Please choose country and language

Short description
I/O module 4 digital input channels, 4 digital channels configurable as inputs or outputs, 1 universal counter pair (2 event counters, AB counter or up/down counter), linear movement generator (A/B, direction/frequency) with up to two reference pulses, SSI absolute encoder, relative or absolute moments of input edges with μs resolution, time-triggered I/O, I/O oversampling
General information
B&R ID code 0x2547
Status indicators I/O function per channel, operating state, module status
Diagnostics
Module run/error Yes, using LED status indicator and software
Outputs Yes, using LED status indicator
Power consumption
Bus 0.01 W
Internal I/O 1.5 W
Additional power dissipation caused by actuators (resistive) [W] -
Type of signal lines Shielded cables must be used for all signal lines.
Certifications
CE Yes
ATEX Zone 2, II 3G Ex nA nC IIA T5 Gc
IP20, Ta (see X20 user's manual)
FTZÚ 09 ATEX 0083X
UL cULus E115267
Industrial control equipment
HazLoc cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5
DNV GL Temperature: B (0 - 55°C)
Humidity: B (up to 100%)
Vibration: B (4 g)
EMC: B (bridge and open deck)
LR ENV1
KR Yes
ABS Yes
EAC Yes
KC Yes
Linear motion generator
Quantity 1
Encoder outputs 24 V, asymmetrical (A/B, direction/frequency)
Counter size 16/32-bit
Digital inputs
Quantity 4 + 4, configuration as input or output using software
Nominal voltage 24 VDC
Input voltage 24 VDC -15% / +20%
Input current at 24 VDC Approx. 1.3 mA
Input circuit Sink
Input filter
Hardware ≤2 µs
Software -
Input resistance 18.4 kΩ
Additional functions SSI absolute encoder, universal counter pair, latch function for universal counter pair
Input frequency 100 kHz
Switching threshold
Low <5 VDC
High >15 VDC
Overload characteristics of encoder power supply Short-circuit proof, overload-proof
Insulation voltage between channel and bus 500 Veff
SSI absolute encoder
Quantity 1
Counter size Up to 32-bit depending on encoder
Max. transfer rate 125 kbit/s
Encoder power supply Module-internal, max. 600 mA
Nominal voltage 24 V, asymmetrical
Universal counter pair
Quantity 1
Operating modes 2x event counter, up/down counter, AB counter
Encoder inputs 24 V, asymmetrical
Counter size 16/32-bit
Input frequency Max. 100 kHz
Evaluation
AB counter 4x
Event counters 2x
Up/Down counter 2x
Signal form Square wave pulse
Encoder power supply Module-internal, max. 600 mA
Digital outputs
Quantity Up to 4, configuration as input or output using software
Variant Push / Pull / Push-Pull
Nominal voltage 24 VDC
Switching voltage 24 VDC -15% / +20%
Nominal output current 0.1 A
Total nominal current 0.4 A
Output circuit Sink and/or source
Output protection Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads
Diagnostic status Output monitoring
Leakage current when the output is switched off Max. 25 µA
Residual voltage <0.9 V at 0.1 A nominal current
Peak short-circuit current <10 A
Switch-on in the event of overload shutdown or short-circuit shutdown Approx. 10 ms (depends on the module temperature)
Switching delay
0 → 1 <2 µs
1 → 0 <2 µs
Switching frequency
Resistive load Max. 125 kHz
Inductive load See section "Switching inductive loads".
Braking voltage when switching off inductive loads Switching voltage + 0.6 VDC
Additional functions Clock for SSI absolute encoder, linear movement generator
Electrical properties
Electrical isolation
Channel isolated from bus

Channel not isolated from channel
Operating conditions
Mounting orientation
Horizontal Yes
Vertical Yes
Installation elevation above sea level
0 to 2000 m No limitation
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Horizontal mounting orientation -25 to 60°C
Vertical mounting orientation -25 to 50°C
Derating -
Storage -40 to 85°C
Transport -40 to 85°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Mechanical properties
Note Order 1x terminal block X20TB12 separately.
Order 1x bus module X20BM11 separately.
Pitch 12.5 +0.2 mm
Produktové číslo:
X20DS1319
Popis:
  • 4 digital input channels
  • 4 digital channels, configurable as inputs or outputs
  • 1 universal counter pair (2 event counters, AB counters or up/down counters)
  • Linear movement generator (A/B, direction/frequency) with up to 2 reference pulses
  • SSI absolute encoder
  • NetTime timestamp: Input data, target position, position change, edge change, counter change

This module is a multifunction digital signal processor module. It can be used extremely flexibly for a wide variety of tasks involving digital signal processing or digital signal generation. Two primary example applications include controlling stepper output stages with pulse and direction signals or using as encoder emulation. In this application, for example, frequency inverters or servo axes with the speed follow function can follow a real or virtual master axis.

An additional essential feature is the module's integrated timestamp function. It allows counter ramps curves to be generated virtually independently of bus cycle times during encoder emulation, for example. Only the target counter value and moment when it should be reached are transferred. The module automatically generates the corresponding counter values at the appropriate time, precisely in microsecond resolution and independently of the bus clock.

Povinné příslušenství
Bus modules
X20BM11 X20 bus module, 24 VDC keyed, internal I/O supply continuous
X20BM15 X20 bus module, with node number switch, 24 VDC keyed, internal I/O supply continuous
Terminal blocks
X20TB12 X20 terminal block, 12-pin, 24 VDC keyed
Automation Studio HW Upgrades Verze (Datum) Stáhnout
V2.7 HW Upgrade (X20DS1319) EXE / 2 MB
V3.0 HW Upgrade (X20DS1319) EXE / 4 MB
Certifikáty Verze (Datum) Stáhnout
244665 CSA HazLoc Certificate of Compliance X20, X67 PDF / 56 KB
ABS Certificate of Product Design Assessment - X20 IO Series PDF / 2 MB
DNV GL Type Approval Certificate - X20 / Power Panel T30 PDF / 164 KB
E115267 UL CoC X20 PDF / 847 KB
FTZU 09 ATEX 0083X PDF / 697 KB
KR Type Approval Certificate MIL39390-AC003 (X20 System) PDF / 758 KB
Lloyds Register PDF / 506 KB
Safe cutoff of potential groups PDF / 735 KB
X20, X67 KC certificates PDF / 6 MB
Dokumentace Verze (Datum) Stáhnout
Data sheet X20DS1319 PDF / 832 KB
X20 System User´s Manual PDF / 56 MB
E-CAD (Electro or EPLAN Templates) Verze (Datum) Stáhnout
X20 EPLAN P8 from V2.4 EXE / 161 MB
M-CAD (Mechan. Templates) Verze (Datum) Stáhnout
3D File DXF/STEP X20 Electronic module ZIP / 10 KB
3D File STEP X20 I/O-Slice ZIP / 872 KB
Dimensions PDF X20 Electronic module PDF / 3 KB
Všeobecné Verze (Datum) Stáhnout
V4.0 HW Upgrade (X20DS1319) EXE / 2 MB

Please choose country and language

B&R Logo

Please choose country

B&R Logo