Please choose country and language

Short description
I/O module X90 mobile 4-channel analog input module for vibration measurement and analysis for condition monitoring
General information
Nominal voltage 9 to 32 VDC
B&R ID code 0xEF81
Power consumption 1.59 W
Electrical isolation
Channel - Channel No
Channel - I/O power supply No
Certifications
UN ECE-R10 Yes
CE Yes
Functional safety Not relevant
Analog inputs
Quantity 4
Input type IEPE sensor: Acceleration
Accuracy (analog input signal) at 25°C
Offset (based on 20 V measurement range) ±0.2%
Gain with sine signal where f = 100 Hz ±1%
Temperature drift (analog input signal)
Max. offset drift (based on 20 V measurement range) ±0.005 %/°C
Max. gain drift with sine signal where f = 100 Hz ±0.020 %/°C
Accuracy of frequency response (1 Hz to 10 kHz) ±5%
Digital converter resolution 24-bit
Short-circuit proof Yes
Open-circuit detection
Per channel Yes
Threshold voltage, typical Starting at 21.3 V (or greater) for more than 1 ms
Input voltage range
Common-mode voltage (UCM) -1 to 17 V
Differential voltage (UD) UCM ≤ 7 V: ±10 V
UCM > 7 V: ±(17 V - UCM)
Conversion procedure Sigma-delta
Crosstalk between channels ≤-70 dB
Type Vibration input
Sampling frequency 51.5625 kHz
Input high pass cutoff frequency 36 mHz
Input low pass cutoff frequency 20 kHz
Downsampling 200 Hz, 500 Hz, 1 kHz, 2 kHz, 5 kHz, 10 kHz (configurable)
Frequency resolution of spectra 0.0629 Hz, 0.1574 Hz, 0.3147 Hz, 0.6294 Hz, 1.5736 Hz, 3.1471 Hz
Sensor power supply IEPE, 5 mA constant current source (4.9 - 5.5 mA), can be switched off for each channel
Operating conditions
Mounting orientation
Any Yes
Degree of protection per EN 60529 IP69K
Ambient conditions
Temperature
Operation
Storage -40 to 85°C
Transport -40 to 85°C
Relative humidity
Operation 5 to 100%, condensing
Storage 5 to 100%, condensing
Transport 5 to 100%, condensing
Mechanical properties
Dimensions
Width 47 mm
Length 95 mm
Material number:
X90CM480.04-00
Description:
X90 mobile condition monitoring, option board for vibration measurement and vibration analysis of condition monitoring tasks, 4 IEPE analog inputs
Optional Accessories
Sensor cable
0ACC0020.01-1 Cable for accelerometer, length 2 m 2x 0.34 mm², female M12 connector on the sensor side, can be used in cable drag chains, UL listed
0ACC0050.01-1 Cable for accelerometer, length 5 m 2x 0.34 mm² female M12 connector on the sensor side, can be used in cable drag chains, UL listed
0ACC0100.01-1 Cable for accelerometer, length 10 m 2x 0.34 mm², female M12 connector on the sensor side, can be used in cable drag chains, UL listed
0ACC0150.01-1 Cable for accelerometer, length 15 m 2x 0.34 mm², female M12 connector on the sensor side, can be used in cable drag chains, UL listed
0ACC0200.01-1 Cable for accelerometer, length 20 m 2x 0.34 mm², female M12 connector on the sensor side, can be used in cable drag chains, UL listed
0ACC0500.01-1 Cable for accelerometer, length 50 m 2x 0.34 mm², female M12 connector on the sensor side, can be used in cable drag chains, UL listed
0ACC1000.01-1 Cable for accelerometer, length 100 m 2x 0.34 mm², female M12 connector on the sensor side, can be used in cable drag chains, UL listed
Sensors
0ACS100A.00-1 Accelerometer, nominal sensitivity 100 mV/g, top exit
0ACS100A.90-1 Accelerometer, nominal sensitivity 100 mV/g, side exit
Automation Studio HW Upgrades Version (Date) Download
V4.3 HW Upgrade (X90CM480.04-00) EXE / 13 MB
Certificates Version (Date) Download
UN ECE-R10 PDF / 173 KB
Documentation Version (Date) Download
Datasheet X90CM480.04-00 PDF / 20 MB
X90 mobile System User´s Manual PDF / 9 MB

Please choose country and language

B&R Logo