Please choose country and language

V4.3 HW Upgrade (8I76xxxxxxx.0P-xxx)

DWL@DWL10000585982

Version Language
Operating System
Date
Size
Type Download
2.3.0.0 * 08/12/2020 18 MB EXE AS4_HW_8I76xxxxxxx.0P-xxx.exe
Description V4.3 HW Upgrade (8I76xxxxxxx.0P-xxx)

Revision information 8I76xxxxxxx.0P-xxx

Version 2.3.0.0:

ID: 698060
Starting procedure (occasional ILF-error) revised with support for the new hardware variant 2
On few devices, several powercycles or reboots could lead to an ILF-error, which then has to be acknowledged by another powercycle. This behavoir was changed(better timings between inverter and option card) so that no ILF-error occurson powerup.
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 698250
Support forautomatic DNA configuration from AS 4.9.1
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\62042_1.fw(160), 1\62042_2.fw(160)

Version 2.2.0.1:

ID: 619895
Support for mappMotion
Support for mappMotion (from version 5.8)
The usage of the onboard POWERLINK interfaces on ARM CPUs (e.g. X20CP04xx) for mappMotion is restricted to the following minimun versions of AutomationRuntime;
M4.34, F4.45, C4.53, C4.63, A4.72
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No

ID: 657100
List of monitoring data points extended
Thelist of optional monitoring data points was extended to enable access tounfiltered values (SRFR, SOTR, SLCR, SOPR, SULN)
Channel description changed:Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\62042_1.fw(110)

Version 1.1.0.5:

ID: 637255
POWERLINK communication revised
Ongoing product improvements
- Ring redundancy: Cannot address the CN that closes the ring
- Optimization of hubbehavior
- Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors
- DNA: BC as head-end station switching hub off again
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 637535 / Support ID: 400282877
Download of Parameter "OPL" revised
The parameter "OPL" can be used to activate/deactivate the supervision "output phase loss".
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 638525
Configuration view extended and corrected
Configuration view revised
Access: Configuration parameter RSF added
Intermediate circuit: Configuration parameter DCCM always visible
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 638655
List of monitoring data points extended
The list of optional monitoring data points was extended by data point SMSS(status of safety function "Safe Maximum Speed")
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No

ID: 638665
ERROR CORRECTION
The following optional monitoring data points had to be renamed: 1. GDLS, 2. ETAD(unpacked). In consequence of double naming of the optional input data points, a malicious behavior of AutomationStudio can occur. After switching to the upgrade version, the links of the affected data points have to be checked and if necessary restored.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 638685
Download of motor data for synchronous motors enabled
Bug eliminated which avoided the download of motordata for synchronous motors.
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 639625
Behavior of 7 segment display adapted
After downloading the parameter set of the ACOPOSinverter, the display switches to the actual state of the drive.
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 642740
Download of the "I²t" motor temperature model revised
The parameters of the "I²t" motor temperature model (ITH, MTM, THT) can be downloaded as shown in the configuration view.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 645290
Maximum speed definition revised
The "TFR [Hz]" does not need to be configured anymore if the "rpm" reference model is used. The valid maximum speed of the axis is defined exclusively byparameter "SMA [rpm]".
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 649485
Module documentation revised
User manual V 1.20
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\62042_1.fw(110)

Version 1.0.2.0:

ID: 631640
Support ACOPOSinverter P76-P
Support for AutomationStudio
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes

ID: 633575
General inputtemplate - BLC revised
The sub function PES "external weight measurement" was unlock in the general input template "BLC function: Brake control (ASM)". It can be used for dynamic braking on vertical load movement scenarios.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No
Firmware: 1\62042_1.fw(101)
Version Language
Operating System
Date
Size
Type Download
2.2.0.1 * 09/30/2019 18 MB EXE AS4_HW_8I76xxxxxxx.0P-xxx.exe
Description V4.3 HW Upgrade (8I76xxxxxxx.0P-xxx)

Revision information 8I76xxxxxxx.0P-xxx

Version 2.2.0.1:

ID: 619895
Support for mappMotion
Support for mappMotion (from version 5.8)
The usage of the onboard POWERLINK interfaces on ARM CPUs (e.g. X20CP04xx) for mappMotion is restricted to the following minimun versions of AutomationRuntime;
M4.34, F4.45, C4.53,C4.63, A4.72
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No

ID: 657100
List of monitoring data points extended
The list of optional monitoring data points was extended to enable access to unfiltered values (SRFR, SOTR, SLCR, SOPR, SULN)
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\62042_1.fw(110)

Version 1.1.0.5:

ID: 637255
POWERLINK communication revised
Ongoing product improvements
- Ring redundancy: Cannot address the CN that closes the ring
- Optimization of hub behavior
- Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors
- DNA: BC as head-end station switching hub off again
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 637535 / Support ID: 400282877
Download of Parameter "OPL" revised
The parameter "OPL" can be used to activate/deactivate the supervision "output phase loss".
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 638525
Configurationview extended and corrected
Configuration view revised
Access: Configuration parameter RSF added
Intermediate circuit: Configuration parameter DCCM always visible
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 638655
List of monitoring data points extended
The list of optional monitoring data points was extended by data point SMSS(status of safety function "Safe MaximumSpeed")
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No

