Please choose country and language

V4.0 HW Upgrade (8I64xxxxxxx.00x-1)

DWL@DWL10000637996

Version Language
Operating System
Date
Size
Type Download
2.1.0.0 * 06/10/2020 12 MB EXE AS4_HW_8I64xxxxxxx.00x-1.exe
Description V4.0 HW Upgrade (8I64xxxxxxx.00x-1)

Revision information 8I64xxxxxxx.00x-1

Version 2.1.0.0:

ID: 686360 / Support ID: 400319099, 400319667
Setpoint selection in Hz (LFR/RFR) reworked
The setpoint selection was reworked and it is now possible to input Hz and RPM values (Hz-Setpoint: LFR/RFR RPM-Setpoint: LFRD/RFRD)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 688575 / Support ID: 400321231
Data point StatusDigitalOutput01 revised(ACPi P64new)
The status data point was used to display detected errors on the original product ACPi X64. The base product of the replacement ACPi P64new does not provide a similar error detection. Hence, all links for this bit have been removedfor the ACPi P64new (This change does not have any effict onusing an ACPi X64.)
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\45284_10.fw(114), 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 2.0.0.0:

ID:588475 / Support ID: 400248602
Datapoint CMI revised
Bit 1 (data point CMI) cannot be used via I/O mapping. The data point was eliminated from the I/O mapping.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 632215
Support for revised hardware variante
The ACOPOSinverter P64new is released as newhardware variant for the discontinued ACOPOSinverter X64.
The ACPOSinverter P64new supports all essential functions that have been available for the ACOPOSinverter X64. Further details about the deviations are collected in the migration document, which is added to the revised user manual.
Channel description changed: No
Configuration description changed: Yes
Firmware changed: Yes

ID: 679665
Data point ACPi_ModuleID revised
Theoptional data point ACPi_ModuleID can be managed as UINT (instead of an UDINT) on the I/O mapping. This optimizes the communication behavior (cyclic part of X2X).
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\45284_10.fw(114), 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 1.3.9.1:

ID: 515925
Internal revision
File history corrected
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 1.3.9.0:

ID: 466740
Function models renamed
no influence to technical behavior
Functions model "default" renamed to "Direct control"
Functions model "default (MotionConfiguration)" renamed to "ACP10SDC (MotionConfiguration)"
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 511480
Default values resored
Default parameter value for module supervision restored, in order to avoidproblems during conversion of existing projects in future.
ATTENTION: If module was stored in an Automation Studio project using hardware file 1.3.8.5, ensure parameter module supervision to have the desired value after upgrading.

INFORMATION:
The demaged file V 1.3.8.5 was delivered by AutomationStudio 4.2.5 bis 4.2.6 (complete installation).
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No
Firmware: 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 1.3.8.5:

ID: 380420 / Support ID: 400132814
View in System Designer revised
Channel description changed: No
Configuration description changed: No
Firmware changed: No

ID: 511590
Motion Wizzard revised
In AS 4.x, the aged library "AsString" won’t be added to a AS project anymore. The "AsBrStr" will be used by the Motion instead.
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 1.3.8.1:

ID: 321155
General review of HW files
Missing texts/textparts in HW file for AS4.x restored.
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No

ID: 366700 / Support ID: 400126199
Using ACPi X64 with SGC-CPU in AS4
Adaption for Automation Studio 4; Configuration parameters can be download,when ACPi is used with SGC cpu.
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 1.3.8.0:

ID: 329805
Change filter settings at Counter02
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 1.3.6.0:

ID: 300120
Configuration Download parameters "on change" added
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\45284_2.fw(10), 1\45284_3.fw(10)

Version 1.3.5.0:

ID: 276485 / Support ID: 400074496
Timeout of AsIOAccRead() on ACPi X64
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes

ID: 291675
With the configuration "Download parameters = no" all inverter configurations will be retained now.
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\45284_2.fw(9), 1\45284_3.fw(9)

Version 1.3.4.0:

ID: 276790 / Support ID: 400077929
Inverter configuration optimized
Channel description changed: No
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\45284_2.fw(8), 1\45284_3.fw(8)

Version 1.3.3.0:

ID: 274200
After installation of Upgrade 1.3.2.0 RevInfo appears two times in help
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\45284_2.fw(8), 1\45284_3.fw(8)

Version 1.3.2.0:

ID: 270825 / Support ID: 400074141
At startup a COF error could appear with version 1.3.1.0
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\45284_2.fw(7), 1\45284_3.fw(7)

Version 1.3.1.0:

ID: 258760 / Support ID: 400065557
On 8I0IF109.200-1 with rev. B5 the relay does not work in standalone mode
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\45284_2.fw(5), 1\45284_3.fw(5)

Version 1.2.0.0:

ID: 246470 / Support ID: 400057134
The boottime of X64 takes 8-45 seconds
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: Yes
Firmware: 1\45284_2.fw(5), 1\45284_3.fw(5)

Version 1.1.0.2:

ID: 245955
Customer-specific expansion of hardware description file
This upgrade has no impact on the Automation Studio and the standard version of the FieldbusDESIGNER
Channel descriptionchanged: No
Configuration description changed: No
Firmware changed:No
Firmware: 1\45284_2.fw(4)

Version 1.0.5.0:

ID: 238280/ Support ID: 400049786 400049841 400050585 400051602 400052158 400054894
At startup a CFF error could appear
Channel description changed: No
Configuration description changed: No
Firmware changed: Yes
Firmware: 1\45284_2.fw(4), 1\45284_3.fw(4)

Version 1.0.0.0:

ID: 223865
Support for ACOPOSInverter X64
Channel description changed: No
Configuration description changed: No
Firmware changed: No
Firmware: 1\45284_2.fw(2)
Version Language
Operating System
Date
Size
Type Download
2.0.0.0 * 03/05/2020 12 MB EXE AS4_HW_8I64xxxxxxx.00x-1.exe
Description V4.0 HW Upgrade (8I64xxxxxxx.00x-1)

Revision information 8I64xxxxxxx.00x-1

Version 2.0.0.0:

ID: 588475 / Support ID: 400248602
Datapoint CMI revised
Bit 1 (data point CMI) cannot be used via I/O mapping. The data point was eliminated from the I/O mapping.
Channel description changed: Yes
Configuration description changed: No
Firmware changed: No

ID: 632215
Support for revised hardware variante
TheACOPOSinverter P64new is released as new hardware variant for the discontinued ACOPOSinverter X64.
The ACPOSinverter P64new supports all essential functions that have been available for the ACOPOSinverter X64. Further details about the deviations are collected in the migration document, which is added to the revised user manual.
Channel description changed: No
Configurationdescription changed: Yes
Firmware changed: Yes

ID: 679665
Data point ACPi_ModuleID revised
The optional data point ACPi_ModuleID can be managed as UINT (instead of anUDINT) on the I/O mapping. This optimizes the communication behavior (cyclic part of X2X).
Channel description changed: Yes
Configuration description changed: Yes
Firmware changed: No
Firmware: 1\45284_10.fw(113), 1\45284_2.fw(10), 1\45284_3.fw(10)
Back to list

Please choose country and language

B&R Logo

Please choose country

B&R Logo