• Website
  • Model Number
  • Serial number
Logged in as UsernameLogout
B&R Logo
  • Specifications

  • Basic Information

  • Accessories

  • Downloads

  • Revisions

  • Serial number

    Status displayGreen LED (DC OK), threshold value Uout = 21.5 V
    Isolation voltages
    Input - Output4 kV AC (type test)
    2 kV AC (routine test)
    Input - PE3.5 kV AC (type test)
    2 kV AC (routine test)
    Output - PE500 VDC (type test)
    Connection typeScrew clamp connection
    Connection cross section
    Wire end sleevesFlexible cables require wire end sleeves in order to fulfill EN 60950 / UL 60950
    Flexible0.2 to 2.5 mm² / 24 to 12 AWG
    Inflexible0.2 to 2.5 mm² / 24 to 12 AWG
    Wire stripping length6.5 mm (input/output)
    ULcULus E123528
    Industrial control equipment
    Nominal input voltage100 to 240 VAC
    Input voltageAC 85 to 264 V (wide range), 45 to 65 Hz
    DC 95 to 250 V
    Input currentApprox. 0.8 A (120 VAC)
    Approx. 0.4 A (230 VAC)
    Inrush current limitation<15 A (typical)
    I2t<0.6 A2s
    Power failure bypass>20 ms (120 VAC)
    >100 ms (230 VAC)
    Switch-on time<0.5 s
    Power factor (cos φ)0.65
    Protective circuitTransient surge protection (varistor)
    Internal fuse3.15 A, slow-blow
    Required line fuse for line protection6 A (characteristic B)
    10 A (characteristic B)
    16 A (characteristic B)
    Nominal voltage24 VDC ±1%
    Output power60 W
    Setting range for output voltage22.5 to 29.5 VDC (>24 VDC power constant)
    Output current
    -25 to 40°C2.75 A
    40 to 55°C2.5 A
    >55°CDerating: 2.5% per °C
    Current limitationMax. 4.4 A
    Control deviation<1% (static load change 10 to 90%)
    <2% (dynamic load change 10 to 90%)
    <0.1% (input voltage change ±10%)
    Rise time<0.5 s (UOUT (10 to 90%))
    Residual ripple<50 mVSS (at rated values)
    Switching peaks<50 mVSS (at rated values)
    Can be connected in parallelYes, to establish redundancy and increase capacity
    Can be connected in seriesYes
    Protection against internal overvoltagesYes, limited to approximately 35 VDC
    Protection functionsOutput protected against continuous short circuit, open circuit and overload
    Power back immunityMax. 35 VDC
    Output noise suppressionUnit complies with EN 55011 (Class B)
    Efficiency>86% (at 230 VAC and rated values)
    MTBF>500,000 h, in accordance with IEC 61709 (SN 29500)
    Power dissipation
    Rated loadMax. 9.9 W
    No-load operationMax. 0.7 W
    Ventilation/CoolingNormal convection, no fan required
    Degree of protection per EN 60529IP20
    Rated protectionII
    Operation-25 to 70°C (>55°C derating)
    Storage-40 to 85°C
    Transport-40 to 85°C
    Relative humidity
    OperationMax. 95%, non-condensing
    Operation<15 Hz, amplitude ±2.5 mm, in accordance with IEC 60068-2-6
    15 to 150 Hz, 2.3 g, 90 min
    Operation30 g in each direction, in accordance with IEC 60068-2-27
    Pollution degree2, in accordance with EN 50178
    Climate category3K3, in accordance with EN 60721
    Mounting foot: POM plastic
    InstallationEasy rail mounting (DIN rail NS 35, EN 60715) or wall mounting
    Width72 mm
    Height90 mm
    Depth61 mm
    Weight300 g


  • 100 to 240 VAC wide-range input
  • Can be connected in parallel for increased capacity and redundancy
  • Reliable operation due to long power failure bypass function under full load and high MTBF (>500,000 h)
  • International certification package
  • Wide temperature range from -25 to 70°C
  • Extra flat design
  • Easy DIN rail or wall mounting
Product description:
Material number:
24 VDC power supply, 1 phase, 2.5 A, input 100 to 240 VAC, wide range, top-hat rail installation
toggle all
This site uses cookies to enable a better customer experience. By continuing to browse the site you are agreeing to our use of cookies. Please find more information about cookies in our Privacy Policy.