Please choose country and language

Short description
I/O module 2 analog inputs, 2 analog outputs, each 0 to 20 mA
General information
B&R ID code 0x1466
Status indicators I/O function for each channel, supply voltage, bus function
Diagnostics
Inputs Yes, using status LED and software
I/O power supply Yes, using status LED and software
Connection type
X2X Link M12, B-keyed
Inputs/Outputs 4x M12, A-keyed
I/O power supply M8, 4-pin
Power consumption
Internal I/O 3 W
X2X Link power supply 0.75 W
Certifications
CE Yes
ATEX Zone 2, II 3G Ex nA IIA T5 Gc
IP67, Ta = 0 - Max. 60°C
TÜV 05 ATEX 7201X
UL cULus E115267
Industrial control equipment
HazLoc cCSAus 244665
Process control equipment
for hazardous locations
Class I, Division 2, Groups ABCD, T5
EAC Yes
KC Yes
I/O power supply
Nominal voltage 24 VDC
Voltage range 18 to 30 VDC
Integrated protection Reverse polarity protection
Power consumption
Sensor/Actuator power supply Max. 12 W
Sensor/Actuator power supply
Voltage I/O power supply minus voltage drop for short circuit protection
Voltage drop for short-circuit protection at 0.5 A Max. 2 VDC
Summation current Max. 0.5 A
Short-circuit proof Yes
Analog inputs
Input 0 to 20 mA
Input type Differential input
Digital converter resolution 12-bit
Conversion time 400 µs for both inputs
Output format INT
Output format
Current INT 0x0000 - 0x7FFF / 1 LSB = 0x0010 = 4.883 µA
Load <300 Ω
Input protection Protection against wiring with supply voltage
Permissible input signal Max. ±30 V
Output of digital value during overload
Undershoot 0x0000
Overshoot 0x7FFF
Conversion procedure Successive approximation
Max. error
Gain 0.1%
Offset 0.05%
Max. gain drift 0.013 %/°C
Max. offset drift 0.02%/°C
Common-mode rejection
DC >50 dB
50 Hz >50 dB
Common-mode range ±11 V
Crosstalk between channels <-70 dB
Nonlinearity <0.1%
Insulation voltage between channel and bus 500 VEff
Input filter
Cutoff frequency 300 Hz
Slope 40 dB
Analog outputs
Output 0 to 20 mA
Digital converter resolution 12-bit
Conversion time 400 µs for both outputs
Settling time on output change over entire range Approx. 1 ms
Switch on/off behavior Internal enable relay for booting and errors
Output protection Protection against wiring with supply voltage, short circuit protection
Output format INT 0x0000 - 0x7FFF / 1 LSB = 0x0008 = 4.883 µA
Load per channel Max. load is 400 Ω
Output filter 1st-order low pass / cutoff frequency 1.5 kHz
Max. gain drift 0.015% / °C
Max. offset drift 0.032% / °C
Error caused by load change Max. 0.5%, from 1 Ω → 400 Ω, resistive
Nonlinearity <0.1%
Insulation voltage between channel and bus 500 VEff
Output response when the power supply is switched on/off An enable relay is switched on at a defined value ≠ 0, default setting = 10 kΩ to GND
Short-circuit proof
Current limiting ±40 mA
To GND Yes
To sensor or I/O power supply Yes
Max. error at 25°C and 50 Ω load
Gain 0.2%
Offset 0.05%
Electrical properties
Electrical isolation
Channel isolated from bus

Channel not isolated from channel
Operating conditions
Mounting orientation
Any Yes
Installation elevation above sea level
0 to 2000 m No limitations
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP67
Ambient conditions
Temperature
Operation -25 to 60°C
Derating -
Storage -40 to 85°C
Transport -40 to 85°C
Mechanical properties
Dimensions
Width 53 mm
Height 85 mm
Depth 42 mm
Weight 175 g
Torque for connections
M8 Max. 0.4 Nm
M12 Max. 0.6 Nm
Produktové číslo:
X67AM1323
Popis:
  • 2 analog inputs, 2 analog outputs, each 0 to 20 mA
  • Configurable digital input filters
  • Very short cycle times
  • Optimal shield grounding on all channels

The module is equipped with 2 inputs and 2 outputs with 12-bit digital converter resolution. The input/output signal range is 0 to 20 mA.

Automation Studio HW Upgrades Verze (Datum) Stáhnout
V2.6 HW Upgrade (X67AM1323F) EXE / 486 KB
V3.0 HW Upgrade (X67AM1323F) EXE / 485 KB
V4.0 HW Upgrade (X67AM1323) EXE / 554 KB
Certifikáty Verze (Datum) Stáhnout
244665 CSA HazLoc Certificate of Compliance X20, X67 PDF / 56 KB
E115267 UL CoC X67 PDF / 84 KB
Safe cutoff of potential groups PDF / 735 KB
TÜV 05 ATEX 7201 X PDF / 129 KB
X20, X67 KC certificates PDF / 6 MB
Dokumentace Verze (Datum) Stáhnout
Datasheet X67AM1323 PDF / 516 KB
X67 System User´s Manual PDF / 19 MB
E-CAD (Electro or EPLAN Templates) Verze (Datum) Stáhnout
X67 EPLAN P8 EXE / 85 MB
X67 EPLAN P8 from V2.4 EXE / 105 MB
M-CAD (Mechan. Templates) Verze (Datum) Stáhnout
3D File DXF/STEP X67 ZIP / 1 MB

Please choose country and language

B&R Logo

Please choose country

B&R Logo