ID: 638665
ERROR CORRECTION
The following optional monitoring data points had to be renamed: 1. GDLS, 2. ETAD(unpacked). In consequence of double naming of the optional input data points, a malicious behavior of AutomationStudio can occur. After switching to the upgrade version, the links of the affected data points have to be checked and if necessary restored.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 638685
Download of motor data for synchronous motors enabled
Bug eliminated which avoided the download of motor data for synchronous motors.
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 639625
Behavior of 7 segment display adapted
After downloading the parameter set of the ACOPOSinverter, the display switches to the actual state of the drive.
Channel description changed:No
Configuration description changed: No
Firmware changed: No

ID: 642740
Download of the "I²t" motor temperature model revised
The parameters of the "I²t" motor temperature model (ITH, MTM, THT) can be downloaded as shown in the configuration view.
Channel description changed:Yes
Configuration description changed: No
Firmware changed: No

ID: 645290
Maximum speed definition revised
The "TFR [Hz]" doesnot need to be configured anymore if the "rpm" referencemodel is used. The valid maximum speed of the axis is defined exclusively by parameter "SMA [rpm]".
Channel description changed: No
Configuration description changed:Yes
Firmware changed: No

ID: 649485
Module documentation revised
User manual V 1.20
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\62042_1.fw(110)

Version 1.0.2.0:

ID: 631640
Support ACOPOSinverter P76-P
Support for AutomationStudio
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes

ID: 633575
General input template - BLC revised
The sub function PES "external weight measurement" was unlock in the general input template "BLC function: Brake control (ASM)". It can be used for dynamic braking onvertical load movement scenarios.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No
Firmware:1\62042_1.fw(101)
Version Language
Operating System
Date
Size
Type Download
1.1.0.5 * 06/19/2019 18 MB EXE AS4_HW_8I76xxxxxxx.0P-xxx.exe
Description V4.3 HW Upgrade (8I76xxxxxxx.0P-xxx)

Revision information 8I76xxxxxxx.0P-xxx

Version 1.1.0.5:

ID: 637255
POWERLINK communication revised
Ongoing product improvements
- Ring redundancy: Cannot address the CN that closes the ring
- Optimization of hub behavior
- Shortened preamble of Ethernet frame leading to incorrectly detected CRC errors
- DNA: BC as head-end station switching hub off again
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 637535 / Support ID: 400282877
Download of Parameter "OPL"revised
The parameter "OPL" can be used to activate/deactivate the supervision "output phase loss".
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 638525
Configuration view extended and corrected
Configuration view revised
Access: Configuration parameter RSF added
Intermediate circuit: Configuration parameter DCCM always visible
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 638655
List of monitoring data points extended
The list of optional monitoring data points was extended by data point SMSS(status of safety function "Safe Maximum Speed")
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No

ID: 638665
ERROR CORRECTION
The following optional monitoring data points had to be renamed: 1. GDLS, 2. ETAD(unpacked). In consequence of double naming of the optional input data points, a malicious behavior of AutomationStudio can occur. After switching to the upgrade version, the links of the affected data points have to be checked and if necessary restored.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 638685
Download of motor data for synchronous motors enabled
Bug eliminated which avoided the download of motor data for synchronous motors.
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 639625
Behavior of 7 segment display adapted
After downloading the parameter set of the ACOPOSinverter, the display switches to the actual state of the drive.
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 642740
Download of the "I²t" motor temperature model revised
The parameters of the "I²t" motor temperature model (ITH, MTM, THT) can be downloaded as shown in the configuration view.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 645290
Maximum speed definition revised
The"TFR [Hz]" does not need to be configured anymore if the "rpm" referencemodel is used. The valid maximum speed of the axis is defined exclusively by parameter "SMA [rpm]".
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 649485
Moduledocumentation revised
User manual V 1.20
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\62042_1.fw(110)

Version 1.0.2.0:

ID: 631640
Support ACOPOSinverter P76-P
Support for AutomationStudio
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes

ID: 633575
General input template - BLC revised
The sub function PES "external weight measurement" was unlock in the general input template "BLC function: Brake control (ASM)". It can be used for dynamic braking on vertical load movement scenarios.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No
Firmware: 1\62042_1.fw(101)
Version Language
Operating System
Date
Size
Type Download
1.0.2.0 * 02/18/2019 17 MB EXE AS4_HW_8I76xxxxxxx.0P-xxx.exe
Description V4.3 HW Upgrade (8I76xxxxxxx.0P-xxx)

Revision information 8I76xxxxxxx.0P-xxx

Version 1.0.2.0:

ID: 631640
Support ACOPOSinverterP76-P
Support for AutomationStudio
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes

ID: 633575
General input template - BLC revised
The sub function PES "external weight measurement" was unlock in the general input template "BLC function: Brake control (ASM)". It can be used for dynamic braking on vertical load movement scenarios.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No
Firmware: 1\62042_1.fw(101)
Back to list

Please choose country and language

B&R Logo

Please choose country

B&R Logo