16.7 million (RGB, 8 bits per channel)
Resolution WVGA, 800 x 480 pixels
Contrast Typ. 600:1
Viewing angles
Horizontal Direction L / Direction R = Typ. 70°
Vertical Direction U / Direction D = Typ. 60°
Backlight
Type LED
Brightness Typ. 500 cd/m²
Half-brightness time 50,000 h
Touch screen
Type AMT
Technology Analog resistive
Controller B&R, serial, 12-bit
Transmittance 80% ±3%
Screen rotation Yes, using per Visual Components
Interfaces
Interface IF1
Fieldbus POWERLINK V2 managing or controlled node
Type Type 4
Variant 1x RJ45 shielded
Cable length Max. 100 m between 2 nodes (segment length)
Max. transfer rate 100 Mbit/s
Transfer
Physical layer 100BASE-TX
Half-duplex Yes
Full-duplex POWERLINK mode: No / Ethernet mode: Yes
Autonegotiation Yes
Auto-MDI/MDIX Yes
Interface IF2
Type Ethernet
Variant 1x RJ45 shielded
Cable length Max. 100 m between 2 nodes (segment length)
Max. transfer rate 10/100 Mbit/s
Transfer
Physical layer 10BASE-T/100BASE-TX
Half-duplex Yes
Full-duplex Yes
Autonegotiation Yes
Auto-MDI/MDIX Yes
Interface IF3
Type USB 2.0
Variant Type A
Current-carrying capacity 0.49 A
Interface IF4
Type USB 2.0
Variant Type A
Current-carrying capacity ≥Rev. E0: 0.20 A
<Rev. E0: 0.10 A
Interface IF5
Fieldbus X2X Link master
Interface IF6
Type CAN bus
Variant 3 pins of the 6-pin multipoint connector
Max. distance 1000 m
Max. transfer rate
Bus length ≤25 m 1 Mbit/s
Bus length ≤60 m 500 kbit/s
Bus length ≤200 m 250 kbit/s
Bus length ≤1000 m 50 kbit/s
Terminating resistor Hardware revision ≥ G0: Integrated, can be switched on using software
Hardware revision < G0: Must be wired externally
Interface IF9
Type RS485
Variant 3 pins of the 6-pin multipoint connector
Max. distance 1200 m
Transfer rate Max. 115.2 kbit/s
Terminating resistor Hardware revision ≥ G0: Integrated, can be switched on using software
Hardware revision < G0: Must be wired externally
Electrical properties
Nominal voltage 24 VDC -15% / +20%
Max. power consumption 15 W
Reverse polarity protection Yes
Electrical isolation IF1, IF2 and IF5 with each other, with other interfaces and with the base device
Operating conditions
Permissible mounting orientations
Standard mounting orientation Vertical
Tilt ±25°
Rotation In 90° increments (portrait/landscape)
Installation elevation above sea level
0 to 2000 m No limitation
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 Front: IP65, Back: IP20
Degree of protection per UL 50 Front: Type 4X indoor use only
Ambient conditions
Temperature
Operation 0 to 50°C
Storage -20 to 70°C
Transport -20 to 70°C
Relative humidity See temperature/humidity diagram.
Mechanical properties
Note Order terminal blocks 1x 0TB5104.2110-01, 1x 0TB5106.2110-01, 1x 0TB6102.2010-01 and 1x 0TB6102.2110-01 separately
Front
Design Anthracite gray pinstripe
Dimensions
Width 197 mm
Height 140 mm
Depth 51 mm
Weight 0.65 kg
Артикул:
4PPC70.0702-23B
Описание:
Power Panel C70, 7.0", landscape format, fieldbus interfaces: 1x CAN bus, 1x RS485. CPU and memory: Intel Atom 333 MHz (compatible), 256 MB DDRAM, 32 kB FRAM, 2 GB onboard flash drive. Display and touch screen: 7.0", 800 x 480 (WVGA) resolution, analog resistive touch screen, landscape format, anthracite gray pinstripe. Interfaces: 1x POWERLINK, 1x Ethernet 10/100 Mbit/s, 1x X2X Link, 2x USB 2.0, 1x CAN bus, 1x RS485.
Дополнительная информация:

B&R Panel Designer

Необходимые аксессуары
Terminal blocks
0TB5104.2110-01 Accessory terminal block, 4-pin (2.5), cage clamp, 0.5 mm²
0TB5106.2110-01 Accessory terminal block, 6-pin (2.5), cage clamp terminal block 0.5 mm²
0TB6102.2110-01 Принадлежность, 2-контактная клеммная колодка (3,81) с пружинными зажимами 1,5 мм²
Дополнительные аксессуары
Accessories
9A0013.01 Stylus pen for resistive touch screen
Other
6ACCRPP1.0000-000 Installation kit for Power Panel T-Series and C-Series variants: 6x retaining clips (orange), 1x 2-pin cage clamp terminal block, 1x 2-pin screw clamp terminal block. See the accessories of the Power Panel variant in the corresponding data sheet or on the website.
Terminal blocks
0TB6102.2010-01 Принадлежность, 2-контактная клеммная колодка (3,81) с винтовыми зажимами 1,5 мм²
USB accessories
5MMUSB.2048-01 Флеш-накопитель USB 2.0, 2048 МБ, B&R
5MMUSB.4096-01 Флеш-накопитель USB 2.0, 4096 МБ, B&R
E-CAD (Шаблоны Electro или EPLAN) Version (Date) Download
Panel EPLAN P8 from V2.4 EXE / 134 MB
M-CAD (Механические шаблоны) Version (Date) Download
3D File DXF/STEP C70 7.0" landscape ZIP / 6 MB
Документация Version (Date) Download
Power Panel C70 User's Manual PDF / 4 MB
Обновления Automation Studio HW Version (Date) Download
V4.1 HW Upgrade (4PPC70.0702-23B) EXE / 931 KB
Сертификаты Version (Date) Download
E115267 UL CoC Power Panel C70, T30 Series PDF / 336 KB

Выберите регион и язык:

B&R Logo