Kies land en taal alstublieft

Short description
I/O module 1 AB incremental encoder, 24 V, 4 digital inputs, 4 channels configurable as inputs or outputs
General information
Input voltage 24 VDC -15 % / +20 %
B&R ID code 0x21EF
Status indicators I/O function per channel, operating state, module status
Module run/error Yes, using status LED and software
Outputs Yes, using the status LED and software (output error status)
Power consumption
Bus 0.01 W
Internal I/O 1.5 W
Additional power dissipation caused by actuators (resistive) [W] -
Type of signal lines Shielded cables must be used for all signal lines.
CE Yes
ATEX Zone 2, II 3G Ex nA nC IIA T5 Gc
IP20, Ta (see X20 user's manual)
FTZÚ 09 ATEX 0083X
UL cULus E115267
Industrial control equipment
HazLoc cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5
KC Yes
Digital inputs
Quantity 4 + 4 additional channels, configurable as inputs or outputs
Nominal voltage 24 VDC
Input voltage 24 VDC -15 % / +20 %
Input current at 24 VDC Approx. 1.3 mA
Input circuit Sink
Input filter
Hardware ≤2 μs
Software -
Connection type 1-wire connections
Input resistance 18.4 kΩ
Switching threshold
Low <5 VDC
High >15 VDC
Isolation voltage between channel and bus 500 Veff
AB incremental encoder
Quantity 1
Encoder inputs 24 V, asymmetrical
Counter size 32-bit
Input frequency Max. 100 kHz
Evaluation 4x
Encoder power supply Module-internal, max. 600 mA
Overload characteristics of encoder power supply Short circuit protection, overload protection
Digital outputs
Quantity Up to 4, configurable as inputs or outputs using software
Variant Push / Pull / Push-Pull
Nominal voltage 24 VDC
Switching voltage 24 VDC -15 % / +20 %
Nominal output current 0.1 A
Total nominal current 0.4 A
Connection type 1-wire connections
Output circuit Sink or source
Output protection Thermal cutoff if overcurrent or short circuit occurs, integrated protection for switching inductances
Actuator power supply Module-internal, max. 600 mA
Diagnostic status Output monitoring
Leakage current when the power is switched off Max. 25 µA
Residual voltage <0.9 V at 0.1 A rated current
Peak short-circuit current <10 A
Switch-on in the event of overload shutdown or short-circuit shutdown Approx. 10 ms (depends on the module temperature)
Switching delay
0 → 1 <2 µs
1 → 0 <2 µs
Switching frequency
Resistive load Max. 24 kHz
Inductive load See section "Switching inductive loads" (at 90% duty cycle).
Braking voltage when switching off inductive loads Switching voltage + 0.6 VDC
Isolation voltage between channel and bus 500 Veff
Electrical properties
Electrical isolation
Channel isolated from bus

Channel not isolated from channel
Operating conditions
Mounting orientation
Horizontal Yes
Vertical Yes
Installation elevation above sea level
0 to 2000 m No limitations
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP20
Ambient conditions
Horizontal mounting orientation -25 to 60°C
Vertical mounting orientation -25 to 50°C
Derating -
Storage -40 to 85°C
Transport -40 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Mechanical properties
Note Order 1x X20TB12 terminal block separately
Order 1x X20BM11 bus module separately
Pitch 12.5+0.2 mm
Materiaal nummer:
  • Command-dependent digital pattern output
  • Counter-dependent output circuit
  • Event-controlled abort criteria
  • 4 digital inputs
  • 4 digital channels, configurable as inputs or outputs

The module can be used to configure and carry out simple movements. For this purpose, the module has one AB encoder input and a total of 8 digital channels. Four of them are inputs, and the other 4 can be set as either an input or an output. Various output bit patterns are stored directly in the module.

The module is perfectly suited for easy to create drive control tasks for program and event controlled motor movements. Feed movements using drives with 2 speeds and forward/reverse movement are created easily and efficiently.

Verplichte accessoires
Bus modules
X20BM11 X20 bus module, 24 VDC keyed, internal I/O supply continuous
X20BM15 X20 bus module, with node number switch, 24 VDC keyed, internal I/O supply continuous
Terminal blocks
X20TB12 X20 terminal block, 12-pin, 24 VDC keyed
Automation Studio HW Upgrades Versie (datum) Download
V2.6 HW Upgrade (X20CM1201) EXE / 1 MB
V3.0 HW Upgrade (X20CM1201) EXE / 2 MB
V4.0 HW Upgrade (X20CM1201) EXE / 967 KB
Certificaten Versie (datum) Download
244665 CSA HazLoc Certificate of Compliance X20, X67 PDF / 56 KB
E115267 UL CoC X20 PDF / 847 KB
FTZU 09 ATEX 0083X PDF / 697 KB
Documentatie Versie (datum) Download
Data sheet X20CM1201 PDF / 364 KB
X20 System User´s Manual PDF / 56 MB
E-CAD (Electro of EPLAN Templates) Versie (datum) Download
X20 EPLAN P8 from V2.4 EXE / 161 MB
M-CAD (Mechan. Templates) Versie (datum) Download
3D File DXF/STEP X20 Electronic module ZIP / 10 KB
3D File STEP X20 I/O-Slice ZIP / 872 KB
Dimensions PDF X20 Electronic module PDF / 3 KB

Kies land en taal alstublieft

B&R Logo