- Product IDGeneral informationModule typeACOPOSmotor moduleMaximum current load of 19-pin hybrid connectorPower contactsMax. 20 A at 40°CCertificationCEYescULusYes 1)FSCYes 1)SupportSoftwareACP10V2.422 or higherThermal characteristicsMethods of cooling in accordance with EN 60034-6 (IC code)StandardSelf-cooled; no separate surface cooling (IC4A0A0)With 8ZBDF fan kit installedExternally-cooled; surface cooling with independent cooling module attached (IC4A0A6)Insulation class in accordance with EN 60034-1FThermal motor protection in accordance with EN 60034-11Maximum winding temperature 155°C (limited to 140°C using software)Operating conditionsConstruction and mounting arrangement type in accordance with EN 60034-7 (IM code)horizontal (IM3001); vertical, motor hangs on the machine (IM3011); vertical, motor stands on the machine (IM3031)Reduction of the nominal current and stall current at installation altitudes over 500 m above sea level10% per 1000 mReduction of the continuous power at installation altitudes over 500 m above sea level10% per 1000 mInstallation at elevations above sea levelNominal0 to 500 mMaximum 2)4000 mDegree of pollution in accordance with EN 60664-12 (non-conductive pollution)Overvoltage category in accordance with IEC 60364-4-443:1999IIIEN 60529 protection 3)Without optional oil seal: IP64
With optional oil seal: IP65
With 8ZDFB fan kit installed: IP24Environmental conditionsTemperatureOperationNominal5 to 40°CMaximum55°C 4)Storage-25 to 55°CTransport-25 to 70°CMax. flange temperature65°CRelative humidityOperation5 to 85%, non-condensingStorage5 to 95%, non-condensingTransportMax. 95% at 40°CMechanical characteristicsMotor paintWater-based paint, RAL 2005 flatInverter paintElectrophoretic deposition (EPD), blackVibration severity in accordance with EN 60034-14Vibration severity grade A 5)Roller bearing, dynamic load ratings and nominal service lifeBased on DIN ISO 281Shaft end in accordance with DIN 748Form EOil seal in accordance with DIN 3760Form AKey and keyway in accordance with DIN 6885-1Keyway form N1; key form ABalancing the shaft in accordance with DIN ISO 8821Half-key arrangementMounting flange in accordance with DIN 42948Form ASmooth rotation of shaft end, coaxial properties and mounting flange plane in accordance with DIN 42955Tolerance RShort descriptionACPm65m UT 50 A
General technical data
- 1)Starting with revision C1.2)Continuous operation at altitudes ranging from 500 m to 4000 m above sea level is possible (taking the specified continuous current reductions into consideration). Requirements that go above and beyond this must be arranged with B&R.3)The specified level of protection is only in place if all connectors on the module that are not being used are closed with suitable caps or covers. Suitable caps and covers are available as optional accessories (X67AC0M08, X67AC0M12, 8CXC000.0000-00). The module is rated at IP20 when delivered.4)Continuous operation at ambient temperatures ranging from 40°C to max. 55°C is possible (taking the specified continuous current reductions into consideration), but this will result in a shorter service life.5)Vibration severity grade B on request.
- Product ID8DIcde.ffggg7i00-18DIcde.ffggg0i00-1DC bus connectionVoltageNominal750 VDCContinuous power consumption 1)(PN/0.97) + PIMDC bus capacitanceSize 3 (8DI3x): 10 µF
Size 4 (8DI4x): 15 µF
Size 5 (8DI5x): 24 µFDesign19-pin hybrid connector 2)Cable lengthMaximum30 m24 VDC power supplyInput voltage24 VDC +20% / -25%Input capacitance120 µFMax. power consumption10 W + PHoldingBrake + P24 VDC Out 1[0 ... 96 W] + P24 VDC Out 2[0 ... 12 W]Design19-pin hybrid connector 2)Cable lengthMaximum30 m24 VDC Out 1Output voltageDepends on the 24 VDC supply-Continuous currentMax. 4 A-Fuse protectionElectronic-Design24 VDCM8 connector-COMM8 connector-Cable lengthMaximum30 m24 VDC Out 2Output voltageDepends on the 24 VDC supply-Continuous currentMax. 0.5 A-Fuse protectionElectronic-Design24 VDCM12 connector-COMM12 connector-Cable lengthMaximum30 mMotor connectionNominal switching frequency5 kHzPossible switching frequencies 3)5 / 10 / 20 kHzMax. output frequency598 Hz 4)Motor holding brake connectionQuantity1Continuous current1 AMax. switching frequency0.5 HzResponse threshold for undervoltage monitoring24 VDC -25%FieldbusTypePOWERLINK V1/V2 100BASE-T (ANSI/IEE 802.3)DesignInternal 2-port hub, 2x 19-pin male hybrid connectorCable lengthMax. 100 m between two stations (segment length) 5)Transfer rate100 Mbit/sEnable inputsQuantity2WiringSinkElectrical isolationInput - Inverter moduleYesInput - InputYesInput voltageNominal24 VDCMaximum30 VDCInput current at nominal voltage80 mASwitching thresholdLow<5 VHigh>15 VSwitching delay at nominal input voltageEnable 1 → 0, PWM off12 msEnable 0 → 1, ready for PWM1 msModulation compared to ground potentialMax. ±38 VDesign19-pin hybrid connector 2)Trigger inputsQuantity2-WiringSink-Electrical isolationInput - Inverter moduleNo-Input - InputNo-Input voltageNominal24 VDC-Maximum30 VDC-Switching thresholdLow<5 V-High>15 V-Input current at nominal voltage5 mA-Switching delayRising edgeIn preparation-Falling edgeIn preparation-Modulation compared to ground potentialMax. ±38 V-DesignM12 connector-Cable lengthMaximum30 mSupportSoftwareACP10V2.43 and higherShort descriptionACPm65m OT Br PLK 24Vout TrACPm65m OT Br
8DIcde.ffggg7i00-1, 8DIcde.ffggg0i00-1 - Technical data
- 1)Valid in the following conditions: 750 VDC DC bus voltage, 5 kHz switching frequency, 40°C ambient temperature, installation elevation <500 m above sea level, no derating due to cooling type.2)It is important to note that the 19-pin hybrid connector is designed for max. 5 connection cycles.3)B&R recommends operating the module at its nominal switching frequency. Operating the module at a higher switching frequency for application-specific reasons reduces the continuous current and increases the CPU load.4)The module's electrical output frequency (SCTRL_SPEED_ACT * MOTOR_POLEPAIRS) is monitored to protect against dual use in accordance with Council Regulation (EC) 428/2009 | 3A225. If the electrical output frequency of the module exceeds the limit value of 598 Hz uninterrupted for more than 0.5 s, then the current movement is aborted and error 6060 is output ("Power unit: Limit speed exceeded").5)Limited to 30 m when using hybrid cables.